šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
BS EN ISO 19085-15:2021:2022 Edition

BS EN ISO 19085-15:2021:2022 Edition

$198.66

Woodworking machines. Safety – Presses

Published By Publication Date Number of Pages
BSI 2022 58
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

This part of ISO 19085 gives the safety requirements and measures for stationary manually loaded and unloaded: – cold presses, – hot presses, – bending presses, – edge/face gluing presses, – membrane presses, – embossing presses, where pressing force is applied by hydraulic actuators pushing two flat or shaped surfaces against each other, hereinafter referred to as “machines”. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE: For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: – Device for hot gluing – Device for high frequency gluing – Device for high frequency shaping – Automatic work-piece loading and unloading system – intermediate additional platens – work-piece extractor – work-piece clamping pressure beam – split moveable platens. The machines are designed to process work-pieces consisting of: – solid wood; – materials with similar characteristics to wood (see ISO 19085-1:2017, 3.2); – honeycomb. This part of ISO 19085 does not deal with any hazards related to: – specific devices that differ from the list above; – hot fluid heating systems internal to the machine other than electrical; – any hot fluid heating systems external to the machine; – operation of taking intermediate platens out and in again; – the combination of a single machine being used with any other machine (as part of a line). It is not applicable to: – frame presses; – membrane presses where the pressing force is applied by vacuum only; – presses for producing chipboard, fibreboard, OSB; – machines intended for use in potentially explosive atmosphere; – machines manufactured before the date of its publication as an international standard.

PDF Catalog

PDF Pages PDF Title
2 undefined
7 Annex ZA (informative)Relationship between this European Standard and the essential requirements of EU Directive 2006/42/EC aimed to be covered
11 Foreword
12 Introduction
15 1 Scope
16 2 Normative references
17 3 Terms and definitions
26 4 List of significant hazards
28 5 Safety requirements and measures for controls
5.1 Safety and reliability of control systems
5.2 Control devices
29 5.3 Start
5.4 Safe stops
5.4.1 General
5.4.2 Normal stop
30 5.4.3 Operational stop
5.4.4 Emergency stop
5.5 Braking function of tool spindles
5.6 Mode selection
5.7 Spindle speed changing
5.7.1 Spindle speed changing by changing belts on the pulleys
5.7.2 Spindle speed changing by incremental speed change motor
5.7.3 Infinitely variable speed by frequency inverter
5.8 Failure of any power supply
31 5.9 Manual reset control
5.10 Enabling control
5.11 Machine moving parts speed monitoring
5.12 Time delay
6 Safety requirements and measures for protection against mechanical hazards
6.1 Stability
6.1.1 General
32 6.1.2 Displaceable machines
6.2 Risk of break-up during operation
6.3 Tool holder and tool design
6.3.1 General
6.3.2 Spindle locking
6.3.3 Circular saw blade fixing devices
33 6.3.4 Flange dimensions for circular saw blades
6.4 Braking
6.4.1 Braking of tool spindles
6.4.2 Maximum run-down time
6.4.3 Brake release
6.5 Safeguards
6.5.1 Fixed guards
6.5.2 Interlocking moveable guards
6.5.3 Hold-to-run control
6.5.4 Two hand control
6.5.5 Electro-sensitive protective equipment (ESPE)
6.5.6 Pressure sensitive protective equipment (PSPE)
34 6.6 Prevention of access to moving parts
6.6.1 General
6.6.2 Guarding of tools
6.6.3 Guarding of drives
6.6.4 Guarding of shearing and/or crushing zones
38 6.7 Impact hazard
6.8 Clamping devices
39 6.9 Measures against ejection
6.9.1 General
6.9.2 Guards materials and characteristics
6.10 Work-piece support and guides
40 7 Safety requirements and measures for protection against other hazards
7.1 Fire
7.2 Noise
7.2.1 Noise reduction at the design stage
41 7.2.2 Noise emission measurement and declaration
7.3 Emission of chips and dust
42 7.4 Electricity
7.4.1 General
43 7.4.2 Displaceable machines
7.5 Ergonomics and handling
7.6 Lighting
7.7 Pneumatics
7.8 Hydraulics
7.9 Electromagnetic compatibility
7.10 Laser
7.11 Static electricity
7.12 Errors of fitting
7.13 Isolation
44 7.14 Maintenance
7.15 Extreme temperatures
8 Information for use
8.1 Warning devices
8.2 Marking
8.2.1 General
8.2.2 Additional markings
8.3 Instruction handbook
8.3.1 General
45 8.3.2 Additional information
46 Annex A (informative) Performance level required
47 Annex B (normative) Tests for braking function
48 Annex C (normative) Stability test for displaceable machines
49 Annex D (normative) Impact test for guards
50 Annex E (normative) Noise test code
56 Bibliography

Related products

BS EN ISO 19085-15:2021
$198.66