ASME AG 1 2023
$75.42
ASME AG-1-2023 Code on Nuclear Air and Gas Treatment
| Published By | Publication Date | Number of Pages |
| ASME | 2023 | 539 |
This Code provides requirements for the performance, design, fabrication, installation, inspection, acceptance testing, and quality assurance of equipment used in air and gas treatment systems in nuclear facilities. This Code also provides nonmandatory guidance for systems involving components covered by this Code.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | CONTENTS |
| 38 | FOREWORD |
| 39 | ASME COMMITTEE ROSTER |
| 45 | CORRESPONDENCE WITH THE COMMITTEE ON NUCLEAR AIR AND GAS TREATMENT |
| 47 | ORGANIZATION OF ASME AG-1 |
| 49 | ASME AG-1–2023 SUMMARY OF CHANGES |
| 54 | Division I General Requirements SECTION AA COMMON ARTICLES ARTICLE AA-1000 INTRODUCTION AA-1100 SCOPE AA-1200 PURPOSE AA-1300 APPLICABILITY AA-1400 DEFINITIONS AND TERMS |
| 58 | ARTICLE AA-2000 REFERENCED DOCUMENTS |
| 60 | ARTICLE AA-3000 MATERIALS AA-3100 GENERAL AA-3200 MATERIAL SUBSTITUTION AA-3300 MATERIAL TESTING AA-3400 CERTIFICATION OF MATERIALS ARTICLE AA-4000 STRUCTURAL DESIGN AA-4100 SCOPE AA-4110 Environmental Qualification AA-4200 DESIGN CRITERIA |
| 61 | Tables Table AA-3100-1 Allowable Materials |
| 65 | AA-4210 Load Criteria |
| 66 | AA-4220 Stress Criteria: Limits AA-4230 Deflection Criteria: Limits AA-4240 Other Criteria AA-4241 Vibration Isolation. AA-4242 Provisions for Relative Movement. AA-4243 Structural Attachments. Table AA-4212-1 Load Conditions Table AA-4230-1 Deflection Limits Table AA-4212-1 Load Conditions Table AA-4230-1 Deflection Limits |
| 67 | AA-4243.1 Integral Attachments AA-4243.2 Nonintegral Attachments. AA-4244 Rotating Equipment. AA-4300 DESIGN OF EQUIPMENT SYSTEMS AND THEIR SUPPORTING ELEMENTS AA-4310 General Requirements |
| 68 | AA-4320 Design Verification of Plate- and Shell-Type Components and Their Supporting Elements Table AA-4321-1 Plate- and Shell-Type Components: Primary Stress Allowables |
| 69 | AA-4330 Design Verification of Linear-Type Systems by Analysis Table AA-4331-1 Linear-Type Systems:Primary Stress Allowables |
| 70 | AA-4340 Functionality Requirements AA-4350 Design Verification by Seismic Qualification Testing |
| 73 | Figures Figure AA-4356.4-1 Oscillations per Beat |
| 74 | AA-4360 Design of Bolts AA-4400 DOCUMENTATION REQUIREMENTS AA-4410 Certification of Design Verification AA-4420 Equipment Description |
| 75 | AA-4430 Operating Features AA-4440 Report Content |
| 76 | ARTICLE AA-5000 INSPECTION AND TESTING AA-5100 GENERAL AA-5110 Scope and Applicability AA-5120 Responsibility for Procedures AA-5130 Measuring and Test Equipment AA-5200 VISUAL INSPECTION AA-5210 Scope AA-5220 Description of Method AA-5230 Requirements AA-5240 Inspection Checklist AA-5250 Reports AA-5300 WELDED CONNECTIONS AA-5400 BOLTED CONNECTIONS AA-5410 Before Bolting |
| 77 | AA-5420 After Bolting AA-5500 FABRICATION TOLERANCES AA-5600 PRESSURE AND LEAK TESTING AA-5700 PERFORMANCE AND FUNCTIONAL TESTING AA-5800 SEISMIC TESTING ARTICLE AA-6000 FABRICATION, JOINING, WELDING, BRAZING, PROTECTIVE COATING, AND INSTALLATION AA-6100 GENERAL AA-6110 Scope and Applicability AA-6120 Materials AA-6130 Control of Fabrication and Installation Processes AA-6200 FABRICATION PROCESSES AA-6210 Cutting, Forming, and Bending AA-6220 Forming Tolerances AA-6230 Fitting and Aligning |
| 78 | AA-6240 Welded Joints AA-6250 Mechanical Joints AA-6251 Fasteners and Threaded Joints. AA-6252 Structural and Pressure Boundary Fasteners. AA-6253 Thread Lubricants. AA-6254 Removal of Thread Lubricants. AA-6255 Bolted Connections. AA-6256 Precautions Before Bolting. AA-6257 Bolt Tension. AA-6258 Locking Devices. AA-6300 WELDING REQUIREMENTS AA-6310 General |
| 79 | AA-6320 Workmanship |
| 80 | Figure AA-6324.2-1 Acceptable and Unacceptable Weld Profiles |
| 81 | AA-6330 Inspection and Testing of Welds |
| 82 | AA-6400 BRAZING AA-6410 General AA-6420 Workmanship AA-6430 Inspection and Testing |
| 83 | AA-6500 CLEANING AND COATING AA-6510 General AA-6520 Design Considerations for Coating |
| 84 | AA-6530 Repair of Coating System AA-6540 Cleanliness AA-6541 Component Cleanliness AA-6541.1 Cleanliness of Moisture Separators. AA-6541.2 Cleanliness of Filter Cells. AA-6541.3 Cleanliness of Type III Adsorbers. AA-6541.4 Cleanliness of Mounting Frames. AA-6541.5 Cleanliness of Control Panels. AA-6542 Surface Preparation. AA-6543 Cleaning and Finishing. AA-6543.1 Surface Preparation |
| 85 | AA-6543.2 Coating and Application. AA-6544 Coating of Filter Mounting Frames. AA-6550 Quality Assurance Requirements and Documentation AA-6551 Quality Assurance Program. AA-6552 Inspection. AA-6553 Coating Inspector’s Qualification. |
| 86 | AA-6554 Quality Control Process. AA-6555 Coating Applicator’s Qualifications. AA-6556 Control of Coating Manufacturing. AA-6600 INSTALLATION REQUIREMENTS AA-6610 Handling and Rigging AA-6620 Field Assembly AA-6630 Temporary Field Attachments |
| 87 | ARTICLE AA-7000 PACKAGING, SHIPPING, RECEIVING, STORAGE, AND HANDLING AA-7100 GENERAL AA-7110 Scope and Applicability AA-7120 Responsibility AA-7200 GENERAL REQUIREMENTS AA-7210 Planning, Procedures, and Instructions AA-7220 Personnel Qualifications AA-7230 Classification of Items AA-7300 PACKAGING AA-7310 General |
| 88 | AA-7320 Level of Packaging AA-7400 SHIPPING ARTICLE AA-8000 QUALITY ASSURANCE AA-8100 GENERAL AA-8110 Scope and Applicability AA-8120 Responsibility AA-8130 Responsibilities of Fabricators, Material Suppliers, and Material Manufacturers Figure AA-8130-1 Hierarchy of Responsibility |
| 89 | AA-8200 IDENTIFICATION AND CONTROL OF ITEMS AA-8210 Documentation AA-8220 Identification and Completed Material AA-8230 Marking Requirements for Small Products AA-8240 Certified Material Test Reports AA-8250 Records of Examinations and Tests AA-8300 QUALITY ASSURANCE RECORDS ARTICLE AA-9000 NAMEPLATES AND STAMPING AA-9100 SCOPE AND APPLICABILITY AA-9200 REQUIREMENTS |
| 90 | AA-9210 Attachment of Nameplates AA-9220 Location of Nameplates ARTICLE AA-10000 REPAIR AND REPLACEMENT OF COMPONENTS AA-10100 GENERAL AA-10110 Scope AA-10120 Applicability AA-10200 WELDING AA-10300 REPAIRS |
| 91 | AA-10400 REPLACEMENTS AA-10410 Routine Maintenance AA-10420 Suitability AA-10430 Additional Documentation AA-10500 RECORDS AA-10510 General Requirements AA-10520 Records Index AA-10530 Lifetime Records |
| 92 | AA-10540 Nonpermanent Records Table AA-10530-1 Lifetime Repair and Replacement Records Table AA-10540-1 Nonpermanent Repair and Replacement Records |
| 93 | NONMANDATORY APPENDIX AA-A DESIGN AND QUALIFICATION BY ANALYSIS ARTICLE AA-A-1000 INTRODUCTION ARTICLE AA-A-2000 FINITE ELEMENT METHOD Table AA-A-1000-1 Analysis Considerations |
| 94 | ARTICLE AA-A-3000 EQUIPMENT CONSTRUCTION ARTICLE AA-A-4000 MODELING TECHNIQUES AA-A-4100 AIR HANDLING UNIT (AHU) MODEL |
| 95 | AA-A-4200 FAN MODEL AA-A-4300 INSTRUMENTS AND CONTROLS (I&C) CABINETS AA-A-4400 DUCT SUPPORTS AA-A-4500 EQUIPMENT SUPPORTS ARTICLE AA-A-5000 ANALYSIS AA-A-5100 STATIC LOADS |
| 96 | Figure AA-A-4200-1 Isometric View of a Typical Fan Model |
| 97 | Figure AA-A-4300-1 Isometric View of a Typical I&C Cabinet Model |
| 98 | Figure AA-A-4400-1 Isometric View of a Typical Duct Support Model |
| 99 | AA-A-5200 DYNAMIC ANALYSIS AA-A-5210 Dynamic Loads AA-A-5220 Dynamic Analysis Techniques AA-A-5230 Input Motion Figure AA-A-4500-1 Isometric View of a Typical Refrigeration Equipment Support |
| 100 | AA-A-5240 Two-Step Analysis ARTICLE AA-A-6000 EVALUATION OF RESULTS AA-A-6100 STRESSES AA-A-6200 DEFLECTIONS AA-A-6300 SUPPORT LOADS AA-A-6400 CONNECTION LOADING AA-A-6500 DEVICE LOADING ARTICLE AA-A-7000 SAMPLE PROBLEMS AA-A-7100 SCOPE AA-A-7200 SAMPLE AHU ANALYSIS |
| 101 | Figure AA-A-7200-1 Computer Plots of Finite Element Model of Sample AHU (Perspective View of Tri-Plate Mesh) |
| 103 | AA-A-7300 DUCT SUPPORT (HANGER) SAMPLE PROBLEM AA-A-7310 Hanger Model AA-A-7320 Analysis |
| 105 | Figure AA-A-7310-1 Typical Duct Support As-Built (Dimensions and Member Sizes Not Shown) |
| 106 | Figure AA-A-7311-1 Ductwork Support Baseplate Model |
| 107 | Figure AA-A-7324-1 Effective Duct Cross Section |
| 108 | Figure AA-A-7325-1 Typical Duct System Model |
| 109 | NONMANDATORY APPENDIX AA-B SEISMIC QUALIFICATION BY TESTING ARTICLE AA-B-1000 TEST PLAN ARTICLE AA-B-2000 OUTLINE FOR TYPICAL SEISMIC TEST PLAN AA-B-2100 PURPOSE AA-B-2200 SCOPE AA-B-2300 TEST SPECIMENS AA-B-2400 SPECIAL EQUIPMENT OR FIXTURES (IF REQUIRED) AA-B-2500 TEST SETUP AA-B-2600 TEST REQUIREMENTS AA-B-2700 ACCEPTANCE/FAILURE CRITERIA AA-B-2800 TEST PROCEDURE |
| 110 | AA-B-2900 FINAL REPORT ARTICLE AA-B-3000 COMMENTARY ON OUTLINE FOR TYPICAL SEISMIC TEST PLAN AA-B-3100 PURPOSE AA-B-3200 SCOPE AA-B-3300 TEST SPECIMENS AA-B-3400 SPECIAL EQUIPMENT OR FIXTURES AA-B-3500 TEST SETUP |
| 111 | AA-B-3600 TEST REQUIREMENTS |
| 112 | AA-B-3700 ACCEPTANCE AND FAILURE CRITERIA AA-B-3800 TEST PROCEDURE AA-B-3900 FINAL REPORT |
| 113 | NONMANDATORY APPENDIX AA-C QUALIFICATION BY A COMBINATION OF ANALYSIS AND TESTING ARTICLE AA-C-1000 INTRODUCTION ARTICLE AA-C-2000 QUALIFICATION BY ANALYSIS ONLY ARTICLE AA-C-3000 QUALIFICATION BY TESTING ONLY AA-C-3100 TESTING PROGRAM CONSIDERATIONS ARTICLE AA-C-4000 SUPPORTING TEST AA-C-4100 COMMON APPLICATIONS AA-C-4200 DYNAMIC AND STATIC SUPPORTING TESTS AA-C-4210 Dynamic Supporting Tests |
| 114 | AA-C-4220 Static Supporting Tests |
| 115 | SECTION AB SYSTEM DESIGN GUIDE ARTICLE AB-1000 INTRODUCTION AB-1100 SCOPE AB-1200 PURPOSE AB-1300 APPLICABILITY AB-1400 DEFINITIONS AND TERMS ARTICLE AB-2000 REFERENCED DOCUMENTS |
| 116 | ARTICLE AB-3000 FUNCTIONAL DESCRIPTION AB-3100 POWER GENERATION FACILITIES AB-3110 Air Treatment Systems for DBA Requirements AB-3120 Normal Operation Systems ARTICLE AB-4000 TYPICAL AIR TREATMENT SYSTEM AB-4100 SYSTEM FUNCTION AB-4200 SYSTEM BOUNDARIES AB-4300 SYSTEM INTERFACES |
| 117 | AB-4400 SYSTEM DESIGN AB-4410 SGTS Typical Components AB-4420 SGTS Required Design Parameters |
| 118 | AB-4500 SYSTEM OPERATION AB-4510 Recommendation for Control of Heat of Radioactive Decay and Heat of Oxidation AB-4600 SYSTEM INTERLOCKS AND ALARMS ARTICLE AB-5000 COMPONENT DESIGN AB-5100 FILTER TRAIN COMPONENTS AB-5110 Description AB-5120 Applications AB-5130 Cautions and Concerns |
| 119 | AB-5140 Recommendations for Installation AB-5150 Recommendations for Maintainability AB-5160 Recommendations for Fire Detection AB-5170 Recommendations for Fire Protection |
| 120 | AB-5200 HEATERS AB-5210 Description AB-5220 Applications AB-5230 Cautions and Concerns AB-5240 Recommendations for Installation AB-5250 Recommendations for Maintainability |
| 121 | AB-5260 Recommendations for Fire Protection AB-5300 FANS AB-5310 Description AB-5320 Applications AB-5330 Cautions and Concerns AB-5340 Recommendations for Installation |
| 122 | AB-5350 Recommendations for Maintainability AB-5360 Recommendations for Fire Protection AB-5400 VALVES, PIPING, COOLING COILS AB-5410 Description AB-5420 Applications AB-5430 Cautions and Concerns AB-5440 Recommendations for Installation |
| 123 | AB-5450 Recommendations for Maintainability AB-5460 Recommendations for Fire Protection AB-5500 DUCT AND DAMPERS AB-5510 Description AB-5520 Applications AB-5530 Cautions and Concerns AB-5540 Recommendations for Installation AB-5550 Recommendations for Maintainability AB-5560 Recommendations for Fire Protection AB-5600 INSTRUMENTATION AB-5610 Description |
