ASME A112.19.4M 1994 R2009
$98.04
ASME A112.19.4M Porcelain Enameled Formed Steel Plumbing Fixtures – Reaffirmed: 2009
| Published By | Publication Date | Number of Pages |
| ASME | 1994 | 44 |
There is a newer edition of this standard available. It is ASME A112.19.1/CSA B45.2-2008, Enameled Cast Iron and Steel Plumbing Fixtures. It is a consolidation and revision of ASME A112.19.1M-1994 and ASME A112.19.4M-1994. It also replaces CAN/CSA-B45.2-02 and CAN/CSA-B45.3-02. This Standard covers materials, methods of inspection, dimensions, testing, and identification of porcelain enameled formed steel plumbing fixtures, such as bathtubs, sinks, and lavatories, which are in general use and demand.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Supplement 2 – 2000 |
| 3 | Supplement 1 – 1998 |
| 5 | Errata – November 1996 |
| 15 | Foreword |
| 17 | Standards Committee Roster |
| 19 | Contents Figures Table Nonmandatory Appendices |
| 21 | 1 Purpose, Scope, and Reference Standards 1.1 Purpose 1.2 Scope 1.3 Reference Standards 2 Definitions |
| 22 | 3 Requirements 3.1 Materials 3.2 Sheet Steel 3.2.1 Thickness Fig. 1 Locations of Span Measurements |
| 23 | 3.3 Porcelain Enamel 3.3.1 Thickness 3.3.2 Appearance 3.3.3 Color, Specular Gloss, and Reflectance 3.3.4 Chemical Resistance 3.3.5 Abrasion Resistance 3.3.6 Slip Resistance 3.4 Structural Requirements 3.4.1 Warpage 3.4.2 Rigidity 3.4.3 Draining 3.5 Types and Sizes Table 1 Allowable Blemishes |
| 24 | Fig. 2 Location of Slip-Resisting Surfaces |
| 25 | 3.6 Dimensions and Tolerances 4 Fixture Types and Sizes 4.1 Bathtubs 4.1.1 Common Types and Sizes 4.1.2 Bathtub Overflows Fig. 3 Corner Bathtubs, Right or Left Fig. 4 Recess Bathtubs, Right or Left |
| 26 | 4.1.3 Bathtub Outlets 4.1.4 Flanges and Tiling Beads 4.2 Lavatories 4.2.1 Common Types and Sizes 4.2.2 Lavatory Overflows (Optional) 4.2.3 Lavatory Outlets 4.3 Kitchen Sinks 4.3.1 Common Types and Sizes Fig. 5 Drop-in or Island Type Bathtubs |
| 27 | Fig. 6 Bathtub Outlet and Overflow Dimensions Fig. 7 Bathtub Outlet and Overflow Dimensions for Above-the-Floor Roughing |
| 28 | Fig. 8 Round Lavatories Fig. 9 Oval Lavatories Fig. 10 Flat-Rim Lavatories With Ledge |
| 29 | Fig. 11 Rectangular Self-Rimming Lavatories Fig. 12 Round Self-Rimming Lavatories Fig. 13 Oval Self-Rimming Lavatories |
| 30 | 4.3.2 Kitchen Sink Outlets 4.3.3 Depth of Sinks Fig. 14 Lavatory Drain Outlets with Overflow Fig. 15 Self-Rimming and Flat-Rim Kitchen Sinks |
| 31 | 5 Methods of Inspection and Testing 5.1 Porcelain Enamel 5.1.1 Thickness 5.1.2 Surface Inspection for Blemishes 5.1.3 Specular Gloss 5.1.4 Reflectance 5.1.5 Acid Resistance 5.1.6 Alkali Resistance 5.1.7 Abrasion Resistance Fig. 16 Self-Rimming and Flat-Rim Ledge Kitchen Sinks |
| 32 | 5.2 Structural Tests 5.2.1 Warpage Test 5.2.2 Rigidity Tests 5.2.2.1 Bathtubs Fig. 17 Self-Rimming and Flat-Rim Ledge Kitchen Sinks, Double Compartment |
| 33 | Fig. 18 Self-Rimming and Flat-Rim Kitchen Sinks, Reversible Fig. 19 Kitchen Sink Outlet Dimensions |
| 34 | 5.2.2.2 Lavatories and Sinks |
| 35 | 5.2.2.3 Surface Inspection Procedures 5.3 Test for Flange-Fixture Seal (Laboratory Tests for Field Installation Units Only) 5.3.1 Preparation 5.3.2 Test Method 5.3.3 Performance Requirement 6 Identification 6.1 Markings 6.2 Label |
| 37 | Appendix A Government Requirements A1 SCOPE A2 APPLICABLE DOCUMENTS A3 REQUIREMENTS A3.1 Definitive Part Number (DPN) A3.1.1 Part Numbers for Bathtub (Fixture Designation= 1) A3.1.2 Part Numbers for Lavatory (Fixture Designation = 2) |
| 38 | A3.1.3 Part Numbers for Kitchen Sink (Fixture Designation = 3) A3.2 Standard Commercial Product A4 QUALITY ASSURANCE PROVISIONS A4.1 Responsibility for Inspection A4.2 Quality Conformance Inspection A4.3 Sampling |
| 39 | A5 PREPARATION FOR DELIVERY A6 ORDERING DATA |
| 41 | Appendix B Metric (SI) Units Conversion Table |
