ASME BPVC IV 2019

$377.00

ASME BPVC – IV -2019 BPVC Section IV, Rules for Construction of Heating Boilers

Published By	Publication Date	Number of Pages
ASME	2019	303

Guaranteed Safe Checkout

Category: ASME

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This Section provides requirements for design, fabrication, installation and inspection of steam heating, hot water heating, hot water supply boilers, and potable water heaters intended for low pressure service that are directly fired by oil, gas, electricity, coal or other solid or liquid fuels. It contains appendices which cover approval of new material, methods of checking safety valve and safety relief valve capacity, examples of methods of checking safety valve and safety relief valve capacity, examples of methods of calculation and computation, definitions relating to boiler design and welding, and quality control systems. Rules pertaining to use of the H, HV, and HLW ASME Product Certification Marks are also included. Careful application of this Section will help users to comply with applicable regulations within their jurisdictions, while achieving the operational, cost and safety benefits to be gained from the many industry best-practices detailed within these volumes. Intended for manufacturers, users, constructors, designers and others concerned with the design, fabrication, assembly, erection, examination, inspection and testing of pressure vessels, plus all potential governing entities.

PDF Catalog

PDF Pages	PDF Title
56	HG-307 Some Acceptable Types of Unstayed Flat Heads and Covers
60	HG-309 Spherically Dished Steel Plate Covers With Bolting Flanges
62	HG-312.4 Acceptable Type of Ring-Reinforced Furnace
64	HG-312.7 Connection Between Plain and Corrugated Furnace HG-312.8 Acceptable Type of Semicircular Furnace Reinforcement
66	HG-321 Chart for Determining Values of F HG-321 Values of Spherical Radius Factor K1
69	HG-326.1 Some Representative Configurations Describing the Reinforcement Dimension, te, and the Finished Opening Dimension, d
70	HG-326.2 Nomenclature and Formulas for Reinforced Openings
72	HG-340.1 Pitch of Staybolts Adjacent to Upper Corners of Fireboxes
73	HG-340.2 Acceptable Proportions for Ends of Through‐Stays HG-340.3 Examples of Acceptable Corner Welds for Pressures Not Over 30 psi
74	HG-340 Allowable Pitch of Stays, in. (mm) (Limited by HG-340.3)
76	HG-343 Details of Installation of Diagonal Stays
77	HG-345.1(a) Sketch Showing Application of HG-345.1 to the Staying of Boilers
78	HG-345.1(b) Sketch Showing Application of HG-345.1 to the Staying of Boilers
80	HG-350.1 Example of Tube Spacing With Pitch of Holes Equal in Every Row HG-350.2 Example of Tube Spacing With Pitch of Holes Unequal in Every Second Row
81	HG-350.3 Example of Tube Spacing With Pitch of Holes Varying in Every Second and Third Row HG-350.4 Example of Tube Spacing With Tube Holes on Diagonal Lines
82	HG-360 Permitted O‐Ring Materials HG-370 Minimum Thickness of Material for Threaded Connections to Boilers
86	HG-402 Official Certification Mark to Denote the American Society of Mechanical Engineers’ Standard
96	HG-530.1 Official Certification Mark to Denote the American Society of Mechanical Engineers’ Standard HG-530.2 Steam and Water Boilers Form of Marking on Completed Boilers or Their Nameplates
97	HG-530.3 Boilers Suitable for Water Only HG-530.4 Steam and Water Boilers
98	HG-530.5 Boilers Suitable for Water Only HG-530.6 Boilers Suitable for Water Only
99	HG-530.7 Steam and Water Boilers HG-530.8 Boilers Suitable for Water Only
100	HG-531.1 Form of Marking on Part or Accessory — H Designator HG-531.2 Form of Marking on Part or Accessory — PRT Designator
109	HG-703.1(a) Steam Boilers in Battery — Pumped Return — Acceptable Piping Installation
110	HG-703.1(b) Steam Boilers in Battery — Gravity Return — Acceptable Piping Installation
111	HG-703.2 Hot Water Boilers in Battery — Acceptable Piping Installation
113	HG-709.2 Expansion Tank Capacities for Forced Hot Water Systems
114	HG-715 Size of Bottom Blowoff Piping, Valves, and Cocks
115	HG-725(a) Spacing and Weld Details for Supporting Lugs in Pairs on Horizontal‐Return Tubular Boiler
116	HG-725(b) Welded Bracket Connection for Horizontal‐Return Tubular Boiler
123	HF-300.1 Maximum Allowable Stress Values for Ferrous Materials, ksi
129	HF-300.1M Maximum Allowable Stress Values for Ferrous Materials, MPa
