ASME BPVC VIII 1 2007

$377.00

ASME BPVC – VIII – 1 -2007 BPVC Section VIII-Rules for Construction of Pressure Vessels Division 1

Published By	Publication Date	Number of Pages
ASME	2007	778

Guaranteed Safe Checkout

Category: ASME

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

PDF Catalog

PDF Pages	PDF Title
4	LIST OF BPVC SECTIONS
6	CONTENTS
8	PART UG FIGURES PART UG TABLES
10	PART UW FIGURES PART UW TABLES
13	PART UB FIGURES PART UB TABLES
14	PART UCS FIGURES PART UCS TABLES
16	PART UNF TABLES
17	PART UHA TABLES
18	PART UCI TABLES
19	PART UCD TABLES
20	PART UHT FIGURES PART UHT TABLES
22	PART ULW FIGURES
23	PART ULT TABLES PART UHX FIGURES PART UHX TABLES
26	FOREWORD
28	STATEMENTS OF POLICY
30	PERSONNEL
42	SUMMARY OF CHANGES
46	LIST OF CHANGES IN BC ORDER
48	INTRODUCTION
55	SUBSECTION A GENERAL REQUIREMENTS PART UG GENERAL REQUIREMENTS FOR ALL METHODS OF CONSTRUCTION AND ALL MATERIALS UG- 1 SCOPE MATERIALS UG- 4 GENERAL
56	UG- 5 PLATE2 UG- 6 FORGINGS UG- 7 CASTINGS UG- 8 PIPE AND TUBES
57	UG- 9 WELDING MATERIALS UG- 10 MATERIAL IDENTIFIED WITH OR PRODUCED TO A SPECIFICATION NOT PERMITTED BY THIS DIVISION, AND MATERIAL NOT FULLY IDENTIFIED
58	UG- 11 PREFABRICATED OR PREFORMED PRESSURE PARTS
60	UG- 12 BOLTS AND STUDS UG- 13 NUTS AND WASHERS UG- 14 RODS AND BARS UG- 15 PRODUCT SPECIFICATION DESIGN UG- 16 GENERAL
61	UG- 17 METHODS OF FABRICATION IN COMBINATION UG- 18 MATERIALS IN COMBINATION UG- 19 SPECIAL CONSTRUCTIONS
62	UG- 20 DESIGN TEMPERATURE UG- 21 DESIGN PRESSURE8
63	UG- 22 LOADINGS UG- 23 MAXIMUM ALLOWABLE STRESS VALUES9
64	UG- 24 CASTINGS
65	UG- 25 CORROSION
66	UG- 26 LININGS UG- 27 THICKNESS OF SHELLS UNDER INTERNAL PRESSURE UG- 28 THICKNESS OF SHELLS AND TUBES UNDER EXTERNAL PRESSURE
67	UG-28 DIAGRAMMATIC REPRESENTATION OF VARIABLES FOR DESIGN OF CYLINDRICAL VESSELS SUBJECTED TO EXTERNAL PRESSURE
68	UG-28.1 DIAGRAMMATIC REPRESENTATION OF LINES OF SUPPORT FOR DESIGN OF CYLINDRICAL VESSELS SUBJECTED TO EXTERNAL PRESSURE
70	UG- 29 STIFFENING RINGS FOR CYLINDRICAL SHELLS UNDER EXTERNAL PRESSURE
72	UG-29.1 VARIOUS ARRANGEMENTS OF STIFFENING RINGS FOR CYLINDRICAL VESSELS SUBJECTED TO EXTERNAL PRESSURE
73	UG-29.2 MAXIMUM ARC OF SHELL LEFT UNSUPPORTED BECAUSE OF GAP IN STIFFENING RING OF CYLINDRICAL SHELL UNDER EXTERNAL PRESSURE
