ASME BPVC III 1 ND 2007
$22.75
ASME BPVC – III – 1 – ND -2007 BPVC Section III, Rules for Constructions of Nuclear Facility Components, Division 1, Subsection ND, Class 3 Components
| Published By | Publication Date | Number of Pages |
| ASME | 2007 |
None
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | LIST OF BPVC SECTIONS |
| 6 | CONTENTS ARTICLE ND- 1000 FIGURES |
| 7 | ARTICLE ND- 2000 FIGURES ARTICLE ND- 2000 TABLES |
| 8 | ARTICLE ND- 3000 FIGURES |
| 9 | ARTICLE ND- 3000 TABLES |
| 11 | ARTICLE ND- 4000 FIGURES |
| 12 | ARTICLE ND- 4000 TABLES |
| 14 | ARTICLE ND- 7000 FIGURES |
| 16 | FOREWORD |
| 18 | STATEMENTS OF POLICY |
| 20 | PERSONNEL |
| 32 | ORGANIZATION OF SECTION III 1 GENERAL 2 SUBSECTIONS 3 ARTICLES 4 SUBARTICLES 5 SUBSUBARTICLES 6 PARAGRAPHS 7 SUBPARAGRAPHS |
| 33 | 8 SUBSUBPARAGRAPHS 9 REFERENCES |
| 34 | SUMMARY OF CHANGES |
| 35 | LIST OF CHANGES IN BC ORDER |
| 36 | ARTICLE ND- 1000 INTRODUCTION ND- 1100 SCOPE ND- 1130 BOUNDARIES OF JURISDICTION APPLICABLE TO THIS SUBSECTION ND- 1131 Boundary of Components |
| 38 | ND-1132.2-1 ATTACHMENTS IN THE COMPONENT SUPPORT LOAD PATH THAT DO NOT PERFORM A PRESSURE RETAINING FUNCTION |
| 39 | ND-1132.2-2 ATTACHMENTS THAT DO NOT PERFORM A PRESSURE RETAINING FUNCTION AND ARE NOT IN THE COMPONENT SUPPORT LOAD PATH (NONSTRUCTURAL ATTACHMENTS) |
| 40 | ND-1132.2-3 ATTACHMENTS THAT PERFORM A PRESSURE RETAINING FUNCTION |
| 41 | ARTICLE ND- 2000 MATERIAL ND- 2100 GENERAL REQUIREMENTS FOR MATERIAL ND- 2110 SCOPE OF PRINCIPAL TERMS EMPLOYED ND- 2120 PRESSURE RETAINING MATERIAL |
| 43 | ND- 2130 CERTIFICATION OF MATERIAL ND- 2140 WELDING MATERIAL ND- 2150 MATERIAL IDENTIFICATION ND- 2160 DETERIORATION OF MATERIAL IN SERVICE ND- 2170 HEAT TREATMENT TO ENHANCE IMPACT PROPERTIES ND- 2180 PROCEDURES FOR HEAT TREATMENT OF MATERIAL |
| 44 | ND- 2190 NONPRESSURE- RETAINING MATERIAL ND- 2200 MATERIAL TEST COUPONS AND SPECIMENS FOR FERRITIC STEEL MATERIAL ND- 2210 HEAT TREATMENT REQUIREMENTS ND- 2211 Test Coupon Heat Treatment for Ferritic Material2 |
| 45 | ND- 2220 PROCEDURE FOR OBTAINING TEST COUPONS AND SPECIMENS FOR QUENCHED AND TEMPERED MATERIAL ND- 2221 General Requirements |
| 47 | ND- 2300 FRACTURE TOUGHNESS REQUIREMENTS FOR MATERIAL ND- 2310 MATERIAL TO BE IMPACT TESTED ND- 2311 Material for Which Impact Testing Is Required |
| 48 | ND- 2320 IMPACT TEST PROCEDURES ND- 2330 TEST REQUIREMENTS AND ACCEPTANCE STANDARDS ND-2311-1 EXEMPTIONS FROM IMPACT TESTING UNDER ND-2311(a)(8) |
| 49 | ND- 2340 NUMBER OF IMPACT TESTS REQUIRED ND-2331(a)-1 REQUIRED Cv LATERAL EXPANSION VALUES FOR PRESSURE RETAINING MATERIAL (EXCEPT BOLTING) |
| 50 | ND- 2350 RETESTS ND-2331(a)-2 REQUIRED Cv ENERGY VALUES FOR PRESSURE RETAINING MATERIAL (EXCEPT BOLTING) ND-2333-1 REQUIRED Cv VALUES FOR BOLTING MATERIAL |