| 124 | AB-5620 Applications AB-5630 Cautions and Concerns AB-5640 Recommendations for Installation AB-5650 Recommendations for Maintainability AB-5660 Recommendations for Fire Protection AB-5700 HOUSINGS AB-5710 Description AB-5720 Applications AB-5730 Cautions and Concerns AB-5740 Recommendations for Installation |
| 125 | AB-5750 Recommendations for Maintainability AB-5760 Recommendations for Fire Protection ARTICLE AB-6000 INSTALLATION AB-6100 SYSTEMS AB-6200 HOUSINGS AB-6300 COMPONENTS ARTICLE AB-7000 TESTING |
| 126 | ARTICLE AB-8000 TYPICAL STANDBY GAS TREATMENT FILTRATION SYSTEM AB-8100 Air Treatment Systems for DBA Requirements |
| 127 | Figure AB-8100-1 Typical Standby Gas Treatment Filtration System |
| 128 | Division II Ventilation Air Cleaning and Ventilation Air Conditioning SECTION BA FANS AND BLOWERS ARTICLE BA-1000 INTRODUCTION BA-1100 SCOPE BA-1200 PURPOSE BA-1300 APPLICABILITY BA-1400 DEFINITIONS AND TERMS |
| 129 | ARTICLE BA-2000 REFERENCED DOCUMENTS |
| 130 | ARTICLE BA-3000 MATERIALS BA-3100 GENERAL BA-3200 MATERIAL SUBSTITUTION BA-3300 MATERIAL TESTING BA-3400 CERTIFICATION OF MATERIALS ARTICLE BA-4000 DESIGN |
| 131 | BA-4100 DESIGN CONDITIONS BA-4110 Performance BA-4120 Environmental Conditions BA-4130 Seismic Conditions BA-4140 Loading |
| 132 | BA-4150 Leakage BA-4160 Support Boundary BA-4170 VIBRATION BA-4200 SELECTION BA-4210 Fans |
| 133 | BA-4220 Drivers BA-4300 CONSTRUCTION BA-4310 General BA-4320 Fans |
| 134 | BA-4330 Drivers and Drives BA-4340 Accessories |
| 135 | BA-4400 REPORTS AND CALCULATIONS BA-4410 Performance Rating BA-4420 Equipment Sound Production: Sound Level Data Report BA-4430 Design Verification Considerations |
| 136 | ARTICLE BA-5000 INSPECTION AND TESTING BA-5100 FAN INSPECTION AND TESTING BA-5110 Test Facilities BA-5120 Instrument Calibration BA-5130 Qualification Records BA-5140 Documentation BA-5200 FAN TESTING BA-5210 Performance Ratings BA-5220 Performance Tests BA-5230 Sound Tests BA-5240 Mechanical Tests |
| 137 | ARTICLE BA-6000 FABRICATION AND INSTALLATION OF CENTRIFUGAL AND AXIAL FANS BA-6100 FABRICATION BA-6110 Selection of Materials BA-6200 INSTALLATION ARTICLE BA-7000 PACKAGING, SHIPPING, RECEIVING, STORAGE, AND HANDLING BA-7100 GENERAL BA-7200 PACKAGING BA-7300 SHIPPING BA-7400 RECEIVING BA-7500 STORAGE BA-7600 DRIVERS SHIPPED SEPARATELY BA-7610 Short-Term |
| 138 | BA-7620 Long-Term (Over 6 Months) ARTICLE BA-8000 QUALITY ASSURANCE BA-8100 GENERAL BA-8200 REQUIRED DOCUMENTATION FOR FANS BA-8210 Certified Fan Performance Curves BA-8220 Material Certification BA-8300 DRAWINGS AND DOCUMENTATION ARTICLE BA-9000 NAMEPLATES AND OPERATING AND MAINTENANCE MANUALS BA-9100 GENERAL BA-9200 FANS BA-9210 Required Nameplate Data BA-9220 Drivers BA-9300 ACCEPTABLE METHODS FOR MARKING ACCESSORIES BA-9400 OPERATING AND MAINTENANCE MANUALS |
| 139 | NONMANDATORY APPENDIX BA-A FAN SYSTEM CONSIDERATIONS ARTICLE BA-A-1000 FAN SYSTEM CONSIDERATIONS BA-A-1100 SYSTEM CHARACTERISTICS BA-A-1200 SYSTEM EFFECTS ON FAN PERFORMANCE BA-A-1300 FAN AND SYSTEM MATCHING BA-A-1400 FAN-SYSTEM CAPACITY CONTROL BA-A-1500 MULTIPLE FAN SYSTEMS |
| 140 | NONMANDATORY APPENDIX BA-B DIVISION OF RESPONSIBILITY |
| 141 | Table BA-B-1000-1 Division of Responsibility |
| 143 | SECTION DA DAMPERS AND LOUVERS ARTICLE DA-1000 INTRODUCTION DA-1100 SCOPE DA-1200 PURPOSE DA-1300 APPLICABILITY DA-1310 Exclusion of Items DA-1320 Exclusion of Specific Designs DA-1330 Boundary Limits DA-1400 DEFINITIONS AND TERMS DA-1410 Components DA-1420 Function |
| 144 | DA-1430 Configuration DA-1440 Leakage and Blade Operating Positioning DA-1450 Pressure DA-1460 Temperature DA-1470 Tests DA-1480 Construction DA-1490 Torque |
| 145 | ARTICLE DA-2000 REFERENCED DOCUMENTS ARTICLE DA-3000 MATERIALS DA-3100 ALLOWABLE MATERIALS DA-3110 Materials of Construction DA-3120 Allowable Stress DA-3130 Bearing Materials DA-3140 Seal Materials DA-3200 SPECIAL LIMITATIONS ON MATERIALS DA-3210 Metals DA-3220 Nonmetallic Materials DA-3230 Deterioration of Materials in Service DA-3300 CERTIFICATION OF MATERIALS ARTICLE DA-4000 DESIGN DA-4100 GENERAL DESIGN |
| 146 | DA-4110 Requirements of Design Specifications DA-4120 Requirements of the Manufacturer DA-4130 Performance Requirements DA-4200 TECHNICAL REQUIREMENTS DA-4210 Structural |
| 147 | DA-4220 Thermal Expansion DA-4230 Torque |
| 148 | DA-4240 Linkage DA-4250 Bearings |
| 149 | DA-4260 Seals DA-4270 Frame Construction DA-4280 Mounting of Actuators and Accessories DA-4300 ACTUATORS DA-4310 Power-Operated Actuators |
| 150 | DA-4320 Manual Actuators DA-4330 Self-Contained Actuators DA-4340 Heat- or Temperature-Operated Actuators DA-4400 ACCESSORIES DA-4410 Accessory Requirements DA-4420 Auxiliary Energy Source DA-4430 Modulating Actuator Requirements DA-4440 Position Indicators DA-4450 Environmental Design Requirements DA-4460 Piping of Pneumatic Actuators DA-4470 Electrical Wiring Requirements ARTICLE DA-5000 INSPECTION AND TESTING DA-5100 TESTING |
| 151 | DA-5110 Pressure Drop Testing DA-5120 Cycle Time and Cycle Repetition DA-5130 Frame Leakage Testing for Frame Leakage Class A, B, or C DA-5140 Seat Leakage Testing ARTICLE DA-6000 FABRICATION, FINISHING, AND INSTALLATION DA-6100 WELDING AND BRAZING |
| 152 | ARTICLE DA-7000 PACKAGING, SHIPPING, AND STORAGE ARTICLE DA-8000 QUALITY ASSURANCE DA-8100 DAMPER AND LOUVER PERFORMANCE DA-8300 QUALITY ASSURANCE RECORDS ARTICLE DA-9000 NAMEPLATES, STAMPING, AND MANUALS DA-9100 NAMEPLATES AND STAMPING DA-9200 MANUALS |
| 153 | MANDATORY APPENDIX DA-I SEAT AND FRAME LEAKAGE Table DA-I-1000-1 Maximum Permissible Seat Leakage Rate, scfm/ft2 (scmh/m2), of Damper or Adjustable Louver Face Area at 1 in. wg (25.4 mm wg) Differential Pressure Table DA-I-1000-2 Maximum Permissible Frame Leakage Rate Classes at Frame Design Pressure |
| 154 | MANDATORY APPENDIX DA-II DAMPER AND LOUVER CONFIGURATIONS |
| 155 | Figure DA-II-1000-1 Parallel-Blade Dampers |
| 156 | Figure DA-II-1000-2 Wing-Blade Damper Figure DA-II-1000-3 Poppet Damper |
| 157 | Figure DA-II-1000-4 Opposed-Blade Damper Figure DA-II-1000-5 Single-Blade Damper |
| 158 | Figure DA-II-1000-6 Slide-Gate Guillotine Damper |
| 159 | Figure DA-II-1000-7 Curtain-Type Dampers |
| 160 | Figure DA-II-1000-8 Louver |
| 161 | NONMANDATORY APPENDIX DA-A DIVISION OF RESPONSIBILITY |
| 162 | Table DA-A-1000-1 Division of Responsibility |
| 164 | SECTION SA DUCTWORK ARTICLE SA-1000 INTRODUCTION SA-1100 SCOPE SA-1200 PURPOSE SA-1300 APPLICABILITY SA-1400 DEFINITIONS AND TERMS |
| 165 | Figure SA-1300-1 Ductwork and Ductwork Support — Interface Boundary |
| 166 | ARTICLE SA-2000 REFERENCED DOCUMENTS ARTICLE SA-3000 MATERIALS SA-3100 GENERAL SA-3200 MATERIAL SUBSTITUTION SA-3300 MATERIAL TESTING SA-3400 MATERIAL SPECIFICATIONS |
| 167 | ARTICLE SA-4000 DESIGN SA-4100 GENERAL SA-4200 DESIGN CRITERIA SA-4210 Load Criteria SA-4220 Stress Criteria SA-4230 Deflection Criteria |
| 168 | SA-4240 Other Criteria SA-4300 DUCTWORK JOINTS AND SEAMS SA-4310 General SA-4320 Duct Joints and Seams |
| 169 | SA-4400 COMPONENTS SA-4410 Flexible Connections SA-4420 Gaskets SA-4430 Access Doors and Panels SA-4440 Ports for Testing and Maintenance SA-4450 Miscellaneous |
| 170 | SA-4500 PRESSURE BOUNDARY LEAKAGE SA-4510 General SA-4520 Applicability SA-4530 Evaluation |
| 171 | SA-4540 Leakage Testing SA-4600 DESIGN SPECIFICATION ARTICLE SA-5000 INSPECTION AND TESTING SA-5100 GENERAL SA-5110 Scope and Applicability SA-5120 Responsibility for Procedures SA-5200 VISUAL INSPECTION SA-5210 General Requirements SA-5220 Welded Connections SA-5230 Ductwork SA-5240 Ductwork Supports |
| 172 | SA-5300 PRESSURE BOUNDARY LEAKAGE TESTING SA-5310 General SA-5320 Systems Completeness SA-5330 Allowances for Testing System Leakage Rates by Sections SA-5340 Testing Procedures SA-5350 Documentation SA-5360 Acceptance Criteria SA-5400 STRUCTURAL CAPABILITY TESTS SA-5410 Ductwork Pressure Test |
| 173 | SA-5420 Longitudinal Seam Qualification Test ARTICLE SA-6000 FABRICATION AND INSTALLATION SA-6100 GENERAL SA-6110 Scope and Applicability SA-6120 Materials SA-6130 Control of Installation and Fabrication Process SA-6140 Welding SA-6200 FABRICATION PROCESSES SA-6300 MECHANICAL FASTENING |
| 174 | SA-6400 FABRICATION TOLERANCES SA-6500 INSTALLATION TOLERANCES SA-6600 CLEANING, FINISHING, AND COATING ARTICLE SA-7000 PACKAGING, SHIPPING, RECEIVING, STORAGE, AND HANDLING SA-7100 GENERAL SA-7200 PACKAGING |
| 175 | Table SA-6400-1 Rectangular Ducts: Maximum Allowable Tolerances |
| 176 | Table SA-6400-2 Circular Ducts: Maximum Allowable Tolerances |
| 177 | SA-7300 SHIPPING SA-7400 RECEIVING SA-7500 STORAGE Table SA-6400-3 Flatness of Surface: Maximum Allowable Waviness Tolerance |
| 178 | ARTICLE SA-8000 QUALITY ASSURANCE SA-8100 GENERAL SA-8200 MATERIAL IDENTIFICATION SA-8300 DRAWINGS AND DOCUMENTATION ARTICLE SA-9000 NAMEPLATES AND STAMPING SA-9100 GENERAL SA-9200 STAMPING/MARKING SA-9210 Ducts SA-9220 Ductwork Supports SA-9230 Air Distribution Accessories |
| 179 | NONMANDATORY APPENDIX SA-A DIVISION OF RESPONSIBILITY Table SA-A-1000-1 Division of Responsibility |
| 180 | NONMANDATORY APPENDIX SA-B PROCEDURES TO DETERMINE ALLOWABLE LEAKAGE FOR DUCTWORK ARTICLE SA-B-1000 INTRODUCTION SA-B-1100 PURPOSE SA-B-1200 ALLOWABLE LEAKAGE BY HEALTH PHYSICS CRITERIA SA-B-1210 General SA-B-1220 Procedure to Determine Allowable Leakage by Maximum Permissible Concentration Method |
| 181 | Figure SA-B-1221-1 Allowable Unit Leakage From Duct or Housing to Occupied Space |
| 184 | Figure SA-B-1222-1 System Parameters |
| 185 | SA-B-1230 Allowable Leakage by Iodine Protection Factor Reduction |
| 186 | Figure SA-B-1232.1-1 Control Room System Flow Diagram |
| 187 | Figure SA-B-1232.2-1 Control Room System Flow Diagram With Leakage Paths |
| 189 | Table SA-B-1234-1 Control Room Air Cleaning System Parameters for Leakage Analysis Table SA-B-1234-2 Control Room Air Conditioning System Parameters for Leakage Analysis |
| 191 | SA-B-1300 ADDITIONAL LEAKAGE CRITERIA SA-B-1310 Air Cleaning System Effectiveness SA-B-1320 Air Cooling Effectiveness SA-B-1330 System Quality SA-B-1400 AIR CLEANING SYSTEM CONFIGURATIONS AND LEAKAGE CLASSES SA-B-1410 Leakage Classes |
| 192 | Table SA-B-1310-1 Maximum Allowable Leakage Factors for Air Cleaning Effectiveness |
| 193 | Figure SA-B-1410-1 Single-Pass Air Cleaning System Configuration |
| 194 | Figure SA-B-1410-2 Recirculating Air Cleaning System Configurations |
| 195 | Figure SA-B-1410-3 Recirculating Air Cleaning System Configurations |
| 196 | NONMANDATORY APPENDIX SA-C ADDITIONAL GUIDELINES FOR DUCT DESIGN AND CONSTRUCTION ARTICLE SA-C-1000 FUNCTIONAL DESIGN SA-C-1100 INTRODUCTION SA-C-1200 GENERAL SA-C-1210 Access Doors SA-C-1220 Drains SA-C-1230 Duct |
| 197 | SA-C-1240 Access for Service, Testing, and Inspection SA-C-1300 DUCT CONSTRUCTION STANDARDS Table SA-C-1300-1 Duct Construction Standards |
| 198 | SECTION HA HOUSINGS ARTICLE HA-1000 INTRODUCTION HA-1100 SCOPE HA-1200 PURPOSE HA-1300 APPLICABILITY Figure HA-1300-1 Housing, Air Cleaning Unit: Walk-In Type |
| 199 | Figure HA-1300-2 Housing, Air Cleaning Unit: Side-Access Type Figure HA-1300-3 Housing, Air Conditioning Unit: Walk-In Type |
| 200 | HA-1400 DEFINITIONS AND TERMS ARTICLE HA-2000 REFERENCED DOCUMENTS ARTICLE HA-3000 MATERIALS HA-3100 ALLOWABLE MATERIALS HA-3110 General Requirements HA-3120 Protective Coatings HA-3200 SPECIAL LIMITATIONS ON MATERIALS HA-3210 Metals |
| 201 | HA-3300 CERTIFICATION OF MATERIAL ARTICLE HA-4000 DESIGN HA-4100 GENERAL DESIGN HA-4200 DESIGN CRITERIA HA-4210 Load Criteria |