74	UG- 30 ATTACHMENT OF STIFFENING RINGS UG- 31 TUBES, AND PIPE WHEN USED AS TUBES OR SHELLS UG- 32 FORMED HEADS, AND SECTIONS, PRESSURE ON CONCAVE SIDE
75	UG-30 SOME ACCEPTABLE METHODS OF ATTACHING STIFFENING RINGS
77	UG- 33 FORMED HEADS, PRESSURE ON CONVEX SIDE
78	UG-33.1 VALUES OF SPHERICAL RADIUS FACTOR Ko FOR ELLIPSOIDAL HEAD WITH PRESSURE ON CONVEX SIDE
79	UG-33.1 LENGTH LOF SOME TYPICAL CONICAL SECTIONS FOR EXTERNAL PRESSURE
80	UG- 34 UNSTAYED FLAT HEADS AND COVERS
81	UG-34 SOME ACCEPTABLE TYPES OF UNSTAYED FLAT HEADS AND COVERS
84	UG- 35 OTHER TYPES OF CLOSURES
85	OPENINGS AND REINFORCEMENTS UG- 36 OPENINGS IN PRESSURE VESSELS
86	UG-36 LARGE HEAD OPENINGS — REVERSE-CURVE AND CONICAL SHELL-REDUCER SECTIONS
87	UG- 37 REINFORCEMENT REQUIRED FOR OPENINGS IN SHELLS AND FORMED HEADS
88	UG-37 CHART FOR DETERMINING VALUE OF F, AS REQUIRED IN UG-37
89	UG-37.1 NOMENCLATURE AND FORMULAS FOR REINFORCED OPENINGS
90	UG- 38 FLUED OPENINGS IN SHELLS AND FORMED HEADS UG-37 VALUES OF SPHERICAL RADIUS FACTOR K1
91	UG- 39 REINFORCEMENT REQUIRED FOR OPENINGS IN FLAT HEADS UG-38 MINIMUM DEPTH FOR FLANGE OF FLUED-IN OPENINGS
92	UG- 40 LIMITS OF REINFORCEMENT
93	UG-39 MULTIPLE OPENINGS IN RIM OF HEADS WITH A LARGE CENTRAL OPENING
94	UG-40 SOME REPRESENTATIVE CONFIGURATIONS DESCRIBING THE REINFORCEMENT DIMENSION te AND THE OPENING DIMENSION d
96	UG- 41 STRENGTH OF REINFORCEMENT UG- 42 REINFORCEMENT OF MULTIPLE OPENINGS UG- 43 METHODS OF ATTACHMENT OF PIPE AND NOZZLE NECKS TO VESSEL WALLS
97	UG-41.1 NOZZLE ATTACHMENT WELD LOADS AND WELD STRENGTH PATHS TO BE CONSIDERED
99	UG-42 EXAMPLES OF MULTIPLE OPENINGS UG-43 MINIMUM NUMBER OF PIPE THREADS FOR CONNECTIONS
100	UG- 44 FLANGES AND PIPE FITTINGS UG- 45 NOZZLE NECK THICKNESS
101	UG- 46 INSPECTION OPENINGS
102	BRACED AND STAYED SURFACES UG- 47 BRACED AND STAYED SURFACES UG-47 ACCEPTABLE PROPORTIONS FOR ENDS OF STAYS
103	UG- 48 STAYBOLTS UG- 49 LOCATION OF STAYBOLTS UG- 50 DIMENSIONS OF STAYBOLTS LIGAMENTS UG- 53 LIGAMENTS
104	UG-53.1 EXAMPLE OF TUBE SPACING WITH PITCH OF HOLES EQUAL IN EVERY ROW UG-53.2 EXAMPLE OF TUBE SPACING WITH PITCH OF HOLES UNEQUAL IN EVERY SECOND ROW UG-53.3 EXAMPLE OF TUBE SPACING WITH PITCH OF HOLES VARYING IN EVERY SECOND AND THIRD ROW