| 51 | ND- 2360 CALIBRATION OF INSTRUMENTS AND EQUIPMENT ND- 2400 WELDING MATERIAL ND- 2410 GENERAL REQUIREMENTS ND- 2420 REQUIRED TESTS |
| 52 | ND- 2430 WELD METAL TESTS |
| 54 | ND-2432.1-1 SAMPLING OF WELDING MATERIALS FOR CHEMICAL ANALYSIS ND-2432.2-1 WELDING MATERIAL CHEMICAL ANALYSIS |
| 55 | ND- 2440 STORAGE AND HANDLING OF WELDING MATERIAL ND- 2500 EXAMINATION AND REPAIR OF PRESSURE RETAINING MATERIAL ND- 2510 PRESSURE RETAINING MATERIAL ND-2433.1-1 DELTA FERRITE CONTENT |
| 56 | ND- 2530 EXAMINATION AND REPAIR OF PLATE ND- 2540 EXAMINATION AND REPAIR OF FORGINGS AND BARS |
| 58 | ND- 2550 EXAMINATION AND REPAIR OF SEAMLESS AND WELDED (WITHOUT FILLER METAL) TUBULAR PRODUCTS AND FITTINGS ND- 2560 EXAMINATION AND REPAIR OF TUBULAR PRODUCTS AND FITTINGS WELDED WITH FILLER METAL |
| 59 | ND- 2570 EXAMINATION AND REPAIR OF STATICALLY AND CENTRIFUGALLY CAST PRODUCTS |
| 60 | ND-2571-1 REQUIRED EXAMINATIONS |
| 63 | ND-2575.2-1 TYPICAL PRESSURE RETAINING PARTS OF PUMPS AND VALVES |
| 66 | ND- 2580 EXAMINATION OF BOLTS, STUDS, AND NUTS ND- 2600 MATERIAL ORGANIZATIONS’ QUALITY SYSTEM PROGRAMS ND- 2610 DOCUMENTATION AND MAINTENANCE OF QUALITY SYSTEM PROGRAMS ND- 2700 DIMENSIONAL STANDARDS |
| 67 | ARTICLE ND- 3000 DESIGN ND- 3100 GENERAL DESIGN ND- 3110 LOADING CRITERIA |
| 68 | ND- 3120 SPECIAL CONSIDERATIONS ND- 3130 GENERAL DESIGN RULES |
| 70 | ND-3132-1 DIMENSIONAL STANDARDS |
| 74 | ND-3133.4-1 LENGTH LOF SOME TYPICAL CONICAL SECTIONS |
| 75 | ND- 3300 VESSEL DESIGN ND- 3310 GENERAL REQUIREMENTS ND- 3320 DESIGN CONSIDERATIONS |
| 76 | ND-3133.7-1 CHART FOR DETERMINING WALL THICKNESS OF TUBES UNDER EXTERNAL PRESSURE |
| 77 | ND-3321-1 STRESS LIMITS FOR DESIGN AND SERVICE LOADINGS |
| 78 | ND-3321-2 CLASSIFICATION OF STRESS IN VESSELS FOR SOME TYPICAL CASES |
| 80 | ND-3324.2-1 PRINCIPAL DIMENSIONS OF TYPICAL HEADS ND-3324.2-1 VALUES OF FACTOR K |
| 83 | ND-3324.8(b)-1 VALUES OF FACTOR M |
| 84 | ND-3324.11(a)(6)-1 LARGE HEAD OPENINGS, REVERSE CURVE, AND CONICAL SHELL REDUCER SECTIONS ND-3324.11(b)(2)-1 VALUES OF DELTA FOR JUNCTIONS AT THE LARGE CYLINDER FOR ALPHA LESS THAN OR EQUAL TO 30 deg ND-3324.11(b)(3)-1 VALUES OF DELTA FOR JUNCTIONS AT THE SMALL CYLINDER FOR ALPHA LESS THAN OR EQUAL TO 30 deg |
| 86 | ND-3325-1 SOME ACCEPTABLE TYPES OF UNSTAYED FLAT HEADS AND COVERS |
| 90 | ND-3326.1-1 SPHERICALLY DISHED COVERS WITH BOLTING FLANGES |
| 92 | ND-3329.1(e)-1 ACCEPTABLE PROPORTIONS FOR ENDS OR THROUGH STAYS |
| 93 | ND-3329.6(b)-1 EXAMPLE OF TUBE SPACING WITH PITCH OF HOLES EQUAL IN EVERY ROW ND-3329.6(b)-2 EXAMPLE OF TUBE SPACING WITH PITCH OF HOLES UNEQUAL IN EVERY SECOND ROW ND-3329.6(b)-3 EXAMPLE OF TUBE SPACING WITH PITCH OF HOLES VARYING |
| 94 | ND- 3330 OPENINGS AND REINFORCEMENT ND-3329.6(d)-1 EXAMPLE OF TUBE SPACING WITH TUBE HOLES ON DIAGONAL LINES |