| 202 | HA-4220 Stress Criteria HA-4230 Deflection Criteria HA-4240 Other Criteria HA-4241 Vibration Isolation. HA-4242 Provisions for Relative Movement. HA-4243 Tolerances. HA-4244 Housing Attachments. HA-4245 Welded Attachments. Table HA-4212-1 Load Combinations Table HA-4212-1 Load Combinations |
| 203 | HA-4246 Bolted Attachments. HA-4247 Fatigue Considerations. HA-4248 Fire Protection. HA-4300 HOUSING JOINTS AND SEAMS HA-4310 General HA-4320 Housing Joints and Seams HA-4330 Air Cleaning Unit Joints and Seams HA-4340 Air Conditioning and Air Handling Units Housing, Joints and Seams HA-4400 ACCESSORIES HA-4410 Gaskets HA-4420 Access Doors and Panels |
| 204 | HA-4430 Provisions for Testing and Maintenance HA-4440 Miscellaneous |
| 205 | HA-4500 PRESSURE BOUNDARY LEAKAGE HA-4510 General HA-4520 Applicability HA-4530 Evaluation HA-4600 DESIGN SPECIFICATION |
| 206 | ARTICLE HA-5000 INSPECTION AND TESTING HA-5100 GENERAL HA-5110 Scope and Applicability HA-5120 Responsibility for Procedures HA-5200 INSPECTION HA-5210 General Requirements HA-5220 Housings HA-5230 Housing Supports HA-5240 Filter Mounting Frame to Housing Weld Inspection |
| 207 | HA-5300 PRESSURE BOUNDARY LEAKAGE TESTING HA-5310 Allowance for Housing Leakage Rates by Sections HA-5330 Testing Procedures HA-5340 Documentation HA-5350 Acceptance Criteria HA-5400 MOUNTING FRAME TO HOUSING LEAKAGE TEST HA-5500 STRUCTURAL CAPABILITY TEST HA-5600 AIRFLOW DISTRIBUTION TESTS HA-5700 AIR-AEROSOL MIXING UNIFORMITY TESTS |
| 208 | HA-5800 SAMPLING MANIFOLD TESTING HA-5900 AIR CONDITIONING AND AIR HANDLING UNIT TESTING ARTICLE HA-6000 FABRICATION HA-6100 GENERAL HA-6110 Scope and Applicability HA-6120 Materials HA-6130 Control of Installation and Fabrication Process HA-6140 Welding HA-6200 FABRICATION PROCESS HA-6210 Cutting, Forming, Bending, Aligning, and Fitting |
| 209 | HA-6300 MECHANICAL FASTENING HA-6310 General HA-6400 FABRICATION TOLERANCES HA-6410 General HA-6420 Side-Access Housing and Gasket Seal Surfaces HA-6430 Side-Access Housing Filter Fluid Seal Surfaces HA-6500 CLEANING ARTICLE HA-7000 PACKAGING, SHIPPING, RECEIVING, STORAGE, AND HANDLING HA-7100 GENERAL HA-7200 PACKAGING HA-7210 General HA-7220 Protection HA-7300 SHIPPING HA-7400 RECEIVING |
| 210 | HA-7500 STORAGE HA-7510 General HA-7520 Drains and Vents HA-7530 Other Components ARTICLE HA-8000 QUALITY ASSURANCE HA-8100 GENERAL HA-8200 MATERIAL IDENTIFICATION HA-8300 DRAWINGS AND DOCUMENTATION ARTICLE HA-9000 NAMEPLATES AND STAMPING HA-9100 GENERAL HA-9200 STAMPING AND MARKING HA-9210 Housings HA-9220 Housing Accessories |
| 211 | NONMANDATORY APPENDIX HA-A DIVISION OF RESPONSIBILITY Table HA-A-1000-1 Division of Responsibility |
| 212 | NONMANDATORY APPENDIX HA-B ADDITIONAL GUIDELINES FOR HOUSING DESIGN AND CONSTRUCTION ARTICLE HA-B-1000 GUIDELINES HA-B-1100 INTRODUCTION HA-B-1200 GENERAL |
| 214 | NONMANDATORY APPENDIX HA-C MANIFOLD DESIGN GUIDELINES ARTICLE HA-C-1000 TEST MANIFOLDS HA-C-1100 INTRODUCTION HA-C-1200 MANIFOLD REQUIREMENTS FOR IN-PLACE TESTS HA-C-1300 CONSIDERATIONS FOR USE OF PERMANENTLY INSTALLED MANIFOLDS |
| 215 | Figure HA-C-1230-1 Common Configurations Requiring Test Manifolds (Plan A) |
| 216 | Figure HA-C-1230-2 Common Configurations Requiring Test Manifolds (Plan B) |
| 217 | Figure HA-C-1230-3 Common Configurations Requiring Test Manifolds (Plan C) |
| 218 | Figure HA-C-1230-4 Common Configurations Requiring Test Manifolds (Plan D) |
| 219 | Figure HA-C-1230-5 Common Configurations Requiring Test Manifolds (Plan E) |
| 220 | HA-C-1400 INJECTION MANIFOLDS |
| 221 | HA-C-1500 SAMPLE MANIFOLDS |
| 222 | NONMANDATORY APPENDIX HA-D PERFORMANCE TEST FOR QUALIFICATION OF SAMPLING MANIFOLDS ARTICLE HA-D-1000 PERFORMANCE TEST HA-D-1100 PURPOSE HA-D-1200 LIMITS HA-D-1300 TEST REQUIREMENTS HA-D-1400 TEST METHOD |
| 223 | HA-D-1500 ACCEPTANCE CRITERIA HA-D-1600 DOCUMENTATION HA-D-1700 ACCEPTANCE OF RESULTS |
| 224 | SECTION RA REFRIGERATION EQUIPMENT ARTICLE RA-1000 INTRODUCTION RA-1100 SCOPE RA-1200 PURPOSE RA-1300 APPLICABILITY RA-1310 Clarification of Code Applicability RA-1320 Exclusion of Components RA-1400 DEFINITIONS AND TERMS |
| 225 | ARTICLE RA-2000 REFERENCED DOCUMENTS ARTICLE RA-3000 MATERIALS RA-3100 GENERAL MATERIAL REQUIREMENTS RA-3110 Pressure-Retaining Materials RA-3120 Component Support Materials |
| 226 | RA-3130 Materials for Nonmetallic Components RA-3140 Electrical Materials RA-3150 Pump and Compressor Materials RA-3160 Valve, Piping, and Fitting Materials RA-3170 Welding and Brazing Materials ARTICLE RA-4000 DESIGN REQUIREMENTS RA-4100 PURPOSE RA-4200 DESIGN SPECIFICATION |
| 227 | RA-4300 EQUIPMENT PERFORMANCE REQUIREMENTS RA-4400 MECHANICAL DESIGN REQUIREMENTS RA-4410 Waterside System |
| 228 | RA-4420 Refrigerant Side System RA-4430 Lubrication System RA-4500 STRUCTURAL DESIGN REQUIREMENTS RA-4510 General |
| 229 | RA-4520 Equipment Attachment Boundary RA-4600 ELECTRICAL DESIGN REQUIREMENTS RA-4610 Electric Motors RA-4620 Electric Valve and Vane Actuators RA-4630 Control Systems RA-4640 Electrical Wiring, Splices, and Connections RA-4700 MAINTENANCE CRITERIA |
| 230 | ARTICLE RA-5000 INSPECTION, RATING, AND TESTING RA-5100 RATING RA-5200 TESTING RA-5210 Pressure Vessel Testing |
| 231 | RA-5220 Functional Testing of Motors |
| 232 | RA-5300 EXAMINATION RA-5310 Nondestructive Examination ARTICLE RA-6000 FABRICATION AND INSTALLATION RA-6100 WELDING AND BRAZING RA-6110 Welding RA-6120 Brazing RA-6130 Welding and Brazing of Non-ASME BPVC Pressure-Retaining Components and Supports |
| 233 | RA-6200 CLEANING, FINISHING, AND COATING RA-6210 Cleanliness RA-6220 Cleaning and Finishing RA-6230 Finishing and Surface Preparation RA-6240 Coating and Application |
| 234 | RA-6300 INSTALLATION ARTICLE RA-7000 PACKAGING, SHIPPING, STORAGE, ANDHANDLING RA-7100 GENERAL REQUIREMENTS RA-7200 PACKAGING RA-7210 ASME BPVC, Section III Equipment RA-7220 ASME BPVC, Section VIII Equipment RA-7230 Motors Shipped Separately RA-7300 SHIPPING RA-7310 ASME BPVC Section III Equipment |
| 235 | RA-7320 ASME BPVC, Section VIII Equipment RA-7400 STORAGE RA-7410 ASME BPVC, Section III Equipment RA-7420 ASME BPVC, Section VIII Equipment RA-7500 HANDLING AND RIGGING RA-7510 ASME BPVC, Section III Equipment RA-7520 ASME BPVC Section VIII Equipment |
| 236 | RA-7600 ASSEMBLY, ERECTION, AND START-UP RA-7610 Field-Assembled or Field-Erected Equipment RA-7620 External Connections and Services RA-7630 Start-Up and Periodic Testing ARTICLE RA-8000 QUALITY ASSURANCE RA-8100 GENERAL ARTICLE RA-9000 NAMEPLATES, STAMPING, AND RECORDS RA-9100 GENERAL REQUIREMENTS RA-9200 NAMEPLATES AND STAMPING RA-9300 DATA REPORTS |
| 237 | Forms FORM RA-1 CENTRIFUGAL COMPRESSOR TEST RECORD |
| 238 | FORM RA-1a CENTRIFUGAL COMPRESSOR OIL PUMP PRESSURE TEST |
| 239 | FORM RA-1b CENTRIFUGAL COMPRESSOR PRESSURE TEST RECORD |
| 240 | FORM RA-2 RECIPROCATING SCROLL/SCREW COMPRESSOR TEST RECORD |
| 241 | FORMRA-2a RECIPROCATING SCROLL/SCREWCOMPRESSOR PRESSURE TEST RECORD |
| 242 | FORM RA-3 ELECTRICAL TEST RECORD — CONTROLS AND CONTROL PANELS |
| 243 | FORM RA-4 PERFORMANCE TEST RECORD (U.S. CUSTOMARY) (See Mandatory Appendix RA-I) |
| 245 | FORM RA-M4 PERFORMANCE TEST RECORD (SI) (See Mandatory Appendix RA-MI) |
| 247 | MANDATORY APPENDIX RA-I PERFORMANCE TESTING OF CHILLED WATER REFRIGERATION UNIT (U.S. CUSTOMARY) ARTICLE RA-I-1000 GENERAL RA-I-1100 TEST CONDITIONS RA-I-1200 EFFECT OF FOULING FACTOR RA-I-1300 HEAT BALANCE EQUATION RA-I-1400 MEASURED HEAT BALANCE RA-I-1500 TABULATION OF CAPACITY RA-I-1600 POWER INPUT RA-I-1700 REFRIGERATION MACHINES EQUIPPED WITH SUBCOOLERS |
| 248 | Table RA-I-1100-1 Test Conditions Table RA-I-1200-1 Effect of Fouling Factor Table RA-I-1300-1 Heat Balance Equation |
| 249 | Table RA-I-1500-1 Tabulation of Capacity |
| 250 | MANDATORY APPENDIX RA-MI PERFORMANCE TESTING OF CHILLED WATER REFRIGERATION UNIT (SI) ARTICLE RA-MI-1000 GENERAL RA-MI-1100 TEST CONDITIONS RA-MI-1200 EFFECT OF FOULING FACTOR RA-MI-1300 HEAT BALANCE EQUATION RA-MI-1400 MEASURED HEAT BALANCE RA-MI-1500 TABULATION OF CAPACITY RA-MI-1600 POWER INPUT RA-MI-1700 REFRIGERATION MACHINES EQUIPPED WITH SUBCOOLERS |
| 251 | Table RA-MI-1100-1 Test Conditions Table RA-MI-1200-1 Effect of Fouling Factor |
| 252 | Table RA-MI-1300-1 Heat Balance Equation Table RA-MI-1500-1 Tabulation of Capacity |
| 253 | MANDATORY APPENDIX RA-II MANDATORY LIST OF INSTRUMENTATION FUNCTIONS AND CONTROL FUNCTIONS Table RA-II-1000-1 Mandatory List of Instrumentation Functions and Control Functions |
| 254 | NONMANDATORY APPENDIX RA-A DIVISION OF RESPONSIBILITY |
| 255 | Table RA-A-1000-1 Division of Responsibility |
| 257 | NONMANDATORY APPENDIX RA-B TYPICAL EXTERNAL INTERFACE DIAGRAMS Figure RA-B-1000- 1Interface Points — Typical Two-Vessel Design |
| 258 | SECTION CA CONDITIONING EQUIPMENT ARTICLE CA-1000 INTRODUCTION CA-1100 SCOPE CA-1200 PURPOSE CA-1300 APPLICABILITY CA-1310 Clarification of Code Applicability CA-1320 Exclusion of Components CA-1330 Interfacing Boundaries CA-1400 DEFINITIONS AND TERMS CA-1410 General CA-1420 Water, Steam, and Volatile Refrigerant Coils CA-1440 Electric Heating Coils |
| 259 | ARTICLE CA-2000 REFERENCED DOCUMENTS ARTICLE CA-3000 MATERIALS CA-3100 MATERIAL SPECIFICATIONS CA-3200 WATER, STEAM, AND VOLATILE REFRIGERANT COIL MATERIALS CA-3210 Pressure-Retaining Materials for Water and Steam Coils CA-3220 Pressure-Retaining Materials for Volatile Refrigerant Coils CA-3230 Non-Pressure-Retaining Materials |
| 260 | CA-3240 Load-Bearing Members CA-3250 Non-Load-Carrying Members CA-3400 ELECTRIC HEATING COIL MATERIALS CA-3500 CERTIFICATION OF MATERIALS ARTICLE CA-4000 DESIGN CA-4100 DESIGN CONDITIONS FOR WATER AND STEAM COILS CA-4110 Design Specification |
| 261 | CA-4120 Technical Requirements |
| 262 | CA-4130 Structural Requirements for Water, Steam, and Volatile Refrigerant Coils Table CA-4122-1 Maximum Water Velocities in Water Coils |
| 263 | CA-4200 DESIGN CONDITIONS FOR VOLATILE REFRIGERANT COILS CA-4210 Design Specification CA-4220 Technical Requirements |
| 264 | CA-4400 DESIGN CONDITIONS FOR ELECTRIC HEATING COILS CA-4410 Design Specification CA-4420 Technical Requirements |
| 265 | CA-4430 Structural Requirements for Electric Heating Coils |
| 266 | ARTICLE CA-5000 INSPECTION AND TESTING CA-5100 GENERAL REQUIREMENTS CA-5200 TESTING OF WATER, STEAM, AND VOLATILE REFRIGERANT COILS CA-5210 Performance Verification and Validation |
| 267 | CA-5220 Pressure Testing for Water and Steam Coils CA-5230 Pressure Testing for Volatile Refrigerant Coils CA-5240 Nondestructive Examination CA-5400 TESTING OF ELECTRIC HEATING COILS CA-5410 General Requirements CA-5420 Functional Test CA-5430 Dielectric Withstand Test CA-5440 Resistance Test |
| 268 | CA-5450 Nondestructive Examination CA-5500 TEST REPORTS ARTICLE CA-6000 FABRICATION AND INSTALLATION CA-6100 GENERAL REQUIREMENTS CA-6110 Introduction CA-6120 Welding CA-6130 Brazing CA-6140 Mechanical Joining CA-6200 CLEANING, FINISHING, AND COATING CA-6210 Cleaning and Finishing |
| 269 | CA-6220 Finishing and Surface Preparation CA-6230 Coating and Application ARTICLE CA-7000 PACKAGING, SHIPPING, STORAGE, AND HANDLING CA-7100 GENERAL REQUIREMENTS CA-7200 PACKAGING CA-7210 ASME BPVC, Section III Coils CA-7220 ASME BPVC, Section VIII Coils |
| 270 | CA-7230 Electric Heating Coils CA-7300 SHIPPING CA-7310 ASME BPVC, Section III Coils CA-7320 ASME BPVC, Section VIII Coils CA-7330 Electric Heating Coils CA-7400 STORAGE CA-7410 ASME BPVC, Section III Coils CA-7420 ASME BPVC, Section VIII Coils CA-7430 Electric Heating Coils CA-7500 HANDLING CA-7510 ASME BPVC, Section III Coils CA-7520 ASME BPVC, Section VIII Coils CA-7530 Electric Heaters ARTICLE CA-8000 QUALITY ASSURANCE CA-8100 GENERAL REQUIREMENTS CA-8110 Introduction |