135	HF-300.2 Maximum Allowable Stress Values for Nonferrous Materials, ksi
140	HF-300.2M Maximum Allowable Stress Values for Nonferrous Materials, MPa
148	HW-701.1 Butt Welding of Plates of Unequal Thickness
150	HW-701.3 Some Forms of Attachments of Pressure Parts to Flat Plates to Form a Corner Joint (Tee Joint)
151	HW-710.4(a) Some Acceptable Types of Diagonal Stays for Installation by Welding HW-710.4(b) Unacceptable Types of Diagonal Stays for Installation by Welding
153	HW-715.1 Heads Attached to Shells HW-713 Firetube Extension Through Tubesheets for Welded Construction
155	HW-731 Some Acceptable Types of Welds for Fittings, Nozzles, and Other Connections to Shells, Drums, and Headers
158	HW-740 Three‐Ply Joint Assemblies
161	HW-745 Two‐Ply Joint Assemblies
170	HB-1305 Recommended Joint Clearances at Brazing Temperature
175	HC-204.1 Dimensions of Tensile Test Specimen HC-205.1 Cast Test Bars
177	HC-212 Correction Factors for Transverse Test Bars
178	HC-214 Pipe Plug Size for Minimum Wall Thickness
179	HC-300 Maximum Allowable Stress Values in Tension for Cast Iron, ksi (MPa)
180	HC-311 Spherically Shaped Covers With Bolting Flanges
205	HLW-300 Maximum Allowable Stress Values in Tension for Lined Water Heater Materials, ksi (MPa)
207	HLW-301 Maximum Allowable Stress Values in Tension for Unlined Water Heater Materials, ksi (MPa)
211	HLW-401.1 Butt Welding of Plates of Unequal Thickness
212	HLW-401.2 Typical Corner Joints HLW-401.3-1 Alignment Tolerance
214	HLW-411 Typical Water Heater Welded Joints
216	HLW-413 Tubes Attached by Welding
217	HLW-415 Heads Attached to Shells
219	HLW-431.1 Some Acceptable Types of Welds for Fittings, Nozzles, and Other Connections to Shells and Head
220	HLW-431.5 Some Acceptable Types of Welds for Fittings, Nozzles, and Other Connections to Shells and Head
223	HLW-432.1 Some Acceptable Types of Brazed Fittings, Nozzles, and Other Connections to Copper‐Lined Shells and Heads
229	HLW-602.1 Official Symbol to Denote The American Society of Mechanical Engineers’ Standard HLW-602.2 Form of Stamping on Completed Water Heaters
233	HLW-809.1 Expansion Tank Capacities for a Water Heater
234	HLW-809.1 A Typical Acceptable Piping Installation for Storage Water Heaters in Battery
235	HLW-809.2 A Typical Acceptable Piping Installation for Flow Through Water Heater With Provisions for Piping Expansion
237	2-100 Codes, Standards, and Specifications Referenced in Text
241	4-1 Guide for the Preparation of Section IV Manufacturer’s Data Report Forms
244	H-2 Manufacturer’s Data Report for All Types of Boilers Except Watertube and Those Made of Cast Iron
246	H-3 Manufacturer’s Data Report for Watertube Boilers
248	H-4 Manufacturer’s Partial Data Report
250	H-5 Manufacturer’s Master Data Report for Boilers Constructed from Cast Iron
252	H-5A Manufacturer’s Master Data Report for Boilers Constructed from Cast Aluminum
254	H-6 Manufacturer’s Data Report Supplementary Sheet
255	HC-1 Manufacturer’s Material Certificate of Conformance for Cast Iron Boiler Sections
256	HC-2 Manufacturer’s Material Certificate of Conformance for Hydrostatic Testing of Cast Iron Boiler Sections
257	HC-3 Manufacturer’s Report for the Application of Nameplates on Cast Iron Boilers
258	HA-1 Manufacturer’s Material Certificate of Conformance for Cast Aluminum Boiler Sections
259	HA-2 Manufacturer’s Material Certificate of Conformance for Hydrostatic Testing of Cast Aluminum Boiler Sections
260	HA-3 Manufacturer’s Report for the Application of Nameplates on Cast Aluminum Boilers
261	HLW-6 Manufacturer’s Data Report for Water Heaters or Storage Tanks
263	HLW-7 Manufacturer’s Partial Data Report for Water Heaters and Storage Tanks
265	HLW-8 Manufacturer’s Master Data Proof Test Report for Water Heaters or Storage Tanks
268	6-1 Standard Units for Use in Equations
272	8-1 Certificate of Conformance for Reapplication of the Certification Mark
273	8-200-1 Guide for Completing the Certificate of Conformance for Reapplication of the Certification Mark
277	A-100 Guide for Estimating Steaming Capacity Based on Heating Surface
281	D-100 Computation of Typical Pad Reinforcement
282	D-101 Computation of a Typical Nozzle Fitting
293	K-1 Sample Certificate of Authorization
298	N-1 Guide for the Preparation of Section IV Manufacturer’s Certificate of Conformance Form HV-1
299	HV-1 Manufacturer’s Certificate of Conformance for Pressure Relief Valves