| 95 | ND-3329.6(d)-2 DIAGRAM FOR DETERMINING THE EFFICIENCY OF LONGITUDINAL AND DIAGONAL LIGAMENTS BETWEEN OPENINGS IN CYLINDRICAL SHELLS |
| 96 | ND-3329.6(g)-1 DIAGRAM FOR DETERMINING EQUIVALENT LONGITUDINAL EFFICIENCY OF DIAGONAL LIGAMENTS |
| 97 | ND-3332.2-1 CHART FOR DETERMINING VALUE OF F |
| 98 | ND-3332.2-1 VALUES OF SPHERICAL RADIUS FACTOR K1 |
| 100 | ND-3335.1(b)-1 SOME REPRESENTATIVE CONFIGURATIONS DESCRIBING THE te REINFORCEMENT DIMENSION |
| 101 | ND-3335.2-1 ARRANGEMENT OF MULTIPLE OPENINGS ND-3335.3(b)-1 MINIMUM DEPTH FOR FLANGE OF FLUED OPENINGS |
| 102 | ND- 3350 DESIGN OF WELDED CONSTRUCTION ND-3351-1 WELDED JOINT LOCATIONS TYPICAL OF CATEGORIES A, B, C, AND D |
| 103 | ND-3352-1 TYPICAL BUTT JOINTS |
| 107 | ND-3358.1(a)-1 HEADS ATTACHED TO SHELLS |
| 109 | ND- 3360 SPECIAL VESSEL REQUIREMENTS. |
| 110 | ND-3361.1-1 BUTT WELDING OF PLATES OF UNEQUAL THICKNESSES ND-3361.3(a)-1 MINIMUM NUMBER OF PIPE THREADS FOR CONNECTIONS |
| 112 | ND- 3400 PUMP DESIGN ND- 3410 GENERAL REQUIREMENTS FOR CENTRIFUGAL PUMPS |
| 113 | ND- 3420 DEFINITIONS ND-3423-1 TYPICAL SINGLE VOLUTE CASING ND-3423-2 TYPICAL DOUBLE VOLUTE CASING ND-3416-1 STRESS AND PRESSURE LIMITS FOR DESIGN AND SERVICE LOADINGS |
| 114 | ND- 3430 DESIGN REQUIREMENTS FOR CENTRIFUGAL PUMPS ND-3433.4-1 MINIMUM TANGENTIAL INLET AND OUTLET WALL THICKNESSES |
| 115 | ND- 3440 DESIGN OF SPECIFIC PUMP TYPES ND-3436(c)-1 EXTERNAL AND INTERNAL ATTACHMENTS ND-3441.1-1 TYPE A PUMP |
| 116 | ND-3441.1-2 TYPE A PUMP |
| 117 | ND-3441.1(a)-1 TYPE A PUMP ND-3441.2-1 TYPE B PUMP ND-3441.3-1 TYPE C PUMP |
| 118 | ND-3441.3-2 TYPE C PUMP |
| 119 | ND-3441.4(a)-1 TYPE D PUMP ND-3441.5-1 TYPE E PUMP ND-3441.6(a)-1 TYPE F PUMP ND-3441.7(a)-1 AXIALLY SPLIT CASING, VOLUTE PUMP, TYPE G |
| 120 | ND-3441.7(a)-2 AXIALLY SPLIT CASING, VOLUTE PUMP, TYPE G ND-3441.7(c)-1 AXIALLY SPLIT CASING, VOLUTE PUMP, TYPE G Section B – B Typical Highly Stressed Sections of Pump Case |
| 121 | ND-3441.7(c)(2)-1 TYPICAL SECTION OF TYPE G PUMP ND-3441.7(c)(2)-2 TYPICAL SECTION OF TYPE G PUMP ND-3441.7(c)(2)-3 TYPICAL LOADS ON TYPE G PUMP |
| 123 | ND-3441.8-1 LONGITUDINAL SECTION THROUGH TYPE H PUMP ND-3441.8-2 TRANSVERSE SECTION THROUGH TYPE H PUMP |
| 124 | ND-3441.9-1 TYPE K PUMP |
| 125 | ND-3441.9-2 TYPE K PUMP |
| 128 | ND-3441.10-1 TYPE L PUMP |
| 131 | ND-3441.10-2 TYPE L PUMP BOWL |
| 132 | ND- 3450 DESIGN OF CLASS 3 RECIPROCATING PUMPS ND- 3500 VALVE DESIGN ND- 3510 GENERAL REQUIREMENTS |
| 133 | ND-3451(a)-1 HORIZONTAL SINGLE-ACTING POWER PUMP LIQUID ENDS |
| 135 | ND- 3520 LEVELS B, C, AND D SERVICE LIMITS ND-3521-1 LEVEL A, LEVEL B, LEVEL C, AND LEVEL D SERVICE LIMITS |
| 136 | ND-3521-1 TYPICAL SECTIONS OF VALVE BODIES |
| 137 | ND- 3530 GENERAL RULES ND- 3590 PRESSURE RELIEF VALVE DESIGN |
| 138 | ND-3591.1-1 TYPICAL PRESSURE RELIEF DEVICES |