| 271 | CA-8120 Documentation and Retention Table CA-8121-1 Lifetime Quality Assurance Records Table CA-8121-2 Nonpermanent Quality Assurance Records |
| 272 | ARTICLE CA-9000 NAMEPLATES AND RECORDS CA-9100 GENERAL REQUIREMENTS CA-9200 COILS CA-9300 INFORMATION ON NAMEPLATES CA-9310 Water, Steam, and Volatile Refrigerant Coils CA-9320 Electric Heating Coils CA-9400 NAMEPLATE VISIBILITY CA-9500 DATA REPORTS CA-9510 Coils CA-9520 Volatile Refrigerant Coils ARTICLE CA-10000 REPAIRS AND REPLACEMENTS CA-10100 GENERAL |
| 273 | NONMANDATORY APPENDIX CA-A DIVISION OF RESPONSIBILITY Table CA-A-1000-1 Division of Responsibility |
| 274 | NONMANDATORY APPENDIX CA-B DESIGN RECOMMENDATIONS ARTICLE CA-B-1000 RECOMMENDED DESIGN CRITERIA FOR WATER, STEAM, AND VOLATILE REFRIGERANT COILS CA-B-1100 SCOPE CA-B-1200 GENERAL RECOMMENDATIONS |
| 275 | SECTION FA MOISTURE SEPARATORS ARTICLE FA-1000 INTRODUCTION FA-1100 SCOPE FA-1200 PURPOSE FA-1300 APPLICABILITY FA-1310 Moisture Separators FA-1320 Limitations FA-1400 DEFINITIONS AND TERMS ARTICLE FA-2000 REFERENCED DOCUMENTS ARTICLE FA-3000 MATERIALS FA-3100 ALLOWABLE MATERIALS FA-3110 Pads FA-3120 Filter Cases, Cross Grids, and Supports FA-3130 Rivets FA-3140 Gaskets FA-3150 Adhesive FA-3200 LIMITATIONS |
| 276 | FA-3300 MATERIAL CERTIFICATION ARTICLE FA-4000 DESIGN FA-4100 GENERAL DESIGN FA-4200 TECHNICAL REQUIREMENTS FA-4210 Design Requirements FA-4220 Moisture Separator Assembly FA-4300 STRUCTURAL REQUIREMENTS FA-4310 General FA-4320 Load Definition FA-4330 Load Combinations FA-4340 Acceptance Criteria ARTICLE FA-5000 INSPECTION AND TESTING FA-5100 QUALIFICATION TESTS FA-5110 Moisture Separator Rough Handling Qualifications FA-5120 Moisture Separator Airflow Resistance Test |
| 277 | Figure FA-4100-1 Typical Moisture Separation Configuration Table FA-4100-1 Moisture Separator Performance Specifications |
| 278 | FA-5130 Moisture Separator Performance Test FA-5140 Certification FA-5200 PRODUCTION INSPECTION AND TESTING FA-5210 Dimensional Inspection FA-5220 Welding Inspection FA-5230 Moisture Separator Airflow Resistance Test ARTICLE FA-6000 FABRICATION FA-6100 REPAIRS FA-6200 CLEANING FA-6300 TOLERANCES FA-6310 Flatness and Squareness FA-6320 Overall Dimensions ARTICLE FA-7000 PACKAGING, SHIPPING, AND STORAGE ARTICLE FA-8000 QUALITY ASSURANCE |
| 279 | FA-8100 RESPONSIBILITY FA-8200 DOCUMENTATION FA-8300 CERTIFICATE OF CONFORMANCE ARTICLE FA-9000 NAMEPLATES FA-9100 MOISTURE SEPARATOR MARKING FA-9200 PACKAGE MARKING |
| 280 | NONMANDATORY APPENDIX FA-A DIVISION OF RESPONSIBILITY Table FA-A-1000-1 Division of Responsibility |
| 281 | SECTION FB MEDIUM EFFICIENCY PARTICULATE AIR FILTERS ARTICLE FB-1000 INTRODUCTION FB-1100 SCOPE FB-1200 PURPOSE FB-1300 APPLICABILITY FB-1310 Limitations FB-1320 Responsibility FB-1400 DEFINITIONS AND TERMS ARTICLE FB-2000 REFERENCED DOCUMENTS |
| 282 | ARTICLE FB-3000 MATERIALS FB-3100 ALLOWABLE MATERIALS FB-3110 Filter Medium FB-3120 Filter Case FB-3130 Separators FB-3140 Sealants and Adhesives FB-3150 Gaskets FB-3200 SPECIAL LIMITATIONS OF MATERIALS ARTICLE FB-4000 DESIGN FB-4100 GENERAL DESIGN FB-4200 DESIGN CRITERIA FB-4300 STRUCTURAL REQUIREMENTS ARTICLE FB-5000 INSPECTION AND TESTING FB-5100 INSPECTION PLAN FB-5110 Minimum Inspection Requirements |
| 283 | FB-5120 Rejection and Reinspection FB-5200 QUALIFICATION TESTING FB-5210 Testing Requirements FB-5220 Certification FB-5230 Seismic Qualification ARTICLE FB-6000 FABRICATION FB-6100 GENERAL FB-6210 Flatness and Squareness FB-6220 Overall Dimensions FB-6300 WORKMANSHIP ARTICLE FB-7000 PACKAGING, SHIPPING, AND STORAGE FB-7100 GENERAL |
| 284 | ARTICLE FB-8000 QUALITY ASSURANCE FB-8100 GENERAL FB-8200 DOCUMENTATION FB-8300 CERTIFICATE OF CONFORMANCE ARTICLE FB-9000 LABELS AND MARKINGS FB-9100 FILTER LABELS AND MARKINGS FB-9200 PACKAGE MARKING |
| 285 | NONMANDATORY APPENDIX FB-A DIVISION OF RESPONSIBILITY Table FB-A-1000-1 Division of Responsibility |
| 286 | NONMANDATORY APPENDIX FB-B REPLACEMENT OF FB MEDIUM EFFICIENCY PARTICULATE AIR FILTERS |
| 287 | SECTION FC HEPA FILTERS ARTICLE FC-1000 INTRODUCTION FC-1100 SCOPE FC-1200 PURPOSE FC-1300 APPLICABILITY FC-1310 HEPA Filters FC-1320 Limitations FC-1400 DEFINITIONS AND TERMS ARTICLE FC-2000 REFERENCED DOCUMENTS |
| 288 | ARTICLE FC-3000 MATERIALS FC-3100 ALLOWABLE MATERIALS FC-3110 Case Materials FC-3120 Gasket Materials FC-3130 Filter Media FC-3140 Faceguards FC-3150 Adhesives FC-3160 Separators |
| 289 | ARTICLE FC-4000 DESIGN |
| 290 | Figure FC-4110-1 Type A, Type C, or Type D Metal-Cased, Gasket-Sealed Filter Figure FC-4110-2 Type A Wood Case Separator Filter |
| 291 | Figure FC-4110-3 Type B Mini Pleat Filter Figure FC-4110-4 Type C Separatorless Filter |
| 292 | Figure FC-4110-5 Type D Thread Separator Filter Table FC-4110-1 Nominal Sizes and Ratings |
| 294 | FC-4210 Test Aerosol Particle Penetration FC-4220 Resistance to Airflow FC-4300 SEISMIC QUALIFICATION ARTICLE FC-5000 INSPECTION AND TESTING FC-5100 QUALIFICATION TESTING Figure FC-4142-1 Gel Seal Filter Corner — Isometric |
| 295 | FC-5110 Resistance to Airflow FC-5120 Test Aerosol Particle Penetration Table FC-5100-1 Test Groups and Sequence Table FC-5120-1 Acceptable Test |
| 296 | FC-5130 Resistance to Rough Handling FC-5140 Resistance to Pressure FC-5150 Resistance to Heated Air FC-5160 Spot Flame Resistance Table FC-5140-1 Test Conditions and Requirements |
| 297 | FC-5170 Structural Requirements FC-5200 INSPECTION FC-5300 PRODUCTION TESTING ARTICLE FC-6000 FABRICATION FC-6100 GENERAL REQUIREMENTS FC-6200 MANUFACTURE AND ASSEMBLY FC-6210 Tolerances FC-6220 Medium Installation FC-6300 WORKMANSHIP ARTICLE FC-7000 PACKAGING, SHIPPING, AND STORAGE ARTICLE FC-8000 QUALITY ASSURANCE FC-8100 RESPONSIBILITY |
| 298 | FC-8200 CERTIFICATE OF CONFORMANCE ARTICLE FC-9000 LABELS AND MARKINGS FC-9100 FILTER MARKING FC-9200 PACKAGE MARKING |
| 299 | NONMANDATORY APPENDIX FC-A DIVISION OF RESPONSIBILITY Table FC-A-1000-1 Division of Responsibility |
| 300 | SECTION FD TYPE II ADSORBER CELLS ARTICLE FD-1000 INTRODUCTION FD-1100 SCOPE FD-1200 PURPOSE FD-1300 APPLICABILITY FD-1400 DEFINITIONS AND TERMS ARTICLE FD-2000 REFERENCED DOCUMENTS ARTICLE FD-3000 MATERIALS FD-3100 ALLOWABLE MATERIALS FD-3110 Adsorbent FD-3120 Screens FD-3130 Casing |
| 301 | FD-3140 Gaskets and Seal Pads FD-3150 Adhesive FD-3160 Threaded Fasteners FD-3170 Rivets FD-3200 LIMITS FD-3300 CERTIFICATION OF MATERIALS FD-3310 Metal Parts FD-3320 Gaskets and Seal Pads FD-3330 Adhesive FD-3340 Threaded Fasteners FD-3350 Hardware Items (Washers and Rivets) ARTICLE FD-4000 DESIGN FD-4100 GENERAL DESIGN FD-4200 TECHNICAL REQUIREMENTS FD-4210 Design Requirements FD-4220 Adsorber Bed FD-4230 Case and Assembly |
| 302 | Figure FD-4100-1 Type II Adsorber Cell |
| 303 | FD-4300 STRUCTURAL REQUIREMENTS FD-4310 General FD-4320 Load Definition FD-4330 Load Combinations FD-4340 Acceptance Criteria ARTICLE FD-5000 INSPECTION AND TESTING FD-5100 DIMENSIONAL INSPECTION FD-5200 WELDING INSPECTION FD-5210 Spot Welds FD-5220 Other Welds FD-5300 QUALIFICATION TESTS |
| 304 | FD-5310 Design Qualification FD-5320 Filling Method Qualification FD-5330 Acceptance Tests ARTICLE FD-6000 FABRICATION FD-6100 DIMENSIONS AND TOLERANCES FD-6200 WELDING AND BRAZING FD-6210 Testing and Inspection Table FD-5332-1 Detector Sensitivity for Leak Test |
| 305 | FD-6220 Repairs FD-6300 FILLING FD-6400 CLEANING ARTICLE FD-7000 PACKAGING AND SHIPPING FD-7100 PACKAGING FD-7200 LOADING FOR SHIPMENT FD-7300 STORAGE FD-7400 CONTAINERS ARTICLE FD-8000 QUALITY ASSURANCE Table FD-6100-1 Cell Dimensions and Tolerances |
| 306 | FD-8100 DOCUMENTATION ARTICLE FD-9000 NAMEPLATES AND CERTIFICATION FD-9100 PERMANENT NAMEPLATE FD-9200 FILLING LABEL |
| 307 | MANDATORY APPENDIX FD-I CALCULATION OF RESIDENCE TIME OF ADSORBER CELLS ARTICLE FD-I-1000 RESIDENCE TIME |
| 308 | MANDATORY APPENDIX FD-II SAMPLE CANISTERS ARTICLE FD-II-1000 INTRODUCTION FD-II-1100 SCOPE FD-II-1200 APPLICABILITY FD-II-1300 DEFINITIONS AND TERMS ARTICLE FD-II-2000 GENERAL DESIGN FD-II-2100 TECHNICAL REQUIREMENTS FD-II-2110 Design Requirements FD-II-2120 Sample Canister Casing FD-II-2130 Assembly |
| 309 | Figure FD-II-2000-1 Examples of Sample Canister Configurations |
| 310 | Figure FD-II-2110-1 Detail of a Typical 2-in. Sample Canister |
| 311 | NONMANDATORY APPENDIX FD-A DIVISION OF RESPONSIBILITY Table FD-A-1000-1 Division of Responsibility |
| 312 | SECTION FE TYPE III ADSORBERS ARTICLE FE-1000 INTRODUCTION FE-1100 SCOPE FE-1200 PURPOSE FE-1300 APPLICABILITY FE-1310 Type III Adsorbers FE-1320 Adsorbents FE-1330 Limitations FE-1340 Responsibility FE-1400 DEFINITIONS AND TERMS ARTICLE FE-2000 REFERENCED DOCUMENTS ARTICLE FE-3000 MATERIALS FE-3100 ALLOWABLE MATERIALS FE-3110 Adsorbent |
| 313 | FE-3120 Screens and Casing FE-3130 Gaskets and Seal Pads FE-3140 Other Components ARTICLE FE-4000 DESIGN FE-4100 GENERAL FE-4110 Type III Adsorbers FE-4120 Adsorber Service Equipment FE-4121 Adsorbent Removal Equipment. FE-4200 TECHNICAL REQUIREMENTS FE-4210 Design Criteria FE-4220 Sizing FE-4300 ADSORBENT BED DETAILS |
| 314 | Figure FE-4110-1 Horizontal Section of Type III Adsorber Bed |
| 315 | FE-4400 STRUCTURAL REQUIREMENTS FE-4410 General FE-4420 Load Definition FE-4430 Load Combinations FE-4440 Acceptance Criteria FE-4500 ADSORBENT HANDLING SUBSYSTEMS FE-4510 Adsorbent Loading System |
| 316 | FE-4520 Adsorbent Removal System FE-4600 AUXILIARY SYSTEMS FE-4610 Sampling of Installed Adsorbents FE-4620 Fire Protection |
| 317 | ARTICLE FE-5000 INSPECTION AND TESTING FE-5100 GENERAL FE-5200 VISUAL INSPECTION FE-5300 DIMENSIONAL INSPECTION FE-5310 Bed Depth FE-5320 Screens FE-5330 Adsorbent Reservoir FE-5400 WELDING INSPECTION FE-5410 Spot Welds FE-5420 Seal Welds |
| 318 | FE-5500 FABRICATION TOLERANCES FE-5600 DESIGN QUALIFICATION FE-5610 Functional Design Qualification FE-5620 Filling Method Qualification FE-5630 Seismic Qualification FE-5700 ACCEPTANCE TESTS ARTICLE FE-6000 FABRICATION AND INSTALLATION FE-6100 GENERAL FE-6200 WELDING FE-6300 CLEANING FE-6400 CONSTRUCTION AND INSTALLATION FE-6500 REPAIRS ARTICLE FE-7000 PACKAGING AND SHIPPING FE-7100 TYPE III ADSORBERS FE-7200 ADSORBENT MATERIALS ARTICLE FE-8000 QUALITY ASSURANCE FE-8100 GENERAL |
| 319 | FE-8200 INSPECTION REPORTS AND DOCUMENTATION ARTICLE FE-9000 NAMEPLATES FE-9100 PERMANENT NAMEPLATES FE-9200 FILLING LABEL |
| 320 | MANDATORY APPENDIX FE-I RESIDENCE TIME CALCULATION ARTICLE FE-I-1000 CALCULATION OF RESIDENCE TIME OF ADSORBERS |
| 321 | MANDATORY APPENDIX FE-II SCREEN WAVINESS INSPECTION TEST ARTICLE FE-II-1000 SCREEN WAVINESS ARTICLE FE-II-2000 PROCEDURE ARTICLE FE-II-3000 ACCEPTANCE CRITERIA |
| 322 | MANDATORY APPENDIX FE-III ADSORBER FILLING QUALIFICATION TEST PROCEDURE ARTICLE FE-III-1000 SCOPE ARTICLE FE-III-2000 PURPOSE ARTICLE FE-III-3000 FILLING METHOD ARTICLE FE-III-4000 PROCEDURE FE-III-4100 ADSORBENT CHARACTERISTICS FE-III-4110 Bed Volume FE-III-4120 Adsorbent Weight FE-III-4130 Particle Size Distribution FE-III-4200 PACKING DENSITY FE-III-4300 ADSORBENT LOSSES |
| 324 | MANDATORY APPENDIX FE-IV TYPE III ADSORBER QUALIFICATION TEST PROCEDURE ARTICLE FE-IV-1000 SCOPE ARTICLE FE-IV-2000 PURPOSE ARTICLE FE-IV-3000 THEORY |
| 325 | ARTICLE FE-IV-4000 EXAMPLE FE-IV-4100 APPARATUS FE-IV-4200 TEST PROCEDURE Figure FE-IV-3000-1 Adsorbate Distribution Curves |