105	UG-53.4 EXAMPLE OF TUBE SPACING WITH TUBE HOLES ON DIAGONAL LINES
106	UG-53.5 DIAGRAM FOR DETERMINING THE EFFICIENCY OF LONGITUDINAL AND DIAGONAL LIGAMENTS BETWEEN OPENINGS IN CYLINDRICAL SHELLS
107	UG-53.6 DIAGRAM FOR DETERMINING EQUIVALENT LONGITUDINAL EFFICIENCY OF DIAGONAL LIGAMENTS BETWEEN OPENINGS IN CYLINDRICAL SHELLS
108	UG- 54 SUPPORTS UG- 55 LUGS FOR PLATFORMS, LADDERS, AND OTHER ATTACHMENTS TO VESSEL WALLS FABRICATION UG- 75 GENERAL UG- 76 CUTTING PLATES AND OTHER STOCK UG- 77 MATERIAL IDENTIFICATION ( SEE UG- 85) UG- 78 REPAIR OF DEFECTS IN MATERIALS
109	UG- 79 FORMING SHELL SECTIONS AND HEADS UG- 80 PERMISSIBLE OUT- OF- ROUNDNESS OF CYLINDRICAL, CONICAL, AND SPHERICAL SHELLS
110	UG-80.1 MAXIMUM PERMISSIBLE DEVIATION FROM A CIRCULAR FORM eFOR VESSELS UNDER EXTERNAL PRESSURE UG-80.2 EXAMPLE OF DIFFERENCES BETWEEN MAXIMUM AND MINIMUM INSIDE DIAMETERS IN CYLINDRICAL, CONICAL, AND SPHERICAL SHELLS
111	UG- 81 TOLERANCE FOR FORMED HEADS UG- 82 LUGS AND FITTING ATTACHMENTS UG- 83 HOLES FOR SCREW STAYS UG- 84 CHARPY IMPACT TESTS UG-84 SIMPLE BEAM IMPACT TEST SPECIMENS (CHARPY TYPE TEST)
113	UG-84.1 CHARPY V-NOTCH IMPACT TEST REQUIREMENTS FOR FULL SIZE SPECIMENS FOR CARBON AND LOW ALLOY STEELS, HAVING A SPECIFIED MINIMUM TENSILE STRENGTH OF LESS THAN 95 ksi, LISTED IN TABLE UCS-23
114	UG-84.1M CHARPY V-NOTCH IMPACT TEST REQUIREMENTS FOR FULL SIZE SPECIMENS FOR CARBON AND LOW ALLOY STEELS, HAVING A SPECIFIED MINIMUM TENSILE STRENGTH OF LESS THAN 655 MPa, LISTED IN TABLE UCS-23
115	UG-84.2 CHARPY IMPACT TEST TEMPERATURE REDUCTION BELOW MINIMUM DESIGN METAL TEMPERATURE UG-84.3 SPECIFICATIONS FOR IMPACT TESTED MATERIALS IN VARIOUS PRODUCT FORMS UG-84.4 IMPACT TEST TEMPERATURE DIFFERENTIAL
117	UG- 85 HEAT TREATMENT INSPECTION AND TESTS UG- 90 GENERAL
118	UG- 91 THE INSPECTOR
119	UG- 92 ACCESS FOR INSPECTOR UG- 93 INSPECTION OF MATERIALS
120	UG- 94 MARKING ON MATERIALS UG- 95 EXAMINATION OF SURFACES DURING FABRICATION UG- 96 DIMENSIONAL CHECK OF COMPONENT PARTS UG- 97 INSPECTION DURING FABRICATION UG- 98 MAXIMUM ALLOWABLE WORKING PRESSURE UG- 99 STANDARD HYDROSTATIC TEST
122	UG- 100 PNEUMATIC TEST35 ( SEE UW- 50) UG- 101 PROOF TESTS TO ESTABLISH MAXIMUM ALLOWABLE WORKING PRESSURE
127	UG- 102 TEST GAGES UG- 103 NONDESTRUCTIVE TESTING
