Shopping Cart

No products in the cart.

ASME A112.19.3 2008 R2013

$98.04

ASME A112.19.3 Stainless Steel Plumbing Fixtures – Reaffirmed: 2013

Published By Publication Date Number of Pages
ASME 2008 46
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

A112.19.3 covers plumbing fixtures made of stainless steel alloys. It specifies requirements for materials, construction, performance, testing, and markings. This Standard is a revision of ASME A112.19.3-2000 [R2004] and replaces CAN/CSA-B45.4-02. This Standard is “harmonized” – developed in response to industry requests for uniform standards that would be acceptable in both the United States and Canada. A112.19.1 / 2 / 3 are to be used in conjunction with components described in other volumes of the ASME A112 series. Careful application of these A112 standards will help users to comply with pertinent regulations, while achieving the operational and safety benefits to be gained from the many industry best-practices detailed within these volumes. Intended for manufacturers of plumbing materials and equipment to enhance water conservation and comply with jurisdictional regulation, plus governmental and other regulatory bodies.

PDF Catalog

PDF Pages PDF Title
1 ASME A112.19.3-2008/CSA B45.4-08 Stainless steel plumbing fixtures
3 Update No. 2
March 2011
5 4.4 Waste fitting openings, drainage, and overflows
4.4.1 Waste fitting openings and drainage
4.4.2 Overflows
4.5 Additional requirements for water closets
4.6 Additional requirements for urinals
4.7 Additional requirements for lavatories, sinks, and bidets
4.7.1 Openings and mounting surfaces for supply fittings
6 4.7.2 Laundry or utility sink capacity
4.8 Additional requirements for bathtubs and shower bases
4.8.1 Minimum dimensions for bathtubs
4.8.2 Slope to the waste outlet
4.8.3 Flanges
4.9 Additional requirements for drinking fountains
4.9.1
4.9.2
4.10 Accessible design fixtures
7 Update No. 1 July 2009
11 CSA Standards Update Service
17 ASME Standards Committee on Plumbing Materials and Equipment
19 ASME Project Team 19.3 – Stainless Steel Plumbing Fixtures
20 CSA Technical Committee on Plumbing Fixtures
22 ASME/CSA Joint Harmonization Task Group on Plumbing Fixtures
23 Preface
25 0 Introduction
0.1
0.2
0.3
1 Scope
1.1
1.2
26 1.3
1.4
2 Reference publications
27 3 Definitions
28 4 General requirements
4.1 Materials
4.2 Stainless steel thickness
4.2.1 Lavatories and sinks
4.2.2 Other fixtures
4.3 Tolerances
29 4.4 Waste fitting openings, drainage, and overflows
4.4.1 Waste fitting openings and drainage
4.4.2 Overflows
4.5 Additional requirements for water closets
4.6 Additional requirements for urinals
4.7 Additional requirements for lavatories, sinks, and bidets
4.7.1 Openings and mounting surfaces for supply fittings
30 4.7.2 Laundry or utility sink capacity
4.8 Additional requirements for bathtubs and shower bases
4.8.1 Minimum dimensions for bathtubs
4.8.2 Slope to the waste outlet
4.8.3 Flanges
4.9 Additional requirements for drinking fountains
4.9.1
4.9.2
4.10 Accessible design fixtures
31 5 Tests
5.1 Surface examination
5.1.1 Procedure
5.1.2 Performance
5.2 Warpage test
5.2.1 Procedure
5.2.2 Performance
5.3 Field-installed flange test
5.3.1 Procedure
5.3.2 Performance
32 5.4 Overflow test
5.4.1 Procedure
5.4.2 Performance
5.5 Structural integrity tests
5.5.1 Water closets
5.5.2 Lavatories and sinks
33 5.5.3 Wall-mounted urinals
5.5.4 Bathtubs and shower bases
34 6 Markings, packaging, and installation instructions and other literature
6.1 General
6.1.1
35 6.1.2
6.1.3
6.2 Non-standard fixtures
6.2.1
6.2.2
6.3 Additional markings for water closets and urinals
6.4 Field-installed flanges
6.5 Packaging and installation instructions and other literature
6.5.1 General
6.5.2 Packaging
36 6.5.3 Installation instructions
42 Annex A (informative)
A.1 Conversion rules
A.2 Rounding rules
ASME A112.19.3 2008 R2013
$98.04