| 326 | FE-IV-4300 RH MEASUREMENT FE-IV-4400 RH BREAKTHROUGH FE-IV-4500 ADSORBENT SAMPLING FE-IV-4600 MOISTURE CONTENT Figure FE-IV-4100-1 Test Adsorber Setup Figure FE-IV-4100-1 Test Adsorber Setup |
| 327 | MANDATORY APPENDIX FE-V SAMPLE CANISTERS ARTICLE FE-V-1000 INTRODUCTION FE-V-1100 SCOPE FE-V-1200 APPLICABILITY FE-V-1300 DEFINITIONS AND TERMS ARTICLE FE-V-2000 GENERAL DESIGN FE-V-2100 TECHNICAL REQUIREMENTS FE-V-2110 Design Requirements FE-V-2120 Sample Canister Casing FE-V-2130 Assembly |
| 329 | NONMANDATORY APPENDIX FE-A VISUAL INSPECTION RECOMMENDATIONS FOR TYPE III ADSORBERS ARTICLE FE-A-1000 GENERAL FE-A-1100 ADSORBER SECTIONS FE-A-1200 ADSORBER ASSEMBLY FE-A-1300 ADSORBER SERVICE SYSTEMS FE-A-1400 INSPECTION OPENINGS FE-A-1500 LABELING |
| 330 | NONMANDATORY APPENDIX FE-B DIVISION OF RESPONSIBILITY Table FE-B-1000-1 Division of Responsibility |
| 331 | SECTION FF ADSORBENT MEDIA ARTICLE FF-1000 INTRODUCTION FF-1100 SCOPE FF-1200 PURPOSE FF-1300 APPLICABILITY FF-1400 DEFINITIONS AND TERMS ARTICLE FF-2000 REFERENCED DOCUMENTS |
| 332 | ARTICLE FF-3000 MATERIALS ARTICLE FF-4000 DESIGN FF-4100 GENERAL DESIGN FF-4200 ADSORBENT DEGRADATION FF-4210 Desorption FF-4220 Degradation ARTICLE FF-5000 INSPECTION AND TESTING FF-5100 PHYSICAL TESTING FF-5110 Before Impregnation FF-5120 After Impregnation |
| 333 | FF-5200 RADIOACTIVE TESTING FF-5210 Qualification Tests FF-5220 Radioactive Batch Tests FF-5300 ACCEPTABLE ASTM STANDARDS ARTICLE FF-6000 FABRICATION ARTICLE FF-7000 PACKAGING AND SHIPPING FF-7100 PROTECTION OF ADSORBENT MEDIA FF-7200 STORAGE |
| 334 | FF-7300 CONTAINERS ARTICLE FF-8000 QUALITY ASSURANCE FF-8100 DOCUMENTATION ARTICLE FF-9000 NAMEPLATES AND CERTIFICATION |
| 335 | NONMANDATORY APPENDIX FF-A DIVISION OF RESPONSIBILITY Table FF-A-1000-1 Division of Responsibility |
| 336 | SECTION FG MOUNTING FRAMES FOR AIR-CLEANING EQUIPMENT ARTICLE FG-1000 INTRODUCTION FG-1100 SCOPE FG-1200 LIMITATIONS FG-1300 PURPOSE FG-1400 RESPONSIBILITY ARTICLE FG-2000 REFERENCED DOCUMENTS ARTICLE FG-3000 MATERIALS FG-3100 ALLOWABLE MATERIALS FG-3200 MATERIAL LIMITATIONS ARTICLE FG-4000 DESIGN FG-4100 GENERAL DESIGN FG-4110 HEPA Filter Mounting Frames |
| 337 | FG-4120 Type II Adsorber Cell Mounting Frames Figure FG-4110-1 Typical Filter Mounting Frame |
| 338 | Figure FG-4120-1 Typical Type II Adsorber Mounting Frame |
| 339 | FG-4130 Medium Efficiency Filter Mounting Frames FG-4140 Moisture Separator Mounting Frames Figure FG-4140-1 Typical Moisture Separator Mounting Frame |
| 340 | FG-4150 Common Requirements FG-4200 STRUCTURAL REQUIREMENTS FG-4210 General FG-4220 Load Definition FG-4230 Load Combinations FG-4240 Acceptance Criteria FG-4300 STRUCTURAL DESIGN ANALYSIS FG-4310 Filter Mounting Frame Deflection Limits |
| 341 | FG-4320 Type II Adsorber Cell and Moisture Separator Mounting Frame Deflection Limits FG-4330 Pressure Impulse Loading ARTICLE FG-5000 INSPECTION AND TESTING FG-5100 DIMENSIONAL INSPECTION FG-5200 ALIGNMENT AND SURFACE FINISH FOR HEPA FILTER AND TYPE II ADSORBER CELL MOUNTING FRAMES FG-5210 HEPA Filter and Type II Adsorber Cell Mounting Frame Alignment FG-5211 Perpendicularity. FG-5212 Planarity of Adjoining Members. FG-5220 HEPA Filter and Type II Adsorber Cell Mounting Frame Flatness |
| 342 | FG-5230 HEPA Filter and Type II Adsorber Cell Mounting Frame Dimensions FG-5240 HEPA Filter and Type II Adsorber Cell Mounting Frame Surface Finish FG-5300 ALIGNMENT AND SURFACE FINISH FOR MEDIUM EFFICIENCY FILTER AND MOISTURE SEPARATOR MOUNTING FRAMES FG-5310 Medium Efficiency Filter and Moisture Separator Mounting Frame Alignment FG-5311 Perpendicularity. FG-5312 Planarity of Adjoining Members. FG-5320 Medium Efficiency Filter and Moisture Separator Mounting Frame Flatness FG-5330 Medium Efficiency Filter and Moisture Separator Mounting Frame Dimensions FG-5340 Medium Efficiency Filter and Moisture Separator Mounting Frame Surface Finish FG-5400 WELD INSPECTION FG-5500 COATING INSPECTION ARTICLE FG-6000 FABRICATION FG-6100 GENERAL FG-6200 WELDING FG-6300 CLAMPING DEVICES FG-6400 CLEANING FG-6500 COATING |
| 344 | NONMANDATORY APPENDIX FG-A DIVISION OF RESPONSIBILITY |
| 345 | Table FG-A-1000-1 Division of Responsibility |
| 347 | SECTION FH OTHER ADSORBERS ARTICLE FH-1000 INTRODUCTION FH-1100 SCOPE FH-1200 PURPOSE FH-1300 APPLICABILITY FH-1400 DEFINITIONS AND TERMS ARTICLE FH-2000 REFERENCED DOCUMENTS ARTICLE FH-3000 MATERIALS FH-3100 ALLOWABLE MATERIALS FH-3110 Adsorbent FH-3120 Screens FH-3130 Casing FH-3140 Adhesives and Sealants FH-3150 Rivets FH-3200 LIMITS FH-3300 CERTIFICATION OF MATERIALS |
| 348 | FH-3310 Fabricated Metal Parts FH-3320 Gaskets and Seal Pads FH-3330 Adhesives and Sealants FH-3340 Purchased Hardware Items (Washers and Rivets) ARTICLE FH-4000 DESIGN FH-4100 GENERAL DESIGN FH-4200 TECHNICAL REQUIREMENTS FH-4210 Design Requirements FH-4211 Residence Time Requirements. FH-4212 Residence Time Calculation. FH-4220 Adsorber Beds FH-4230 Case and Assembly |
| 349 | Figure FH-4100-1 Type IV “V” Adsorbers Model (Fluid Seal Version) Figure FH-4100-1 Type IV “V” Adsorbers Model (Fluid Seal Version) |
| 350 | Figure FH-4100-2 Type IV “V” Bed Adsorbers Model (Gasketed Version) Figure FH-4100-2 Type IV “V” Bed Adsorbers Model (Gasketed Version) |
| 351 | Figure FH-4100-3 Type IV “V” Adsorbers Model, Exploded View Figure FH-4100-3 Type IV “V” Adsorbers Model, Exploded View |
| 352 | FH-4240 Gaskets FH-4241 Material. FH-4242 Adhesive Seal. FH-4250 Gel Seals Figure FH-4100-4 Type IV “U” Bed Adsorbers Model (Gasketed Version) Figure FH-4100-4 Type IV “U” Bed Adsorbers Model (Gasketed Version) |
| 353 | FH-4300 STRUCTURAL REQUIREMENTS FH-4310 General FH-4320 Load Definition FH-4330 Load Combinations FH-4340 Acceptance Criteria ARTICLE FH-5000 INSPECTION AND TESTING FH-5100 DIMENSIONAL INSPECTION FH-5200 WELDING INSPECTION FH-5210 Spot Welds FH-5220 Other Welds FH-5300 QUALIFICATION TESTS FH-5310 Filling Method Qualification |
| 354 | FH-5400 ACCEPTANCE TESTS FH-5410 Airflow Resistance Test FH-5420 Refrigerant Leak Test ARTICLE FH-6000 FABRICATION FH-6100 DIMENSIONS AND TOLERANCES FH-6200 WELDING FH-6210 Testing and Inspection FH-6220 Repairs Table FH-6100-1 Dimensional Requirements |
| 355 | FH-6300 FILLING FH-6400 CLEANING ARTICLE FH-7000 PACKAGING AND SHIPPING FH-7100 PACKAGING FH-7200 LOADING FOR SHIPMENT FH-7300 STORAGE FH-7400 CONTAINERS ARTICLE FH-8000 QUALITY ASSURANCE FH-8100 DOCUMENTATION ARTICLE FH-9000 NAMEPLATES AND CERTIFICATION FH-9100 PERMANENT NAMEPLATE |
| 356 | FH-9200 FILLING LABEL |
| 357 | NONMANDATORY APPENDIX FH-A DIVISION OF RESPONSIBILITY Table FH-A-1000-1 Division of Responsibility |
| 358 | SECTION FI METAL MEDIA FILTERS |
| 359 | SECTION FJ LOW EFFICIENCY PARTICULATE AIR FILTERS ARTICLE FJ-1000 INTRODUCTION FJ-1100 SCOPE FJ-1200 PURPOSE FJ-1300 APPLICABILITY FJ-1310 Limitations FJ-1320 Responsibility FJ-1400 DEFINITIONS AND TERMS ARTICLE FJ-2000 REFERENCED DOCUMENTS ARTICLE FJ-3000 MATERIALS FJ-3100 ALLOWABLE MATERIALS FJ-3110 Filter Medium |
| 360 | FJ-3120 Filter Case FJ-3130 Separators FJ-3140 Sealants and Adhesives FJ-3150 Gaskets FJ-3200 SPECIAL LIMITATIONS OF MATERIALS ARTICLE FJ-4000 DESIGN FJ-4100 GENERAL DESIGN FJ-4200 DESIGN CRITERIA FJ-4300 STRUCTURAL REQUIREMENTS ARTICLE FJ-5000 INSPECTION AND TESTING FJ-5100 INSPECTION PLAN FJ-5110 Minimum Inspection Requirements FJ-5120 Rejection and Reinspection FJ-5200 QUALIFICATION TESTING |
| 361 | FJ-5210 Testing Requirements FJ-5220 Certification FJ-5230 Seismic Qualification ARTICLE FJ-6000 FABRICATION FJ-6100 GENERAL FJ-6200 MANUFACTURE AND ASSEMBLY FJ-6210 Tolerances ARTICLE FJ-7000 PACKAGING, SHIPPING, AND STORAGE FJ-7100 GENERAL ARTICLE FJ-8000 QUALITY ASSURANCE FJ-8100 GENERAL FJ-8200 DOCUMENTATION FJ-8300 CERTIFICATE OF CONFORMANCE ARTICLE FJ-9000 LABELS AND MARKINGS FJ-9100 FILTER LABELS AND MARKINGS |
| 362 | FJ-9200 PACKAGE MARKING |
| 363 | NONMANDATORY APPENDIX FJ-A DIVISION OF RESPONSIBILITY Table FJ-A-1000-1 Division of Responsibility |
| 364 | NONMANDATORY APPENDIX FJ-B REPLACEMENT OF FJ LOW EFFICIENCY PARTICULATE AIR FILTERS |
| 365 | SECTION FK SPECIAL HEPA FILTERS ARTICLE FK-1000 INTRODUCTION FK-1100 SCOPE FK-1200 PURPOSE FK-1300 APPLICABILITY FK-1310 Special HEPA Filters FK-1320 Limitations FK-1330 Service Life FK-1340 Division of Responsibility FK-1400 DEFINITIONS AND TERMS |
| 366 | ARTICLE FK-2000 REFERENCED DOCUMENTS ARTICLE FK-3000 MATERIALS FK-3100 ALLOWABLE MATERIALS FK-3110 Cases, End Caps, Grilles, and Flange Materials |
| 367 | FK-3120 Gasket Material FK-3130 Filter Media FK-3140 Face guards FK-3150 Adhesives FK-3160 Separators FK-3170 Grilles FK-3200 GENERAL MATERIAL REQUIREMENTS FK-3210 Special Limitations of Materials |
| 368 | FK-3220 Alternate Materials ARTICLE FK-4000 DESIGN FK-4100 GENERAL DESIGN FK-4110 Special HEPA Filters Table FK-4111-1 Type 1 Radial Flow HEPA Filter — Nominal Rating |
| 369 | Figure FK-4111-1 Type 1 Radial Flow HEPA Filter (Internal Gasket), Midsection View |
| 370 | Figure FK-4111-2 Type 1 Radial Flow HEPA Filter (Internal Gelatinous Seal), Midsection View |
| 371 | Figure FK-4111-3 Type 1 Radial Flow HEPA Filter (External Gasket), Midsection View |
| 372 | Figure FK-4111-4 Type 1 Radial Flow HEPA Filter (External Gelatinous Seal), Midsection View |
| 373 | Figure FK-4112-1 Type 2 Axial Flow Circular HEPA Filters |
| 374 | FK-4120 Filter End Cap, Grilles, and Flange FK-4130 Filter Pack FK-4140 Gaskets Table FK-4112-1 Type 2 Axial Flow CircularHEPAFilter — Nominal Rating |
| 375 | FK-4150 Grilles FK-4160 Face guards FK-4170 Separators FK-4200 PERFORMANCE REQUIREMENTS FK-4300 STRUCTURAL REQUIREMENTS ARTICLE FK-5000 QUALIFICATION, INSPECTION, AND PRODUCTION TESTING FK-5100 QUALIFICATION TESTING FOR TYPE 1 RADIAL FLOW FILTERS |
| 376 | FK-5110 Resistance to Airflow FK-5120 Test Aerosol Particle Penetration Table FK-4200-1 Performance Requirements |
| 377 | FK-5130 Resistance to Rough Handling FK-5140 Resistance to Pressure FK-5150 Resistance to Heated Air FK-5160 Spot Flame Resistance Table FK-5100-1 Test Groups and Sequence — Type 1 Radial Flow HEPA Filters Table FK-5100-1 Test Groups and Sequence — Type 1 Radial Flow HEPA Filters |
| 378 | FK-5200 QUALIFICATION TESTING FOR TYPE 2 AXIAL FLOW CIRCULAR FILTERS Table FK-5140-1 Test Conditions and Requirements Table FK-5200-1 Test Groups and Sequence — Type 2 Axial Flow Circular HEPA Filters |
| 379 | FK-5210 Resistance to Airflow FK-5220 Test Aerosol Particle Penetration FK-5230 Resistance to Rough Handling FK-5240 Resistance to Pressure |
| 380 | FK-5250 Resistance to Heated Air FK-5260 Spot Flame Resistance FK-5400 QUALIFICATION TESTING FOR TYPE 4 AXIAL FLOW RECTANGULAR FILTERS |
| 381 | FK-5410 Resistance to Airflow FK-5420 Test Aerosol Particle Penetration FK-5430 Resistance to Rough Handling FK-5440 Resistance to Pressure Table FK-5400-1 Test Groups and Sequence — Type 4 Axial Flow Rectangular HEPA Filters |
| 382 | FK-5450 Resistance to Heated Air FK-5460 Spot Flame Resistance FK-5500 INSPECTION FK-5600 PRODUCTION TESTING ARTICLE FK-6000 FABRICATION FK-6100 GENERAL FK-6200 MANUFACTURE AND ASSEMBLY FK-6210 Tolerances |
| 383 | FK-6220 Media Installation FK-6300 WORKMANSHIP ARTICLE FK-7000 PACKAGING, SHIPPING, AND STORAGE ARTICLE FK-8000 QUALITY ASSURANCE FK-8100 RESPONSIBILITY FK-8200 CERTIFICATE OF CONFORMANCE ARTICLE FK-9000 NAMEPLATES FK-9100 FILTER MARKING FK-9200 PACKAGE MARKING |
| 384 | NONMANDATORY APPENDIX FK-A DETERMINATION OF HEPA FILTER SERVICE LIFE |