| 139 | ND-3591.1-2 TYPICAL PRESSURE RELIEF DEVICES |
| 140 | ND-3592.2(b)-1 CLASS 3 PRESSURE RELIEF DEVICES: LEVEL B, C, AND D SERVICE LOADINGS |
| 141 | ND-3595.3-1 VALVE NOZZLE |
| 142 | ND- 3600 PIPING DESIGN ND- 3610 GENERAL REQUIREMENTS ND-3611.2(e)-1 STRESS RANGE REDUCTION FACTORS |
| 144 | ND- 3620 DESIGN CONSIDERATIONS ND-3613.4-1 WELD JOINT EFFICIENCY FACTOR |
| 145 | ND- 3640 PRESSURE DESIGN OF PIPING PRODUCTS. |
| 146 | ND-3622-1 EXAMPLES OF REVERSING AND NONREVERSING DYNAMIC LOADS |
| 147 | ND-3641.1(a)-1 VALUES OF A |
| 148 | ND-3642.1(c)-1 MINIMUM THICKNESS FOR BENDING |
| 149 | ND-3643.2(b)-1 TYPICAL WELDED BRANCH CONNECTIONS |
| 151 | ND-3643.2(b)-2 TYPICAL RIGHT ANGLE BRANCH CONNECTIONS MADE USING A FILLET WELD OR A PARTIAL PENETRATION WELD |
| 152 | ND-3643.3(c)(1)-1 REINFORCEMENT OF BRANCH CONNECTIONS |
| 153 | ND-3643.3(c)(1)-2 SOME REPRESENTATIVE CONFIGURATIONS DESCRIBING THE te REINFORCEMENT DIMENSION |
| 155 | ND-3643.4(a)-1 REINFORCED EXTRUDED OUTLETS |
| 157 | ND-3647.2-1 TYPES OF PERMANENT BLANKS |
| 161 | ND- 3650 ANALYSIS OF PIPING SYSTEMS |
| 163 | ND-3653.3-1 REDUCING OR FULL OUTLET BRANCH CONNECTIONS, OR TEES |
| 166 | ND- 3660 DESIGN OF WELDS ND- 3670 SPECIAL PIPING REQUIREMENTS |
| 169 | ND-3673.2(b)-1 STRESS INDICES, FLEXIBILITY, AND STRESS INTENSIFICATION FACTORS |
| 174 | ND-3673.2(b)-2 BRANCH CONNECTION NOMENCLATURE |
| 176 | ND- 3690 DIMENSIONAL REQUIREMENTS FOR PIPING PRODUCTS ND- 3700 ELECTRICAL AND MECHANICAL PENETRATION ASSEMBLIES ND- 3720 DESIGN RULES ND- 3800 DESIGN OF ATMOSPHERIC STORAGE TANKS ND- 3810 GENERAL REQUIREMENTS ND- 3820 DESIGN CONSIDERATIONS |
| 177 | ND- 3830 BOTTOM DESIGN ND- 3840 SHELL DESIGN ND-3821.5-1 DESIGN AND SERVICE LIMITS |
| 178 | ND- 3850 ROOF DESIGN |
| 180 | ND-3852.7-1 ALLOWABLE TENSILE STRESSES FOR ROOF SUPPORTS |
| 181 | ND-3852.7-2 ALLOWABLE AXIAL COMPRESSION STRESSES FOR ROOF SUPPORTS |
| 183 | D-3852.7-3 ALLOWABLE BENDING STRESSES FOR ROOF SUPPORTS |
| 185 | ND-3852.7-4 ALLOWABLE SHEAR STRESSES FOR ROOF SUPPORTS |
| 186 | ND-3852.7-5 ALLOWABLE SHEAR AND TENSION STRESSES FOR BOLTS FOR ROOF SUPPORTS ND-3852.7-6 ALLOWABLE BEARING STRESSES FOR BOLTS FOR ROOF SUPPORTS |
| 188 | ND-3861-1 ROOF MANHOLES ND-3861-1 ROOF MANHOLES |
| 189 | ND- 3860 TANK CONNECTIONS AND APPURTENANCES ND-3862(a)-1 FLANGED ROOF NOZZLES ND-3862(a)-1 FLANGED ROOF NOZZLES |
| 190 | ND-3862(a)-2 SCREWED OR SOCKET WELD ROOF NOZZLES ND-3862(a)-2 SCREWED OR SOCKET WELD ROOF NOZZLES ND-3863-1 WELDED BOTTOM OUTLET ELBOW |
| 191 | ND- 3900 DESIGN OF 0 psi TO 15 psi ( 0 kPa TO 100 kPa) STORAGE TANKS ND- 3910 GENERAL REQUIREMENTS ND-3863-1 WELDED BOTTOM OUTLET ELBOW |
| 192 | ND- 3920 DESIGN CONSIDERATIONS ND-3865-1 PLATFORMS AND WALKWAYS ND-3865-2 STAIRWAYS |
| 193 | ND-3865-3 STAIRWAY RISE, RUN, AND ANGLE RELATIONSHIPS |