128	MARKING AND REPORTS UG- 115 GENERAL UG- 116 REQUIRED MARKING UG-116 OFFICIAL SYMBOLS FOR STAMP TO DENOTE THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS’ STANDARD
129	UG- 117 CERTIFICATES OF AUTHORIZATION AND CODE SYMBOL STAMPS
132	UG- 118 METHODS OF MARKING UG- 119 NAMEPLATES UG-118 FORM OF STAMPING
133	UG- 120 DATA REPORTS
134	PRESSURE RELIEF DEVICES UG- 125 GENERAL
135	UG- 126 PRESSURE RELIEF VALVES UG- 127 NONRECLOSING PRESSURE RELIEF DEVICES
138	UG- 128 LIQUID PRESSURE RELIEF VALVES UG- 129 MARKING UG-129.1 OFFICIAL SYMBOL FOR STAMP TO DENOTE THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS’ STANDARD FOR PRESSURE RELIEF VALVES
139	UG- 130 CODE SYMBOL STAMP UG- 131 CERTIFICATION OF CAPACITY OF PRESSURE RELIEF DEVICES UG-129.2 OFFICIAL SYMBOL FOR STAMP TO DENOTE THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS’ STANDARD FOR RUPTURE DISK DEVICES
143	UG- 132 CERTIFICATION OF CAPACITY OF PRESSURE RELIEF VALVES IN COMBINATION WITH NONRECLOSING PRESSURE RELIEF DEVICES
144	UG- 133 DETERMINATION OF PRESSURE RELIEVING REQUIREMENTS UG- 134 PRESSURE SETTINGS AND PERFORMANCE REQUIREMENTS
145	UG- 135 INSTALLATION UG- 136 MINIMUM REQUIREMENTS FOR PRESSURE RELIEF VALVES
149	UG- 137 MINIMUM REQUIREMENTS FOR RUPTURE DISK DEVICES
152	SUBSECTION B REQUIREMENTS PERTAINING TO METHODS OF FABRICATION OF PRESSURE VESSELS PART UW REQUIREMENTS FOR PRESSURE VESSELS FABRICATED BY WELDING GENERAL UW-1 SCOPE UW-2 SERVICE RESTRICTIONS
153	UW-3 WELDED JOINT CATEGORY
154	MATERIALS UW- 5 GENERAL DESIGN UW- 8 GENERAL UW- 9 DESIGN OF WELDED JOINTS
155	UW-3 ILLUSTRATION OF WELDED JOINT LOCATIONS TYPICAL OF CATEGORIES A, B, C, AND D UW-9 BUTT WELDING OF PLATES OF UNEQUAL THICKNESS
156	UW- 10 POSTWELD HEAT TREATMENT UW- 11 RADIOGRAPHIC AND ULTRASONIC EXAMINATION
157	UW- 12 JOINT EFFICIENCIES UW- 13 ATTACHMENT DETAILS
159	UW-12 MAXIMUM ALLOWABLE JOINT EFFICIENCIES FOR ARC AND GAS WELDED JOINTS
160	UW-13.1 HEADS ATTACHED TO SHELLS
163	UW-13.2 ATTACHMENT OF PRESSURE PARTS TO FLAT PLATES TO FORM A CORNER JOINT
165	UW- 14 OPENINGS IN OR ADJACENT TO WELDS UW-13.3 TYPICAL PRESSURE PARTS WITH BUTT WELDED HUBS
166	UW- 15 WELDED CONNECTIONS UW-13.4 NOZZLE NECKS ATTACHED TO PIPING OF LESSER WALL THICKNESS UW-13.5 FABRICATED LAP JOINT STUB ENDS
