AS ISO 9360.1:2003
$49.40
Anaesthetic and respiratory equipment – Heat and mositure exchangers (HMEs) for humidifying respired gases in humans – HMEs for use with minimum tidal volumes of 250 ml
Published By | Publication Date | Number of Pages |
AS | 2003-06-30 | 28 |
If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]
Specifies certain requirements for heat and moisture exchangers, including those incorporating breathing system filters, intended for the humidification of respired gases for use primarily with patients with a tidal volume equal to or greater than 250 ml, and incorporating at least one machine port, and describes test methods for their evaluation.
Scope
This part of ISO 9360 specifies certain requirements for heat and moisture exchangers (HMEs), including those incorporating breathing system filters, intended for the humidification of respired gases for use primarily with patients with a tidal volume equal to or greater than 250 ml, and incorporating at least one machine port, and describes test methods for their evaluation.
Published Code | AS |
---|---|
Published By | Australia Standards |
Publication Date | 2003-06-30 |
Pages Count | 28 |
Language | English |
Edition | 1 |
File Size | 327.7 KB |
ISBN | 0733753485 |
ICS Codes | 11.040.10 - Anaesthetic, respiratory and reanimation equipment |
Related products
-
BS EN ISO 9360-2:2002
Anaesthetic and respiratory equipment. Heat and moisture exchangers (HMEs) for humidifying respired gases in humans…
-
ISO 9360-1:2000
Anaesthetic and respiratory equipment — Heat and moisture exchangers (HMEs) for humidifying respired gases in…
-
AS ISO 9360.2:2003
Anaesthetic and respiratory equipment – Heat and mositure exchangers (HMEs) for humidifying respired gases in…
-
BS EN ISO 15087-3:2000
Dental elevators – Cryer elevators Published By Publication Date Number of Pages BSI 2000 14
-
BS 3601:1987
Specification for carbon steel pipes and tubes with specified room temperature properties for pressure purposes…
-
BS ISO 3601-1:2012+A1:2019
Fluid power systems. O-rings – Inside diameters, cross-sections, tolerances and designation codes Published By Publication…
-
ISO 7089:2000
Rondelles plates — Série normale — Grade A Published By Publication Date Number of Pages…
-
ISA 60079-0 (12.00.01)-2009
Explosive atmospheres – Part 0: Equipment – General Requirements Published By Publication Date Number of…
-
BS EN ISO 9360-1:2009
Anaesthetic and respiratory equipment. Heat and moisture exchangers (HMEs) for humidifying respired gases in humans…
-
ISO/TR 18392:2005
Surface chemical analysis — X-ray photoelectron spectroscopy — Procedures for determining backgrounds Published By Publication…
-
ISA 60079-18 (12.23.01)-2009
Electrical Apparatus for Use in Class I, Zone 1 Hazardous (Classified) Locations: Type of Protection…
-
BS ISO 23601:2009:2010 Edition
Safety identification. Escape and evacuation plan signs Published By Publication Date Number of Pages BSI…
-
ISO 9360-2:2001
Anaesthetic and respiratory equipment — Heat and moisture exchangers (HMEs) for humidifying respired gases in…
-
ISO 9301:2003
Oil of cumin seed (Cuminum cyminum L.) Published By Publication Date Number of Pages ISO…
-
BS EN ISO 27107:2008:2009 Edition
Animal and vegetable fats and oils. Determination of peroxide value. Potentiometric end-point determination Published By…
-
AS ISO 5366.1:2004
Anaesthetic respiratory equipment – Tracheostomy tubes – Tubes and connectors for use in adults (ISO…
-
ISO 9096:2003
Stationary source emissions — Manual determination of mass concentration of particulate matter Published By Publication…
-
BS EN ISO 9360-1:2000
Anaesthetic and respiratory equipment. Heat and moisture exchangers (HMEs) for humidifying respired gases in humans…
-
ISO 3601-3:2005
Transmissions hydrauliques et pneumatiques — Joints toriques — Partie 3: Critères de qualité Published By…
-
BS ISO 18907:2000
Imaging materials. Photographic films and papers. Wedge test for brittleness Published By Publication Date Number…
-
BS ISO 3601-1:2008:2010 Edition
Fluid power systems. O-rings – Inside diameters, cross-sections, tolerances and designation codes Published By Publication…
-
ISA 60079-5 (12.00.04)-2009
Explosive Atmospheres – Part 5: Equipment Protection by Powder Filling “q” Published By Publication Date…
-
BS ISO 23601:2020
Safety identification. Escape and evacuation plan signs Published By Publication Date Number of Pages BSI…
-
AS/NZS 4276.22:2007
Water microbiology – Method 22: Packaged water – Coliform bacteria and Escherichia coli – Membrane…
-
BS EN ISO 9360-2:2009
Anaesthetic and respiratory equipment. Heat and moisture exchangers (HMEs) for humidifying respired gases in humans…
-
BS EN 50090-3-2:2004
Home and building electronic systems (HBES) – Aspects of application – User process for HBES…
-
BS ISO 3601-2:2008
Fluid power systems. O-rings – Housing dimensions for general applications Published By Publication Date Number…
-
BS 903-A60.1:2000
Physical testing of rubber. Curemetering – Guide to the use of curemeters Published By Publication…
-
BS EN 10216-1:2002
Seamless steel tubes for pressure purposes. Technical delivery conditions Published By Publication Date Number of…
-
BS ISO 3601-2:2016:2017 Edition
Fluid power systems. O-rings – Housing dimensions for general applications Published By Publication Date Number…
-
ISA TR91.00.02-2003
Criticality Classification Guideline for Instrumentation Published By Publication Date Number of Pages ISA 2003-01-02 30
-
BS EN 10216-1:2013
Seamless steel tubes for pressure purposes. Technical delivery conditions – Non-alloy steel tubes with specified…
-
BS ISO 6328:2000
Photography. Photographic materials. Determination of ISO resolving power Published By Publication Date Number of Pages…
-
ISO 3601-5:2002
Fluid power systems — O-rings — Part 5: Suitability of elastomeric materials for industrial applications…
-
BS ISO/TS 16799:1999:2000 Edition
Rolling bearings. Dynamic load ratings and rating life. Discontinuities in the calculating of basic dynamic…
-
BS ISO 3601-4:2008
Fluid power systems. O-rings – Anti-extrusion rings (back-up rings) Published By Publication Date Number of…
-
BS ISO 3601-3:2005+A1:2018
Fluid power systems. O-rings – Quality acceptance criteria Published By Publication Date Number of Pages…
-
ISO 3601-2:2008
Fluid power systems — O-rings — Part 2: Housing dimensions for general applications Published By…
-
BS EN 10217-1:2002:2006 Edition
Welded steel tubes for pressure purposes. Technical delivery conditions – Non-alloy steel tubes with specified…
-
ISO 3601-4:2008
Fluid power systems — O-rings — Part 4: Anti-extrusion rings (back-up rings) Published By Publication…