| 194 | ND-3921.8-1 DESIGN AND SERVICE LIMITS FOR STEEL TANKS |
| 195 | ND-3922.1-1 BIAXIAL STRESS CHART FOR COMBINED TENSION AND COMPRESSION, 30,000 psi TO 38,000 psi (205 MPa to 260 MPa) YIELD STRENGTH STEELS |
| 196 | ND-3922.1-2 REDUCTION OF DESIGN STRESSES REQUIRED TO ALLOW FOR BIAXIAL STRESSES OF OPPOSITE SIGN |
| 198 | ND-3923.1-1 MAXIMUM ALLOWABLE STRESS VALUES FOR STRUCTURAL MEMBERS |
| 200 | ND- 3930 DESIGN PROCEDURE |
| 202 | ND-3932.1-1 SOME TYPICAL FREE BODY DIAGRAMS FOR CERTAIN SHAPES OF TANKS |
| 203 | ND-3932.2(d)-1 FACTORS FOR DETERMINING VALUES OF R1 AND R2 FOR 2:1 ELLIPSOIDAL ROOFS AND BOTTOMS |
| 206 | ND-3933.4(a)-1 COMPRESSION RING REGION |
| 208 | ND-3933.5(d)-1 PERMISSIBLE DETAILS OF COMPRESSION RING CONSTRUCTION |
| 209 | ND-3933.5(h)-1 SOME VALUES FOR kBASED ON n, THETA |
| 210 | ARTICLE ND- 4000 FABRICATION AND INSTALLATION ND- 4100 GENERAL REQUIREMENTS ND- 4110 INTRODUCTION ND- 4120 CERTIFICATION OF MATERIAL AND FABRICATION BY COMPONENT CERTIFICATE HOLDER |
| 211 | ND- 4130 REPAIR OF MATERIAL ND- 4200 FORMING, FITTING, AND ALIGNING ND- 4210 CUTTING, FORMING, AND BENDING |
| 212 | ND- 4220 FORMING TOLERANCES |
| 213 | ND-4221.1-1 MAXIMUM DIFFERENCE IN CROSS-SECTIONAL DIAMETERS |
| 214 | ND-4221.2(a)-1 MAXIMUM PERMISSIBLE DEVIATION eFROM A TRUE CIRCULAR FORM |
| 215 | ND- 4230 FITTING AND ALIGNING ND-4221.2(a)-2 MAXIMUM ARC LENGTH FOR DETERMINING PLUS OR MINUS DEVIATION |
| 216 | ND-4233-1 BUTT WELD ALIGNMENT AND MISMATCH TOLERANCES FOR UNEQUAL I.D. AND O.D. WHEN COMPONENTS ARE WELDED FROM ONE SIDE AND FAIRING IS NOT PERFORMED ND-4232(a)-1 MAXIMUM ALLOWABLE OFFSET IN FINAL WELDED JOINTS |
| 217 | ND- 4240 REQUIREMENTS FOR WELD JOINTS IN COMPONENTS |
| 218 | ND-4243-1 ATTACHMENT OF PRESSURE PARTS TO PLATES TO FORM A CORNER JOINT |
| 220 | ND-4243.1-1 TYPICAL FLAT HEADS, AND SUPPORTED AND UNSUPPORTED TUBESHEETS WITH HUBS |
| 221 | ND-4244(a)-1 NOZZLES, AND BRANCH AND PIPING CONNECTIONS JOINED BY FULL PENETRATION BUTT WELDS |
| 222 | ND-4244(b)-1 NOZZLES, AND BRANCH AND PIPING CONNECTIONS JOINED BY FULL PENETRATION CORNER WELDS |
| 223 | ND-4244(c)-1 DEPOSITED WELD METAL USED AS REINFORCEMENT OF OPENINGS FOR NOZZLES, AND BRANCH AND PIPING CONNECTIONS |
| 225 | ND-4244(d)-1 SOME ACCEPTABLE TYPES OF WELDED NOZZLES, AND BRANCH AND PIPING CONNECTIONS |
| 226 | ND-4244(e)-1 SOME ACCEPTABLE TYPES OF WELDED NOZZLES |
| 227 | ND-4244(e)-2 SOME ACCEPTABLE TYPES OF SMALL FITTINGS |
| 228 | ND-4244(f)-1 TUBE CONNECTIONS |
| 229 | ND-4244(g)-1 SOME ACCEPTABLE TYPES OF WELDED NOZZLES, AND BRANCH AND PIPING CONNECTIONS |
| 230 | ND-4245-1 ATTACHMENT WELDS |
| 232 | ND-4246.1(a)-1 TYPICAL BOTTOM AND BOTTOM-TO-SHELL JOINTS |
| 233 | ND-4246.3-1 TYPICAL ROOF AND ROOF-TO-SHELL JOINTS |
| 234 | ND-4246.5-1 ROOF MANHOLES |
| 235 | ND-4246.5-2 FLANGED ROOF NOZZLES ND-4246.5-3 SCREWED OR SOCKET WELD ROOF NOZZLES ND-4246.5-4 WELDED BOTTOM OUTLET ELBOW |
