ASTM-B574 2005

$35.75

B574-05 Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

Published By	Publication Date	Number of Pages
ASTM	2005	4

Guaranteed Safe Checkout

Categories: 77.150.40 - Nickel and chromium products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM B574-05

Historical Standard: Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

ASTM B574

Scope

1.1 This specification covers rod of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06035, N06455, N06058, and N06059)*, low-carbon nickel-molybdenum-chromium-tantalum (UNS N06210), low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenum-tungsten (UNS N06686) as shown in , for use in general corrosive service.

1.2 The following products are covered under this specification:

1.2.1 Rods 5/16to 3/4 in. (7.94 to 19.05 mm), exclusive, in diameter, hot or cold finished, solution annealed and pickled, or mechanically descaled.

1.2.2 Rods 3/4to 31/2 in. (19.05 to 88.9 mm), inclusive, in diameter, hot or cold finished, solution annealed, ground or turned.

1.2.3 Rods 1/4 to 3 1/2 in. (6.35 to 88.9 mm), inclusive, in diameter, solution annealed, cold finished, as cold finished, ground or turned (N06059 and N06686 only, see and ).

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Keywords

N06022; N06035; N06058; N06059; N06200; N06210; N06455; N06686; N10276; rod

ICS Code

ICS Number Code 77.150.40 (Nickel and chromium products)

DOI: 10.1520/B0574-05

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology Ordering Information Chemical Composition
2	Mechanical Properties and Other Requirements Dimensions and Permissible Variations TABLE 1 TABLE 2 TABLE 3 TABLE 4
3	Workmanship, Finish, and Appearance Sampling Number of Tests and Retests Specimen Preparation Test Methods TABLE 5 TABLE 6
4	Inspection Rejection and Rehearing Certification Product Marking Keywords X1. HEAT TREATMENT X1.1

Additional information

Standard Title	B574-05 Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod
Published Code	ASTM
Publication Date	2005
Pages Count	4
ICS Codes	77.150.40 - Nickel and chromium products