🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASME B16.51 2018

ASME B16.51 2018

$98.04

ASME B16.51 – 2018 Copper and Copper Alloy Press-Connect Pressure Fittings

Published By Publication Date Number of Pages
ASME 2018 30
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

None

PDF Catalog

PDF Pages PDF Title
4 CONTENTS
6 FOREWORD
7 ASME B16 ROSTER
8 CORRESPONDENCE WITH THE B16 COMMITTEE
10 ASME B16.51-2018 SUMMARY OF CHANGES
11 LIST OF CHANGES IN RECORD NUMBER ORDER
12 Copper and Copper Alloy Press-Connect Pressure Fittings
1 SCOPE
2 GENERAL
2.1 Convention
2.2 Relevant Units
2.3 References
2.4 Quality Systems
3 TERMINOLOGY
3.1 Abbreviations
3.2 Definitions
4 SIZE
5 MARKING
13 6 MATERIAL
6.1 Wrought Copper Alloys
6.2 Cast Copper Alloys
6.3 Elastomers (Seals)
6.4 Seal Lubricant
7 LAYING LENGTHS
8 TUBE STOPS
9 DESIGN
9.1 General
14 9.2 Out-of-Roundness of Fitting End (P or FTG)
9.3 Inside Diameter of Fitting
9.4 Wall Thickness
10 THREADED ENDS
10.1 Countersink or Chamfer
10.2 Threading Tolerances
10.3 Design of Threaded Ends
11 ALIGNMENT
12 GAGING
12.1 Preferred Gaging Method of Press-Joint Ends
12.2 Optional Gaging Method of Press-Connect Pressure Fittings
12.3 Standard Gaging Method of Threaded Ends
13 INSTALLATION INSTRUCTIONS
15 14 DESIGN QUALIFICATION
14.1 General
14.2 Hydrostatic Pressure Test at 20°C (68°F)
14.3 Unrestrained Hydrostatic Pressure Test at 93°C (200°F)
14.4 Static Torque Test
14.5 Bending Test
14.6 Vacuum Test
14.7 Cyclic Pressure Test
16 14.8 Vibration Test
14.9 Thermocycling Test
14.10 Dynamic Torque Test
17 Figures
Figure 3.1-1 Method of Designating Laying Lengths of Fittings and Openings of Reducing Fittings
19 Tables
Table 9.1-1 Dimensions of Press-Connect Ends
21 Figure 8-1 Tube Stops
Figure 11-1 Alignment
Figure 14.2.1-1 Test Setup for Pressure Test
22 Figure 14.4.1-1 Test Setup for Static Torque Test
Table 14.2.2-1 Maximum Slippage
Table 14.4.1-1 Torque
23 Figure 14.5.1-1 Test Setup for Bending Test
Table 14.5.1-1 Concentrated Load
24 Figure 14.8.1-1 Test Setup for Vibration Test
Figure 14.9.1-1 Test Setup for Thermocycling Test
25 Figure 14.10.1-1 Test Setup for Dynamic Torque Test
26 MANDATORY APPENDIX I REFERENCES
27 NONMANDATORY APPENDIX A QUALITY SYSTEM PROGRAM
ASME B16.51 2018
$98.04