| 236 | ND- 4250 WELDING END TRANSITIONS — MAXIMUM ENVELOPE ND- 4300 WELDING QUALIFICATIONS ND- 4310 GENERAL REQUIREMENTS ND-4247.6(d)-1 MINIMUM SIZE FOR FILLET WELDS |
| 237 | ND-4250-1 WELDING END TRANSITIONS MAXIMUM ENVELOPE |
| 238 | ND- 4320 WELDING QUALIFICATIONS, RECORDS, AND IDENTIFYING STAMPS ND- 4330 GENERAL REQUIREMENTS FOR WELDING PROCEDURE QUALIFICATION TESTS |
| 241 | ND- 4350 SPECIAL QUALIFICATION REQUIREMENTS FOR TUBE- TO-TUBESHEET WELDS ND- 4400 RULES GOVERNING MAKING, EXAMINING, AND REPAIRING WELDS ND- 4410 PRECAUTIONS TO BE TAKEN BEFORE WELDING ND- 4420 RULES FOR MAKING WELDED JOINTS |
| 242 | ND- 4430 WELDING OF ATTACHMENTS |
| 243 | ND-4427-1 FILLET AND SOCKET WELD DETAILS AND DIMENSIONS |
| 244 | ND-4433-1 TYPES OF ATTACHMENT WELDS |
| 245 | ND- 4450 REPAIR OF WELD METAL DEFECTS ND-4437.2(b)-1 SOME ACCEPTABLE METHODS OF ATTACHING STIFFENING RINGS TO SHELLS OF CYLINDRICAL VESSELS SUBJECTED TO EXTERNAL PRESSURE |
| 246 | ND- 4460 WELDED TEST PLATES ND- 4470 WELDED STAYED CONSTRUCTION ND- 4500 BRAZING ND- 4510 RULES FOR BRAZING |
| 247 | ND- 4520 BRAZING QUALIFICATION REQUIREMENTS ND-4470-1 WELDED STAYED CONSTRUCTION |
| 248 | ND-4511-1 BRAZED CONNECTIONS FOR APPURTENANCES AND PIPING, NPS 4 (DN 100) AND LESS |
| 249 | ND- 4530 FITTING AND ALIGNING OF PARTS TO BE BRAZED ND- 4540 EXAMINATION OF BRAZED JOINTS ND- 4600 HEAT TREATMENT ND- 4610 WELDING PREHEAT REQUIREMENTS ND-4524-1 MAXIMUM DESIGN TEMPERATURES FOR BRAZING FILLER METAL, °F (°C) |
| 250 | ND- 4620 POSTWELD HEAT TREATMENT |
| 251 | ND-4622.1-1 MANDATORY REQUIREMENTS FOR POSTWELD HEAT TREATMENT OF WELDS |
| 252 | ND-4622.4(c)-1 ALTERNATIVE HOLDING TEMPERATURES AND TIMES |
| 253 | ND-4622.7(b)-1 EXEMPTIONS TO MANDATORY PWHT |
| 255 | ND- 4630 HEAT TREATMENT OF WELDS OTHER THAN THE FINAL POSTWELD HEAT TREATMENT ND- 4650 HEAT TREATMENT AFTER BENDING OR FORMING FOR PIPE, PUMPS, AND VALVES |
| 256 | ND- 4660 HEAT TREATMENT OF ELECTROSLAG WELDS ND- 4700 MECHANICAL JOINTS ND- 4710 BOLTING AND THREADING ND- 4720 BOLTING FLANGED JOINTS ND- 4730 ELECTRICAL AND MECHANICAL PENETRATION ASSEMBLIES ND- 4800 EXPANSION JOINTS ND- 4810 FABRICATION AND INSTALLATION RULES FOR BELLOWS EXPANSION JOINTS |
| 257 | ND-4730-1 PENETRATION ASSEMBLY ND-4810(c)-1 PERMISSIBLE ATTACHMENT WELDS FOR BELLOWS |
| 258 | ARTICLE ND- 5000 EXAMINATION ND- 5100 GENERAL REQUIREMENTS FOR EXAMINATION ND- 5110 PROCEDURES, QUALIFICATIONS, AND EVALUATION ND- 5120 TIME OF EXAMINATION OF WELDS AND WELD METAL CLADDING |
| 259 | ND- 5200 EXAMINATION OF WELDS ND- 5210 CATEGORY A VESSEL WELDED JOINTS IN VESSELS AND SIMILAR WELDED JOINTS IN PIPING, PUMPS, AND VALVES ND- 5220 CATEGORY B VESSEL WELDED JOINTS AND CIRCUMFERENTIAL WELDED JOINTS IN PIPING, PUMPS, AND VALVES ARTICLE ND- 5000 TABLE ND-5211.2-1 THICKNESS ABOVE WHICH FULL RADIOGRAPHIC EXAMINATION OF BUTT WELDED JOINT IS MANDATORY |