| 385 | NONMANDATORY APPENDIX FK-B DIVISION OF RESPONSIBILITY Table FK-B-1000-1 Division of Responsibility |
| 386 | SECTION FL DEEP BED SAND FILTERS ARTICLE FL-1000 INTRODUCTION FL-1100 SCOPE FL-1200 PURPOSE FL-1300 APPLICABILITY FL-1310 Limitations FL-1320 Division of Responsibility FL-1400 DEFINITIONS AND TERMS ARTICLE FL-2000 REFERENCED DOCUMENTS |
| 387 | ARTICLE FL-3000 MATERIALS FL-3100 ALLOWABLE MATERIALS FL-3110 General Requirements FL-3120 Filter Media FL-3130 DBS Filter Structure and Distribution Channels FL-3140 Distribution Support Structure FL-3150 Monitoring, Sampling, and Instrumentation Lines |
| 388 | FL-3160 Gaskets FL-3200 SPECIAL LIMITATIONS OF MATERIALS FL-3300 CERTIFICATION OF MATERIALS ARTICLE FL-4000 DESIGN FL-4100 GENERAL DEEP BED SAND FILTER DESIGN FL-4110 DBS Filter Design FL-4120 General Arrangement FL-4200 DESIGN CRITERIA |
| 389 | FL-4210 Design Features Figure FL-4120-1 Typical DBS Filter Cross Section, DOE-HDBK-1169-2003 |
| 390 | FL-4220 Monitoring Capabilities FL-4230 Particle Removal Efficiency FL-4300 STRUCTURAL REQUIREMENTS FL-4310 General FL-4320 Natural Phenomena ARTICLE FL-5000 INSPECTION AND TESTING FL-5100 ACCEPTANCE TESTS FL-5110 Filter Media Acceptance Tests |
| 391 | FL-5120 Distribution Support Structure Acceptance Tests FL-5130 DBS Filter Structure Acceptance Tests FL-5200 INSPECTION PLAN FL-5210 Plan FL-5220 Minimum Filter Media Inspection Requirements FL-5230 Minimum Distribution Support Structure Inspection Requirements |
| 392 | FL-5240 Minimum Monitoring and Sampling Line Inspection Requirements FL-5250 Minimum DBS Filter Structure Inspection Requirements FL-5260 Rejection and Reinspection FL-5300 QUALIFICATION AND VERIFICATION TESTING FL-5310 Filter Media Verification Testing FL-5320 DBS Filter Performance Qualification and Verification Testing ARTICLE FL-6000 FABRICATION/FIELD CONSTRUCTION FL-6100 GENERAL |
| 393 | FL-6200 FABRICATION AND ASSEMBLY FL-6210 Reinforcing Steel and Concrete FL-6220 Distribution Support Structure FL-6230 Structural Steel FL-6300 INSTALLATION FL-6310 Concrete Installation FL-6320 Distribution Support Structure Installation FL-6330 Monitoring and Sampling Line Installation FL-6340 Structural Steel Installation FL-6350 Filter Media Installation FL-6400 TOLERANCES FL-6410 Concrete Tolerances FL-6420 Distribution Support Structure Tolerances FL-6430 Monitoring and Sampling Line Tolerances |
| 394 | FL-6440 Reinforcing Steel Placing Tolerances FL-6450 Filter Media Tolerances ARTICLE FL-7000 PACKAGING, SHIPPING, RECEIVING, STORAGE, AND HANDLING FL-7100 GENERAL REQUIREMENTS FL-7200 FILTER MEDIA ARTICLE FL-8000 QUALITY ASSURANCE FL-8100 GENERAL FL-8110 Scope and Applicability FL-8200 IDENTIFICATION AND COMPLETED MATERIAL ARTICLE FL-9000 LABELS AND MARKINGS FL-9100 DEEP BED SAND FILTER MARKINGS FL-9200 PACKAGE MARKING FL-9300 FILTER MEDIA |
| 395 | MANDATORY APPENDIX FL-I AIR-AEROSOL MIXING TEST PROCEDURES ARTICLE FL-I-1000 INTRODUCTION FL-I-1100 SYSTEM TEST FL-I-1200 SUMMARY OF METHOD FL-I-1300 INJECTION PORT SELECTION CRITERIA FL-I-1400 DOWNSTREAM SAMPLE PORT SELECTION CRITERIA ARTICLE FL-I-2000 PREREQUISITES ARTICLE FL-I-3000 TEST EQUIPMENT ARTICLE FL-I-4000 PROCEDURES FL-I-4100 GENERAL |
| 396 | FL-I-4200 DOWNSTREAM SAMPLE PORT QUALIFICATION |
| 397 | MANDATORY APPENDIX FL-II DEEP BED SAND FILTER IN-PLACE LEAK TEST PROCEDURES ARTICLE FL-II-1000 INTRODUCTION FL-II-1100 SUMMARY OF METHOD ARTICLE FL-II-2000 PREREQUISITES ARTICLE FL-II-3000 TEST EQUIPMENT AND PROCEDURES FL-II-3100 TEST EQUIPMENT FL-II-3200 PROCEDURES |
| 398 | NONMANDATORY APPENDIX FL-A DIVISION OF RESPONSIBILITY Table FL-A-1000-1 Division of Responsibility |
| 399 | NONMANDATORY APPENDIX FL-B GUIDELINES FOR DEEP BED SAND FILTERS ARTICLE FL-B-1000 DBS FILTER MATERIAL SELECTION FL-B-1100 GENERAL FL-B-1200 FILTER MEDIA FL-B-1210 Purity FL-B-1220 Aggregate Types FL-B-1300 DBS FILTER STRUCTURE AND DISTRIBUTION CHANNELS |
| 400 | ARTICLE FL-B-2000 DESIGN GUIDELINES FL-B-2100 GENERAL FL-B-2200 DESIGN ATTRIBUTES FL-B-2210 Provision for Inspections and Maintenance FL-B-2220 Allowance of Bypass Channel FL-B-2300 EXAMPLES OF SUPPORT STRUCTURE ARRANGEMENT FL-B-2400 END OF LIFE ARTICLE FL-B-3000 INSPECTION AND TESTING GUIDELINES FL-B-3100 FILTER MEDIA ACCEPTANCE TEST PROCEDURES |
| 401 | Figure FL-B-2300-1 Sand-Filter Cross Sections |
| 403 | FL-B-3200 SEISMIC FL-B-3300 SMOKE LOADING ARTICLE FL-B-4000 FABRICATION GUIDELINES FL-B-4100 GENERAL FL-B-4200 FILTER MEDIA PLACEMENT |
| 405 | SECTION FM HIGH-STRENGTH HEPA FILTERS ARTICLE FM-1000 INTRODUCTION FM-1100 SCOPE FM-1200 PURPOSE FM-1300 APPLICABILITY FM-1310 High-Strength HEPA Filters FM-1320 High-Strength HEPA Filter Levels of Performance FM-1330 Limitations FM-1340 Division of Responsibility FM-1350 Filter Reliability and Service Life |
| 406 | FM-1400 DEFINITIONS AND TERMS |
| 407 | ARTICLE FM-2000 REFERENCED DOCUMENTS ARTICLE FM-3000 MATERIALS FM-3100 ALLOWABLE MATERIALS FM-3110 Case Materials |
| 408 | FM-3120 Gasket Materials FM-3130 Filter Media FM-3140 Faceguards FM-3150 Adhesives FM-3160 Separators FM-3170 Ancillary Accessories FM-3200 GENERAL MATERIAL REQUIREMENTS FM-3210 Special Limitations of Materials FM-3220 Alternate Materials ARTICLE FM-4000 DESIGN FM-4100 GENERAL DESIGN |
| 409 | FM-4110 High-Strength HEPA Filters FM-4120 Filter Cases FM-4130 High-Strength Filter Packs FM-4140 Gaskets FM-4150 Separators |
| 410 | Figure FM-4110-1 Type A Metal Case Separator Filter Table FM-4110-1 Nominal Sizes and Ratings |
| 411 | FM-4160 Faceguards FM-4200 PERFORMANCE REQUIREMENTS FM-4210 Test Aerosol Particle Penetration FM-4220 Resistance to Flow FM-4300 SEISMIC QUALIFICATION ARTICLE FM-5000 INSPECTION AND TESTING Figure FM-4142-1 Gel Seal Filter Corner — Isometric |
| 412 | FM-5100 INITIAL FILTER INSPECTION Table FM-4200-1 Filter Performance Requirements During Service Operations |
| 413 | FM-5200 QUALIFICATION TESTING FM-5210 Resistance to Flow FM-5220 Test Aerosol Particle Penetration |
| 414 | Table FM-5200-1 Qualification Test Groups and Sequence |
| 415 | Figure FM-5200-1 Process Flow Chart for Filter Qualification (Excluding Optional Seismic Qualification) |
| 416 | FM-5230 Resistance to Rough Handling FM-5240 Resistance to Pressure and Resistance to Pressure Impulse Table FM-5220-1 Acceptable Aerosol Particle Penetration Test Apparatus/Technique |
| 417 | Table FM-5243-1 Test Conditions and Requirements for Resistance to Pressure Impulse |
| 418 | FM-5250 Resistance to Heated Air FM-5260 Resistance to Spot Flame FM-5270 Requirements for Optional Seismic Qualification Test FM-5280 Inspection Requirements for Residual Physical Integrity |
| 419 | FM-5300 PRODUCTION TESTING ARTICLE FM-6000 FABRICATION FM-6100 GENERAL REQUIREMENTS FM-6200 MANUFACTURE AND ASSEMBLY FM-6210 Tolerances FM-6220 Installation of High-Strength Filter Medium FM-6300 WORKMANSHIP ARTICLE FM-7000 PACKAGING, SHIPPING, AND STORAGE ARTICLE FM-8000 QUALITY ASSURANCE FM-8100 RESPONSIBILITY FM-8200 CERTIFICATE OF CONFORMANCE |
| 420 | ARTICLE FM-9000 LABELS AND MARKINGS FM-9100 FILTER MARKING FM-9200 PACKAGE MARKING |
| 421 | MANDATORY APPENDIX FM-I HIGH-STRENGTH FILTER MEDIA — FIRE-RESISTANT, HIGH EFFICIENCY ARTICLE FM-I-1000 SCOPE ARTICLE FM-I-2000 REFERENCED DOCUMENTS ARTICLE FM-I-3000 PERFORMANCE REQUIREMENTS FM-I-3100 FORM AND SIZE FM-I-3110 Form FM-I-3120 Size FM-I-3130 Splices FM-I-3200 PHYSICAL AND CHEMICAL FM-I-3210 Flow Resistance |
| 422 | FM-I-3220 Test Aerosol Particle Penetration FM-I-3230 Tensile Strength FM-I-3240 Water Repellency FM-I-3250 Thickness FM-I-3260 Combustible Material FM-I-3270 Flexing Characteristics FM-I-3271 Examination After Flexing. FM-I-3272 Test Aerosol Particle Penetration After Flexing. |
| 423 | FM-I-3280 Mildew Resistance FM-I-3300 WORKMANSHIP ARTICLE FM-I-4000 INSPECTION AND TESTING FM-I-4100 QUALIFICATION TESTING FM-I-4110 Sample FM-I-4200 TEST PROCEDURES FM-I-4210 Flow Resistance and Test Aerosol Particle Penetration FM-I-4220 Tensile Strength |
| 424 | FM-I-4230 WATER REPELLENCY FM-I-4240 Thickness FM-I-4250 Combustible Material FM-I-4260 Flexing Characteristics FM-I-4270 Mildew Resistance FM-I-4280 Workmanship FM-I-4300 PRODUCTION TESTING FM-I-4310 Production Lot FM-I-4320 Sampling FM-I-4330 Testing ARTICLE FM-I-5000 QUALITY ASSURANCE PROVISIONS FM-I-5100 RESPONSIBILITY FOR INSPECTION FM-I-5110 Supplier’s Responsibility FM-I-5120 Objective Evidence |
| 425 | ARTICLE FM-I-6000 PACKAGING, STORAGE, AND SHIPPING FM-I-6100 PACKAGING AND STORAGE FM-I-6200 SHIPPING FM-I-4330-1 Filter Medium Qualification and Production Tests |
| 426 | NONMANDATORY APPENDIX FM-A DIVISION OF RESPONSIBILITY Table FM-A-1000-1 Division of Responsibility |
| 427 | SECTION FN FILTER MEDIA: HIGH EFFICIENCY ARTICLE FN-1000 INTRODUCTION FN-1100 SCOPE FN-1110 PURPOSE FN-1120 Applicability FN-1130 Definitions and Terms ARTICLE FN-2000 REFERENCE DOCUMENTS ARTICLE FN-3000 MATERIALS FN-3100 ALLOWABLE MATERIALS FN-3110 Fiber FN-3120 Binder |
| 428 | FN-3130 Water Repellent FN-3140 Additional Fibers FN-3150 Nonpermissable Materials ARTICLE FN-4000 DESIGN FN-4100 GENERAL DESIGN REQUIREMENTS FN-4110 Form FN-4120 Size FN-4130 Splices FN-4200 PHYSICAL AND CHEMICAL FN-4210 Airflow Resistance FN-4220 Test Aerosol Penetration FN-4230 Tensile Strength |
| 429 | FN-4240 Water Repellency FN-4250 Thickness FN-4260 Combustible Material FN-4270 Flexing Characteristics FN-4280 Mildew Resistance FN-4300 WORKMANSHIP ARTICLE FN-5000 INSPECTION AND TESTING FN-5100 QUALIFICATION TESTING FN-5110 Sample FN-5200 TEST PROCEDURES FN-5210 Airflow Resistance and Test Aerosol Penetration FN-5220 Tensile Strength |
| 430 | FN-5230 Water Repellency FN-5240 Thickness FN-5250 Combustible Material FN-5260 Flexing Characteristics FN-5270 Mildew Resistance FN-5280 Workmanship FN-5300 PRODUCTION TESTING FN-5310 Production Lot FN-5320 Sampling |
| 431 | FN-5330 Testing ARTICLE FN-6000 FABRICATION FN-6100 GENERAL REQUIREMENTS FN-6200 MANUFACTURE AND ASSEMBLY FN-6210 Tolerances FN-6300 WORKMANSHIP ARTICLE FN-7000 PACKAGING, SHIPPING, AND STORAGE FN-7100 PACKAGING FN-7200 SHIPPING FN-7300 STORAGE ARTICLE FN-8000 QUALITY ASSURANCE FN-8100 RESPONSIBILITY FOR INSPECTION FN-8110 Supplier’s Responsibility Table FN-5330-1 Filter Media Qualification and Production Tests |
| 432 | FN-8120 Objective Evidence ARTICLE FN-9000 NAMEPLATES FN-9100 MEDIA ROLL MARKING FN-9200 PACKAGE MARKING |
| 433 | NONMANDATORY APPENDIX FN-A DIVISION OF RESPONSIBILITY Table FN-A-1000-1 Division of Responsibility |
| 434 | SECTION IA INSTRUMENTATION AND CONTROLS ARTICLE IA-1000 INTRODUCTION IA-1100 SCOPE IA-1200 PURPOSE IA-1300 APPLICABILITY IA-1400 DEFINITIONS AND TERMS |
| 435 | ARTICLE IA-2000 REFERENCED DOCUMENTS ARTICLE IA-3000 MATERIALS IA-3100 MATERIALS OF CONSTRUCTION |
| 436 | IA-3200 NONPERMISSIBLE MATERIALS IA-3300 RESTRICTED MATERIALS IA-3400 CERTIFICATION OF MATERIAL ARTICLE IA-4000 DESIGN REQUIREMENTS IA-4100 GENERAL DESIGN IA-4110 Purpose IA-4120 Design Specification Table IA-3100-1 Allowable Materials |
| 437 | IA-4130 Manufacturer’s Documentation Requirements IA-4140 Clarification of Code Applicability IA-4200 SINGLE-FAILURE CRITERIA IA-4210 Common Cause Failure IA-4300 SEPARATION CRITERIA IA-4310 Circuits and Devices IA-4320 Instrument-Sensing Lines IA-4400 QUALIFICATION OF EQUIPMENT IA-4410 Normal Operating Conditions |
| 438 | IA-4420 Environmental Qualification IA-4430 Seismic Qualification IA-4440 Qualification Documentation IA-4500 PANELS IA-4510 General IA-4520 Structures and Enclosure Materials IA-4530 Panel Wiring |