| 260 | ND- 5230 CATEGORY C VESSEL WELDED JOINTS AND SIMILAR WELDED JOINTS IN PIPING, PUMPS, AND VALVES ND- 5240 CATEGORY D VESSEL WELDED JOINTS AND SIMILAR JOINTS IN PIPING, PUMPS, AND VALVES ND- 5260 WELDED STAYED CONSTRUCTION |
| 261 | ND- 5270 SPECIAL WELDS ND- 5280 WELDED JOINTS IN STORAGE TANKS |
| 262 | ND- 5300 ACCEPTANCE STANDARDS ND- 5320 RADIOGRAPHIC ACCEPTANCE STANDARDS |
| 263 | ND- 5330 ULTRASONIC ACCEPTANCE STANDARDS ND- 5340 MAGNETIC PARTICLE ACCEPTANCE STANDARDS |
| 264 | ND- 5350 LIQUID PENETRANT ACCEPTANCE STANDARDS ND- 5360 VISUAL ACCEPTANCE STANDARDS FOR BRAZED JOINTS ND- 5380 GAS AND BUBBLE FORMATION TESTING ND- 5400 SPOT EXAMINATION OF WELDED JOINTS ND- 5410 GENERAL REQUIREMENTS ND- 5420 MINIMUM EXTENT OF SPOT RADIOGRAPHIC EXAMINATION |
| 265 | ND- 5430 STANDARDS FOR SPOT RADIOGRAPHIC EXAMINATION ND- 5440 EVALUATION AND RETESTS ND- 5500 QUALIFICATIONS AND CERTIFICATION OF NONDESTRUCTIVE EXAMINATION PERSONNEL ND- 5510 GENERAL REQUIREMENTS ND- 5520 PERSONNEL QUALIFICATION, CERTIFICATION, AND VERIFICATION |
| 266 | ND- 5530 RECORDS ND- 5700 EXAMINATION REQUIREMENTS FOR EXPANSION JOINTS ND- 5720 BELLOWS EXPANSION JOINTS |
| 268 | ARTICLE ND- 6000 TESTING ND- 6100 GENERAL REQUIREMENTS ND- 6110 PRESSURE TESTING OF COMPONENTS, APPURTENANCES, AND SYSTEMS |
| 269 | ND- 6120 PREPARATION FOR TESTING |
| 270 | ND- 6200 HYDROSTATIC TESTS ND- 6210 HYDROSTATIC TEST PROCEDURE ND- 6220 HYDROSTATIC TEST PRESSURE REQUIREMENTS ND- 6230 BELLOWS EXPANSION JOINTS |
| 271 | ND- 6240 PROVISION FOR EMBEDDED OR INACCESSIBLE WELDED JOINTS IN PIPING ND- 6300 PNEUMATIC TESTS ND- 6310 PNEUMATIC TESTING PROCEDURES ND- 6320 PNEUMATIC TEST PRESSURE REQUIREMENTS ND- 6330 BELLOWS EXPANSION JOINTS ND- 6400 PRESSURE TEST GAGES ND- 6410 REQUIREMENTS FOR PRESSURE TEST GAGES |
| 272 | ND- 6500 ATMOSPHERIC AND 0 psig TO 15 psig ( 0 kPa TO 100 kPa) STORAGE TANKS ND- 6510 TESTING OF ATMOSPHERIC STORAGE TANKS ND- 6520 TESTING OF 0 psig TO 15 psig ( 0 kPa TO 100 kPa) STORAGE TANKS |
| 273 | ND- 6530 TEST GAGES |
| 274 | ND- 6600 SPECIAL TEST PRESSURE SITUATIONS ND- 6610 COMPONENTS DESIGNED FOR EXTERNAL PRESSURE ND- 6620 PRESSURE TESTING OF COMBINATION UNITS ND- 6900 PROOF TESTS TO ESTABLISH DESIGN PRESSURE ND- 6910 GENERAL REQUIREMENTS |
| 275 | ND- 6920 PROCEDURES |
| 278 | ND- 6930 PROCEDURE FOR COMPONENTS HAVING CHAMBERS OF SPECIAL SHAPE SUBJECT TO COLLAPSE |
| 279 | ARTICLE ND- 7000 OVERPRESSURE PROTECTION ND- 7100 GENERAL REQUIREMENTS ND- 7110 SCOPE ND- 7120 INTEGRATED OVERPRESSURE PROTECTION ND- 7130 VERIFICATION OF THE OPERATION OF RECLOSING PRESSURE RELIEF DEVICES ND- 7140 INSTALLATION |
| 280 | ND- 7150 ACCEPTABLE PRESSURE RELIEF DEVICES |
| 281 | ND- 7160 UNACCEPTABLE PRESSURE RELIEF DEVICES ND- 7170 PERMITTED USE OF PRESSURE RELIEF DEVICES ND- 7200 OVERPRESSURE PROTECTION REPORT ND- 7210 RESPONSIBILITY FOR REPORT ND- 7220 CONTENT OF REPORT |
| 282 | ND- 7230 CERTIFICATION OF REPORT ND- 7240 REVIEW OF REPORT AFTER INSTALLATION ND- 7250 FILING OF REPORT ND- 7300 RELIEVING CAPACITY REQUIREMENTS ND- 7310 EXPECTED SYSTEM PRESSURE TRANSIENT CONDITIONS |
| 283 | ND- 7320 UNEXPECTED SYSTEM EXCESS PRESSURE TRANSIENT CONDITIONS ND- 7330 SYSTEM FAULTED CONDITIONS ND- 7400 SET PRESSURES OF PRESSURE RELIEF DEVICES ND- 7410 SET PRESSURE LIMITATIONS FOR EXPECTED SYSTEM PRESSURE TRANSIENT CONDITIONS ND- 7420 SET PRESSURE LIMITATIONS FOR UNEXPECTED SYSTEM EXCESS PRESSURE TRANSIENT CONDITIONS ND- 7500 OPERATING AND DESIGN REQUIREMENTS FOR PRESSURE AND VACUUM RELIEF VALVES ND- 7510 SAFETY, SAFETY RELIEF, AND RELIEF VALVES |
| 285 | ND- 7520 PILOT OPERATED PRESSURE RELIEF VALVES |
| 286 | ND- 7530 POWER ACTUATED PRESSURE RELIEF VALVES ND- 7540 SAFETY AND SAFETY RELIEF VALVES WITH AUXILIARY ACTUATING DEVICES ND- 7550 VACUUM RELIEF VALVES |
| 287 | ND- 7560 ALTERNATIVE TEST MEDIA ND- 7600 NONRECLOSING PRESSURE RELIEF DEVICES ND- 7610 RUPTURE DISK DEVICES |
| 288 | ND- 7620 INSTALLATION REQUIREMENTS ND- 7700 CERTIFICATION ND- 7710 RESPONSIBILITY FOR CERTIFICATION OF PRESSURE AND VACUUM RELIEF VALVES |
| 289 | ND- 7720 RESPONSIBILITY FOR CERTIFICATION OF NONRECLOSING PRESSURE RELIEF DEVICES ND- 7730 CAPACITY CERTIFICATION OF PRESSURE RELIEF VALVES — COMPRESSIBLE FLUIDS |
| 292 | ND-7734.2(a)-1 VALUES OF FFOR NONCHOKING FLOW |
| 293 | ND- 7740 CAPACITY CERTIFICATION OF PRESSURE RELIEF VALVES — INCOMPRESSIBLE FLUIDS |
| 295 | ND- 7750 CAPACITY CERTIFICATION OF VACUUM RELIEF VALVES |
| 297 | ND- 7760 CAPACITY DETERMINATION OF RUPTURE DISK DEVICES ND-7754.2(a)-1 VALUES OF FFOR NONCHOKING FLOW |
| 299 | ND- 7800 MARKING, STAMPING, AND DATA REPORTS ND- 7810 PRESSURE AND VACUUM RELIEF VALVES |
| 300 | ND- 7820 RUPTURE DISK DEVICES ND- 7830 PRESSURE RELIEF VALVE IN COMBINATION WITH RUPTURE DISK DEVICES ND- 7840 CERTIFICATE OF AUTHORIZATION TO USE CODE SYMBOL STAMP |
| 301 | ARTICLE ND- 8000 NAMEPLATES, STAMPING, AND REPORTS ND- 8100 GENERAL REQUIREMENTS |
Related products
-
ICC IRC 2024 1stptg
International Residential Code Published By Publication Date Number of Pages ICC 2024 1123
-
ASME BPVC III 1 ND 2004
ASME BPVC – III – 1 – ND -2004 BPVC Section III, Rules for Constructions…
-
AWWA OpGuide J100 2021
Operational Guide to AWWA Standard J100 Risk & Resilience Management of Water & Wastewater Systems…
-
ASME BPVC III 1 ND 2001
ASME BPVC – III – 1 – ND -2001 BPVC Section III, Rules for Constructions…
-
ASME BPVC III 1 ND 2017
ASME BPVC – III – 1 – ND -2017 BPVC Section III, Rules for Constructions…
-
ASME BPVC III 1 A 2007
ASME BPVC – III – 1 – A -2007 BPVC Section III, Rules for Construction…