| 439 | IA-4540 Power Supply and Fuses IA-4550 Panel Piping, Tubing, Valves, and Fittings IA-4560 Instrument Air-Supply Header Assembly IA-4570 Instrument Tags IA-4600 MOUNTED INSTRUMENTS AND SENSORS IA-4700 INTERCONNECTING WIRING FOR SKID-MOUNTED COMPONENTS IA-4800 INSTRUMENT-SENSING LINES AND FIELD-INSTALLED TUBING IA-4810 Pressure Boundary and Mechanical Design Requirements |
| 440 | IA-4820 Tube Pitch and Condensate Trap IA-4830 Support System IA-4840 Root Valves and Isolation Valves IA-4900 INSTRUMENT SET POINTS ARTICLE IA-5000 INSPECTION AND TESTING IA-5100 GENERAL IA-5110 Procedures for Inspection and Testing IA-5120 Test Reports IA-5200 VISUAL INSPECTION IA-5220 Methods of Visual Examination IA-5230 Written Procedures |
| 441 | IA-5300 CALIBRATION AND TESTING IA-5310 Panel-Mounted Instruments IA-5320 Local Mounted Instruments IA-5330 Pressure Testing of Tubing and Sensing Lines ARTICLE IA-6000 PANEL FABRICATION AND ASSEMBLY IA-6100 GENERAL REQUIREMENTS IA-6110 Materials IA-6200 FABRICATION PROCESS IA-6211 IA-6212 Panel Fabrication by Welding IA-6220 Fittings and Aligning IA-6230 Mechanical Joints IA-6300 WELDING IA-6400 BRAZING IA-6500 CLEANING AND COATING IA-6600 INSTALLATION REQUIREMENTS: HANDLING AND RIGGING |
| 442 | IA-6700 MATERIAL IDENTIFICATION ARTICLE IA-7000 PACKAGING, SHIPPING, RECEIVING, STORAGE, AND HANDLING IA-7100 GENERAL REQUIREMENTS IA-7200 PACKAGING IA-7300 SHIPPING IA-7400 RECEIVING IA-7410 Inspection IA-7420 Disposition IA-7500 STORAGE ARTICLE IA-8000 QUALITY ASSURANCE IA-8100 GENERAL IA-8200 TEST REPORTS AND DATA IA-8210 IA-8220 ARTICLE IA-9000 NAMEPLATES IA-9100 GENERAL |
| 443 | IA-9200 REQUIREMENTS IA-9300 NAMEPLATE SPECIFICATIONS IA-9310 Material IA-9320 Size IA-9330 Information |
| 444 | NONMANDATORY APPENDIX IA-A DIVISION OF RESPONSIBILITY Table IA-A-1000-1 Division of Responsibility |
| 445 | NONMANDATORY APPENDIX IA-B SAMPLE CHECKLIST FOR VISUAL EXAMINATION OF CONTROL PANELS/ENCLOSURES, INSTRUMENTS, AND CONTROL DEVICES Table IA-B-1000-1 Sample Checklist for Visual Examination of Control Panels/Enclosures, Instruments, and Control Devices |
| 446 | NONMANDATORY APPENDIX IA-C INSTRUMENTATION FOR NUCLEAR AIR AND GAS TREATMENT SYSTEMS ARTICLE IA-C-1000 INSTRUMENTATION IA-C-1100 PURPOSE IA-C-1200 FUNCTIONAL DESIGN IA-C-1210 General IA-C-1220 Recommended System Parameters Table IA-C-1220-1 Instrumentation for Nuclear Air and Gas Treatment Systems |
| 447 | Division III Process Gas Treatment SECTION GA HEAT EXCHANGERS ARTICLE GA-1000 INTRODUCTION GA-1100 SCOPE GA-1200 PURPOSE GA-1300 APPLICABILITY GA-1310 Clarification of Code Applicability GA-1320 Exclusion of Components GA-1330 Interfacing Boundaries GA-1400 DEFINITIONS AND TERMS |
| 448 | ARTICLE GA-2000 REFERENCED DOCUMENTS |
| 449 | ARTICLE GA-3000 MATERIALS GA-3100 GENERAL REQUIREMENTS GA-3110 Material Specifications GA-3200 MATERIALS FOR HEAT EXCHANGERS GA-3210 Materials for Pressure-Retaining Heat Exchanger Components GA-3220 Materials for Nonmetallic Heat Exchanger Components GA-3300 CERTIFICATION OF MATERIALS GA-3310 General Requirements ARTICLE GA-4000 DESIGN GA-4100 DESIGN SPECIFICATIONS |
| 450 | GA-4200 STRUCTURAL REQUIREMENTS FOR HEAT EXCHANGERS GA-4210 General GA-4220 Load Definition GA-4230 Structural Verification GA-4300 DESIGN CONDITIONS FOR SHELL-AND-TUBE HEAT EXCHANGERS GA-4310 Design Specification GA-4320 Technical Requirements |
| 451 | Figure GA-4311-1 Typical Shell-and-Tube Heat Exchanger |
| 452 | GA-4400 DESIGN CONDITIONS FOR GASKETED PLATE AND FRAME HEAT EXCHANGERS GA-4410 Design Specification |
| 453 | GA-4420 Technical Requirements Figure GA-4411-1 Gasketed Plate and Frame Heat Exchanger |
| 454 | GA-4430 Structural Requirements GA-4500 DESIGN CONDITIONS FOR BRAZED-PLATE HEAT EXCHANGERS GA-4510 Design Specification GA-4520 Technical Requirements Figure GA-4510-1 Brazed-Plate Heat Exchanger |
| 455 | GA-4530 Structural Requirements GA-4600 DESIGN CONDITIONS FOR WELDED-PLATE HEAT EXCHANGERS GA-4610 Design Specification GA-4620 Technical Requirements |
| 456 | Figure GA-4611-1 Typical Welded-Plate Heat Exchanger |
| 457 | GA-4630 Structural Requirements ARTICLE GA-5000 INSPECTION AND TESTING GA-5100 GENERAL REQUIREMENTS GA-5200 TESTING GA-5210 Performance Verification GA-5220 Leak Testing for Heat Exchangers GA-5300 NONDESTRUCTIVE EXAMINATION GA-5310 Material Examination |
| 458 | GA-5320 Visual Examination of Brazed Joints ARTICLE GA-6000 FABRICATION AND INSTALLATION GA-6100 GENERAL REQUIREMENTS GA-6200 WELDING GA-6300 BRAZING GA-6400 MECHANICAL JOINING GA-6500 CLEANING, FINISHING, AND COATING GA-6510 General GA-6520 Finishing and Surface Preparation |
| 459 | GA-6530 Coating and Application GA-6600 INSTALLATION ARTICLE GA-7000 PACKAGING, SHIPPING, HANDLING, AND STORAGE GA-7100 GENERAL REQUIREMENTS GA-7200 PACKAGING GA-7210 ASME BPVC, Section III Heat Exchangers GA-7220 ASME BPVC, Section VIII Heat Exchangers |
| 460 | GA-7300 SHIPPING GA-7310 ASME BPVC, Section III Heat Exchangers GA-7320 ASME BPVC, Section VIII Heat Exchangers GA-7400 STORAGE GA-7410 ASME BPVC, Section III Heat Exchangers GA-7420 ASME BPVC, Section VIII Heat Exchangers |
| 461 | GA-7500 HANDLING GA-7510 General Requirements GA-7520 ASME BPVC, Section III Heat Exchangers GA-7530 ASME BPVC, Section VIII Heat Exchangers ARTICLE GA-8000 QUALITY ASSURANCE GA-8100 GENERAL REQUIREMENTS GA-8200 DOCUMENTATION AND RETENTION |
| 462 | ARTICLE GA-9000 NAMEPLATES AND RECORDS GA-9100 GENERAL REQUIREMENTS GA-9200 HEAT EXCHANGERS GA-9300 INFORMATION ON HEAT EXCHANGER NAMEPLATES GA-9400 NAMEPLATE VISIBILITY GA-9500 DATA REPORTS ARTICLE GA-10000 REPAIRS AND REPLACEMENTS GA-10100 GENERAL |
| 463 | NONMANDATORY APPENDIX GA-A DIVISION OF RESPONSIBILITY Table GA-A-1000-1 Division of Responsibility |
| 464 | NONMANDATORY APPENDIX GA-B DESIGN RECOMMENDATIONS FOR GASKETED PLATE AND FRAME HEAT EXCHANGERS ARTICLE GA-B-1000 DESIGN RECOMMENDATIONS |
| 465 | SECTION GB NOBLE GAS HOLD-UP EQUIPMENT |
| 466 | SECTION GC GAS COMPRESSORS AND EXHAUSTERS ARTICLE GC-1000 INTRODUCTION GC-1100 SCOPE GC-1200 PURPOSE GC-1300 APPLICABILITY GC-1400 DEFINITIONS AND TERMS |
| 467 | ARTICLE GC-2000 REFERENCED DOCUMENTS ARTICLE GC-3000 MATERIALS GC-3100 GENERAL GC-3110 Material Stress Values GC-3200 SPECIAL LIMITATIONS ON MATERIALS GC-3300 CERTIFICATION OF MATERIALS GC-3310 Centrifugal and Axial Compressors GC-3320 Rotary Screw and Reciprocating Compressors GC-3400 PURCHASED MATERIALS |
| 468 | GC-3500 DRIVER MATERIALS ARTICLE GC-4000 DESIGN GC-4100 DESIGN CONDITIONS GC-4110 Performance GC-4120 Environmental Conditions GC-4130 Loading and Conditions GC-4140 Leakage |
| 469 | GC-4150 Equipment and Support Boundary GC-4160 Vibration GC-4200 SPECIFICATION DESIGN REQUIREMENTS GC-4210 Compressors |
| 470 | GC-4220 Drivers GC-4300 CONSTRUCTION GC-4310 General GC-4320 Centrifugal and Axial Compressors GC-4330 Reciprocating Compressors GC-4340 Rotary Screw Compressors GC-4350 Drivers and Drives GC-4360 Accessories |
| 471 | GC-4400 REPORTS AND CALCULATIONS GC-4410 Performance Rating GC-4420 Equipment Sound Production GC-4430 Structural Verification Considerations |
| 472 | ARTICLE GC-5000 INSPECTION AND TESTING GC-5100 COMPRESSOR INSPECTION AND TESTING GC-5110 General Testing Requirements GC-5120 Performance Acceptance Tests GC-5130 Sound Tests GC-5140 Mechanical Tests |
| 473 | GC-5150 Test Results and Reports GC-5200 DRIVER INSPECTION AND TESTING GC-5210 First Unit of a Design GC-5220 Succeeding Units of a Design ARTICLE GC-6000 FABRICATION AND INSTALLATION GC-6100 GENERAL GC-6200 FABRICATION GC-6210 Selection of Materials GC-6300 INSTALLATION ARTICLE GC-7000 PACKAGING, SHIPPING, RECEIVING, AND STORAGE GC-7100 GENERAL GC-7200 PACKAGING GC-7300 SHIPPING GC-7400 RECEIVING |
| 474 | GC-7500 STORAGE ARTICLE GC-8000 QUALITY ASSURANCE GC-8100 GENERAL GC-8200 REQUIRED DOCUMENTATION GC-8210 Certified Performance Curves GC-8220 Material Certification GC-8300 DRAWINGS AND DOCUMENTATION ARTICLE GC-9000 NAMEPLATES AND INSTALLATION, OPERATION, AND MAINTENANCE MANUALS GC-9100 GENERAL GC-9200 REQUIRED NAMEPLATE DATA GC-9210 Compressor Nameplate Data GC-9220 Driver Nameplate Data GC-9300 ACCESSORIES GC-9310 Acceptable Marking Methods GC-9400 INSTALLATION, OPERATION, AND MAINTENANCE MANUALS |
| 475 | MANDATORY APPENDIX GC-I SHAFT LEAKAGE Table GC-I-1000-1 Maximum Permissible Shaft Leakage Rate, scfm, at Pressure Differential Between Operating and Ambient |
| 476 | MANDATORY APPENDIX GC-II SYSTEM CONSIDERATIONS GC-II-1100 SYSTEM CHARACTERISTICS GC-II-1200 SYSTEM EFFECTS ON PERFORMANCE GC-II-1300 EQUIPMENT AND SYSTEM MATCHING GC-II-1400 SYSTEM CAPACITY CONTROL GC-II-1500 MULTIPLE-UNIT SYSTEMS |
| 477 | NONMANDATORY APPENDIX GC-A DIVISION OF RESPONSIBILITY |
| 478 | Table GC-A-1000-1 Division of Responsibility |
| 480 | SECTION GE HYDROGEN RECOMBINERS AND IGNITERS ARTICLE GE-1000 INTRODUCTION GE-1100 SCOPE GE-1200 PURPOSE GE-1300 APPLICABILITY GE-1310 Limitations GE-1320 Responsibility GE-1400 DEFINITIONS AND TERMS |
| 482 | ARTICLE GE-2000 REFERENCED DOCUMENTS ARTICLE GE-3000 MATERIALS GE-3100 GENERAL REQUIREMENTS GE-3110 Materials GE-3120 Welding and Brazing Material GE-3200 PAR GE-3300 IGNITER ARTICLE GE-4000 DESIGN GE-4100 GENERAL DESIGN |
| 483 | GE-4110 Design Specification GE-4200 PAR GE-4300 IGNITER GE-4400 STRUCTURAL REQUIREMENTS GE-4410 Load Criteria |
| 484 | GE-4420 Stress Criteria GE-4430 Deflection Criteria ARTICLE GE-5000 INSPECTION AND TESTING GE-5100 GENERAL GE-5200 PERFORMANCE TESTING GE-5210 PAR Performance Testing Table GE-4410-1 Load Conditions — Housing and Support |
| 485 | GE-5220 Igniter Performance Testing ARTICLE GE-6000 FABRICATION AND INSTALLATION GE-6100 GENERAL REQUIREMENTS GE-6200 FABRICATION PROCESSES GE-6300 WELDING GE-6400 BRAZING GE-6500 CLEANING AND COATING GE-6510 General GE-6520 Housing Cleaning and Finishing, Coating, and Application GE-6600 INSTALLATION REQUIREMENTS |
| 486 | ARTICLE GE-7000 PACKAGING, SHIPPING, RECEIVING, STORAGE, AND HANDLING GE-7100 GENERAL REQUIREMENTS GE-7200 PACKAGING GE-7300 SHIPPING GE-7400 STORAGE GE-7500 RECEIVING GE-7600 HANDLING AND RIGGING GE-7700 ASSEMBLY, ERECTION, AND START-UP ARTICLE GE-8000 QUALITY ASSURANCE GE-8100 GENERAL REQUIREMENTS GE-8200 IDENTIFICATION AND CONTROL OF ITEMS GE-8300 DOCUMENTATION ARTICLE GE-9000 NAMEPLATES AND CERTIFICATION GE-9100 GENERAL REQUIREMENTS GE-9200 INFORMATION ON NAMEPLATES |
| 487 | GE-9300 PAR NAMEPLATE LOCATION GE-9400 DATA REPORTS ARTICLE GE-10000 REPAIR AND REPLACEMENT OF COMPONENTS GE-10100 GENERAL REQUIREMENTS |
| 488 | NONMANDATORY APPENDIX GE-A DIVISION OF RESPONSIBILITY Table GE-A-1000-1 Division of Responsibility |
| 489 | NONMANDATORY APPENDIX GE-B ILLUSTRATIONS OF COMPONENTS Figure GE-B-1000-1 Typical PAR |
| 490 | Figure GE-B-1000-2 Typical Igniter |
| 491 | NONMANDATORY APPENDIX GE-C PERIODIC TESTING GUIDELINES GE-C-1100 IN-SERVICE TEST REQUIREMENTS GE-C-1110 PAR Testing GE-C-1120 Igniter Testing GE-C-1200 STRUCTURAL INSPECTION |
| 492 | SECTION GF GAS SAMPLING |
| 493 | SECTION GG SCRUBBERS |
| 494 | SECTION GH CYCLONES |
| 495 | SECTION GJ FILTERS |
| 496 | SECTION GK MIST ELIMINATORS |
| 497 | SECTION GM NOBLE GAS HOLD-UP MEDIA ARTICLE GM-1000 INTRODUCTION GM-1100 SCOPE GM-1200 APPLICABILITY GM-1300 DEFINITIONS AND TERMS ARTICLE GM-2000 REFERENCED DOCUMENTS ARTICLE GM-3000 MATERIALS GM-3100 ACTIVATED CARBON |
| 498 | ARTICLE GM-4000 DESIGN GM-4100 ACTIVATED CARBON ARTICLE GM-5000 INSPECTION AND TESTING GM-5100 INTRODUCTION GM-5200 ACTIVATED CARBON FOR NOBLE GAS DELAY GM-5210 Physical Testing GM-5220 Performance Testing ARTICLE GM-6000 FABRICATION GM-6100 FABRICATION GUIDELINES ARTICLE GM-7000 PACKAGING, SHIPPING, STORAGE, AND HANDLING GM-7100 GENERAL REQUIREMENTS GM-7200 PROTECTION OF CARBON MEDIA |
| 499 | GM-7300 PACKAGING GM-7310 General GM-7320 Polyethylene Barrier Material GM-7400 STORAGE GM-7500 HANDLING GM-7600 SHIPPING GM-7610 General GM-7620 Post-loading Inspection GM-7630 Sealed Openings GM-7640 Stacking GM-7700 MARKING |
| 500 | ARTICLE GM-8000 QUALITY CONTROL GM-8100 GENERAL REQUIREMENTS GM-8200 DOCUMENTATION ARTICLE GM-9000 NAMEPLATES AND CERTIFICATION GM-9100 NAMEPLATE, CERTIFICATION, AND SHIPPING INFORMATION |
| 501 | NONMANDATORY APPENDIX GM-A DIVISION OF RESPONSIBILITY Table GM-A-1000-1 Division of Responsibility |
| 502 | NONMANDATORY APPENDIX GM-B DETERMINATION OF THE DYNAMIC ADSORPTION COEFFICIENT — RADIOACTIVE TRACER METHOD GM-B-1100 SCOPE GM-B-1200 APPLICABLE DOCUMENTS |
| 503 | Figure GM-B-3000-1 Schematic of Noble Gas Delay Test Apparatus |
| 504 | GM-B-7100 SYSTEM DEAD TIME DETERMINATION GM-B-7200 DETERMINATION OF AVERAGE DELAY TIME |
| 506 | Figure GM-B-7100-1 Typical Traces for Measurement of Delay Time, Tdelay, for Dynamic K Determination |
| 507 | Division IV Testing Procedures SECTION TA FIELD TESTING OF AIR TREATMENT SYSTEMS ARTICLE TA-1000 INTRODUCTION TA-1100 SCOPE TA-1200 PURPOSE TA-1300 APPLICABILITY TA-1400 DEFINITIONS AND TERMS |
| 508 | ARTICLE TA-2000 REFERENCED DOCUMENTS ARTICLE TA-3000 GENERAL INSPECTION AND TEST REQUIREMENTS TA-3100 GENERAL TA-3200 TEST INSTRUMENTS TA-3210 Range Requirements TA-3220 Instrument Fluctuation TA-3230 Evaluation Following Test Instrument Loss, Damage, or Calibration Failure TA-3240 Specific Instrument Accuracy Requirements |
| 509 | TA-3300 ESTABLISHMENT OF REFERENCE VALUES TA-3400 INSPECTIONS AND TEST REQUIREMENTS TA-3410 Inspection and Test Parameters TA-3420 System Operating Conditions Table TA-3200-1 Instrument Accuracy Requirements |
| 510 | TA-3430 Procedure Requirements TA-3440 Test Reports TA-3500 GENERIC TESTS TA-3510 Visual Inspections TA-3520 Pressure Boundary Tests TA-3530 Functional Tests |
| 511 | TA-3600 ACCEPTANCE CRITERIA TA-3610 Visual Inspection TA-3620 Pressure Boundary Tests TA-3630 Functional Tests ARTICLE TA-4000 FIELD ACCEPTANCE TESTS TA-4100 FAN ACCEPTANCE TESTS TA-4110 Acceptance Test Requirements TA-4120 Visual Inspection TA-4130 Pressure Boundary Tests Table TA-4110-1 Fan Acceptance Tests |
| 512 | TA-4140 Component Functional Tests TA-4150 System Functional Tests TA-4160 Acceptance Criteria TA-4200 DAMPER ACCEPTANCE TESTS TA-4210 Acceptance Test Requirements |
| 513 | TA-4220 Visual Inspection TA-4230 Pressure Boundary Tests TA-4240 Component Functional Tests TA-4250 System Functional Tests Table TA-4210-1 Damper Acceptance Tests |
| 514 | TA-4300 DUCT, HOUSING, AND MOUNTING FRAME ACCEPTANCE TESTS TA-4310 Acceptance Test Requirements TA-4320 Visual Inspection TA-4330 Pressure Boundary Tests TA-4400 REFRIGERATION EQUIPMENT ACCEPTANCE TESTS TA-4410 Acceptance Test Requirements Table TA-4310-1 Duct, Housing, and Frame Acceptance Tests Table TA-4410-1 Refrigeration Equipment Acceptance Tests |
| 515 | TA-4420 Visual Inspection TA-4430 Pressure Boundary Tests TA-4440 Component Functional Tests TA-4450 System Functional Tests TA-4500 CONDITIONING EQUIPMENT ACCEPTANCE TESTS TA-4510 Acceptance Test Requirements |
| 516 | TA-4520 Visual Inspection TA-4530 Hydrostatic Test for Hydronic Piping and Coils TA-4540 Component Functional Tests TA-4550 System Functional Tests Table TA-4510-1 Conditioning Equipment Acceptance Tests |
| 517 | TA-4560 Hydronic System Heating and Cooling Performance Test TA-4570 Acceptance Criteria TA-4600 MOISTURE SEPARATOR, PREFILTER, AND HEPA FILTER BANK ACCEPTANCE TESTS TA-4610 Acceptance Test Requirements TA-4620 Visual Inspection TA-4630 System Functional Tests Table TA-4610-1 Moisture Separator, Prefilter, and HEPA Filter Acceptance Tests |
| 518 | TA-4640 Acceptance Criteria TA-4700 TYPES II, III, AND IV ADSORBER BANK ACCEPTANCE TESTS TA-4710 Acceptance Test Requirements TA-4720 Visual Inspection TA-4730 Component Functional Tests TA-4740 System Functional Tests Table TA-4710-1 Types II, III, and IV Adsorber Bank Acceptance Tests |
| 519 | TA-4750 Acceptance Criteria TA-4800 ADSORBENT ACCEPTANCE TESTS TA-4810 Acceptance Test Requirements TA-4820 Laboratory Analysis of Adsorbent TA-4900 INTEGRATED SYSTEM TESTS TA-4910 Fan-Integrated System Test Requirements |
| 520 | TA-4920 Damper-Integrated System Test Requirements TA-4930 Refrigeration and Conditioning Integrated System Test Requirements TA-4940 HEPA and Adsorber Bank Integrated System Test Requirements TA-4950 Integrated System Habitability Envelope Test Requirements ARTICLE TA-5000 CORRECTIVE ACTION REQUIREMENTS ARTICLE TA-6000 QUALITY ASSURANCE TA-6100 GENERAL TA-6200 PERSONNEL TA-6300 DOCUMENTATION TA-6310 Procedures TA-6320 Reports |
| 521 | MANDATORY APPENDIX TA-I VISUAL INSPECTION CHECKLIST TA-I-1100 FAN INSPECTION ITEMS TA-I-1200 DAMPER INSPECTION ITEMS TA-I-1300 DUCT, HOUSING, AND MOUNTING FRAME INSPECTION ITEMS TA-I-1400 REFRIGERATION EQUIPMENT INSPECTION ITEMS |
| 522 | TA-I-1500 CONDITIONING EQUIPMENT INSPECTION ITEMS TA-I-1600 MOISTURE SEPARATOR BANK, PREFILTER BANK, AND HEPA FILTER BANK INSPECTION ITEMS TA-I-1700 TYPES II, III, AND IV ADSORBER BANK INSPECTION ITEMS |
| 523 | MANDATORY APPENDIX TA-II STRUCTURAL CAPABILITY TEST PROCEDURES TA-II-1100 SUMMARY OF METHOD |
| 524 | MANDATORY APPENDIX TA-III DUCT AND HOUSING LEAK TEST PROCEDURES TA-III-1100 SUMMARY OF METHOD TA-III-4100 CONSTANT PRESSURE TEST |
| 525 | TA-III-4200 PRESSURE DECAY TEST TA-III-4300 ACCEPTANCE CRITERIA TA-III-4400 BUBBLE LEAK LOCATION METHOD TA-III-4500 AUDIBLE LEAK LOCATION METHOD |
| 526 | MANDATORY APPENDIX TA-IV AIRFLOW DISTRIBUTION TEST PROCEDURES TA-IV-1100 SUMMARY OF METHOD |
| 527 | MANDATORY APPENDIX TA-V AIR-AEROSOL MIXING TEST PROCEDURES TA-V-1100 SYSTEM TEST TA-V-1200 SUMMARY OF METHOD TA-V-1300 INJECTION PORT SELECTION CRITERIA TA-V-1400 DOWNSTREAM SAMPLE PORT SELECTION CRITERIA TA-V-4100 GENERAL |
| 528 | TA-V-4200 DOWNSTREAM SAMPLE PORT QUALIFICATION |
| 529 | MANDATORY APPENDIX TA-VI HEPA FILTER BANK IN-PLACE LEAK TEST PROCEDURES TA-VI-1100 SUMMARY OF METHOD |
| 530 | MANDATORY APPENDIX TA-VII ADSORBER BANK IN-PLACE LEAK TEST PROCEDURES TA-VII-1100 SUMMARY OF METHOD |
| 531 | MANDATORY APPENDIX TA-VIII REFRIGERANT PIPING AND COIL SYSTEM LEAK TEST PROCEDURES TA-VIII-1100 SUMMARY OF METHOD TA-VIII-4100 LEAK TEST PROCEDURES TA-VIII-4200 EVACUATION AND DEHYDRATION PROCEDURE |
| 532 | TA-VIII-4210 Deep Vacuum Method |
| 533 | NONMANDATORY APPENDIX TA-A MOUNTING FRAME PRESSURE LEAK TEST PROCEDURES TA-A-1100 SUMMARY OF METHOD |
| 534 | NONMANDATORY APPENDIX TA-B CORRECTIVE ACTION GUIDANCE |
| 535 | NONMANDATORY APPENDIX TA-C CHALLENGE GAS AND AEROSOL SUBSTITUTE SELECTION CRITERIA TA-C-1100 ALTERNATIVE CHALLENGE GASES TA-C-1200 ALTERNATIVE CHALLENGE AEROSOLS |
| 536 | SECTION TB FIELD TESTING OF GAS-PROCESSING SYSTEMS |
| 537 | Division V Nonmandatory System Guidance |
Related products
-
NFPA 921 2021
NFPA 921: Guide for Fire and Explosion Investigations Published By Publication Date Number of Pages…
-
IEEE 1901-2020(Redline)
IEEE Standard for Broadband over Power Line Networks: Medium Access Control and Physical Layer Specifications…
-
VA Residential Code 2021 1stptg
Virginia Residential Code Published By Publication Date Number of Pages VA 2021
-
WA StateResidentialCode 2021 1stptg
Washington State Residential Code Based on the 2021 International Residential Code Published By Publication Date…
-
ASME BPVC X 2023
ASME BPVC.X-2023 Section X, Fiber-Reinforced Plastic Pressure Vessels Published By Publication Date Number of Pages…
-
ICC IRC 2021 1stptg
International Residential Code, 3rd Printing Published By Publication Date Number of Pages ICC 2021 1109
-
CSA S16:F19:2019 Edition
Règles de calcul des charpentes en acier (Incorporation de historique des modifications 2020) Published By…
-
ASTM-D8064 2016
D8064-16 Standard Test Method for Elemental Analysis of Soil and Solid Waste by Monochromatic Energy…
-
ICC IRC Commentary Volume 2 2021 1stptg
International Residential Code and Commentary, Volume 2 Published By Publication Date Number of Pages ICC…
-
ASME AG 1 2015
ASME AG-1 – 2015: Code on Nuclear Air and Gas Treatment Published By Publication Date…
-
BS EN 15502-2-3:2023
Gas-fired central heating boilers – Specific standard for hybrid units combining a gas-fired boiler and…
-
CA City of LA Residential Code 2023 1stptg
City of Los Angeles Residential Code – Full Code Published By Publication Date Number of…
-
NJ ResidentialCode 2021 1stptg
International Residential Code, New Jersey Edition Published By Publication Date Number of Pages NJ 2021
-
ASME BPVC X 2019
ASME BPVC – X -2019 BPVC Section X, Fiber-Reinforced Plastic Pressure Vessels Published By Publication…
-
ASHRAE HVACApplications Handbook SI 2015
ASHRAE Handbook – HVAC Applications (SI) Published By Publication Date Number of Pages ASHRAE 2015…
-
ASME AG 1 2019
ASME AG-1-2019 Code on Nuclear Air and Gas Treatment Published By Publication Date Number of…
-
BS EN 15502-2-1:2022+A1:2023:2024 Edition
Gas-fired central heating boilers – Specific standard for type C appliances and type B2, B3…
-
ASHRAE Handbook HVAC Applications 2023 IP
ASHRAE Handbook — HVAC Applications (I-P) Published By Publication Date Number of Pages ASHRAE 2023
-
NFPA 1192, Standard on Recreational Vehicles:2021 Edition
NFPA 1192, Standard on Recreational Vehicles Published By Publication Date Number of Pages NFPA 2021…
-
ASHRAE HVACApplications Handbook IP 2015
ASHRAE Handbook – HVAC Applications (I-P) Published By Publication Date Number of Pages ASHRAE 2015…
-
ASHRAE Handbook HVAC Applications 2023 SI
ASHRAE Handbook — HVAC Applications (SI) Published By Publication Date Number of Pages ASHRAE 2023…
-
CA 2022 California Residential Code Approved Express Terms COMPLETE
California Residential Code Approved Express Terms Published By Publication Date Number of Pages CA 2022
-
BS EN 15502-2-1:2022
Gas-fired central heating boilers – Specific standard for type C appliances and type B2, B3…
-
CA LA County Residential 2023
County of Los Angeles Residential Code – Full Code Published By Publication Date Number of…
-
IEEE 1901-2020
IEEE Standard for Broadband over Power Line Networks: Medium Access Control and Physical Layer Specifications…
-
BSI PD CEN/TR 17603-32-02:2022
Space engineering. Structural materials handbook – Design calculation methods and general design aspects Published By…
-
BS EN 15502-2-2:2024
Gas-fired central heating boilers – Specific standard for type B1 appliances Published By Publication Date…
-
CA 2022 California Residential Code Approved Express Terms COMPLETE
California Residential Code Approved Express Terms Published By Publication Date Number of Pages CA 2022…
-
SC ResidentialCode 2021 1stptg
South Carolina Residential Code Published By Publication Date Number of Pages SC 2021
-
CSA S16:19:2019 Edition
Design of steel structures (Including revision history of 2019) Published By Publication Date Number of…
-
ASME AG 1 2017
ASME AG-1 Code on Nuclear Air and Gas Treatment Published By Publication Date Number of…
-
BS EN 15502-2-1:2022 – TC:2023 Edition
Tracked Changes. Gas-fired central heating boilers – Specific standard for type C appliances and type…
-
CA Residential Code Title 24 Part 2.5 2022 1stptg
California Residential Code, Title 24, Part 2.5 (W/ ERRATA & SUPPLEMENT) Published By Publication Date…