167	UW- 16 MINIMUM REQUIREMENTS FOR ATTACHMENT WELDS AT OPENINGS
168	UW-16.1 SOME ACCEPTABLE TYPES OF WELDED NOZZLES AND OTHER CONNECTIONS TO SHELLS, HEADS, ETC.
174	UW-16.2 SOME ACCEPTABLE TYPES OF SMALL STANDARD FITTINGS
176	UW- 17 PLUG WELDS UW- 18 FILLET WELDS
177	UW- 19 WELDED STAYED CONSTRUCTION UW-19.1 TYPICAL FORMS OF WELDED STAYBOLTS UW-19.2 USE OF PLUG AND SLOT WELDS FOR STAYING PLATES
178	UW- 20 TUBE- TO- TUBESHEET WELDS
179	UW-20.1 SOME ACCEPTABLE TYPES OF TUBE-TO-TUBESHEET STRENGTH WELDS
180	UW- 21 FLANGE TO NOZZLE NECK WELDS FABRICATION UW- 26 GENERAL UW-21 WELDS OF SOCKET WELD FLANGES TO NOZZLE NECKS
181	UW- 27 WELDING PROCESSES UW- 28 QUALIFICATION OF WELDING PROCEDURE UW- 29 TESTS OF WELDERS AND WELDING OPERATORS
182	UW- 30 LOWEST PERMISSIBLE TEMPERATURES FOR WELDING UW- 31 CUTTING, FITTING, AND ALIGNMENT UW- 32 CLEANING OF SURFACES TO BE WELDED UW- 33 ALIGNMENT TOLERANCE
183	UW- 34 SPIN- HOLES UW- 35 FINISHED LONGITUDINAL AND CIRCUMFERENTIAL JOINTS UW-33
184	UW- 36 FILLET WELDS UW- 37 MISCELLANEOUS WELDING REQUIREMENTS UW- 38 REPAIR OF WELD DEFECTS
185	UW- 39 PEENING UW- 40 PROCEDURES FOR POSTWELD HEAT TREATMENT
186	UW- 41 SECTIONING OF WELDED JOINTS
187	UW- 42 SURFACE WELD METAL BUILDUP INSPECTION AND TESTS UW- 46 GENERAL UW- 47 CHECK OF WELDING PROCEDURE UW- 48 CHECK OF WELDER AND WELDING OPERATOR QUALIFICATIONS UW- 49 CHECK OF POSTWELD HEAT TREATMENT PRACTICE UW- 50 NONDESTRUCTIVE EXAMINATION OF WELDS ON PNEUMATICALLY TESTED VESSELS UW- 51 RADIOGRAPHIC EXAMINATION OF WELDED JOINTS
188	UW- 52 SPOT EXAMINATION OF WELDED JOINTS
189	UW- 53 TECHNIQUE FOR ULTRASONIC EXAMINATION OF WELDED JOINTS MARKING AND REPORTS UW- 60 GENERAL PRESSURE RELIEF DEVICES UW- 65 GENERAL
190	PART UF REQUIREMENTS FOR PRESSURE VESSELS FABRICATED BY FORGING GENERAL UF- 1 SCOPE MATERIALS UF- 5 GENERAL UF- 6 FORGINGS UF- 7 FORGED STEEL ROLLS USED FOR CORRUGATING PAPER MACHINERY DESIGN UF- 12 GENERAL
191	UF- 13 HEAD DESIGN UF- 25 CORROSION ALLOWANCE FABRICATION UF- 26 GENERAL UF- 27 TOLERANCES ON BODY FORGINGS UF- 28 METHODS OF FORMING FORGED HEADS UF- 29 TOLERANCE ON FORGED HEADS
192	UF- 30 LOCALIZED THIN AREAS UF- 31 HEAT TREATMENT UF- 32 WELDING FOR FABRICATION
193	UF- 37 REPAIR OF DEFECTS IN MATERIAL
194	UF- 38 REPAIR OF WELD DEFECTS UF- 43 ATTACHMENT OF THREADED NOZZLES TO INTEGRALLY FORGED NECKS AND THICKENED HEADS ON VESSELS INSPECTION AND TESTS UF- 45 GENERAL UF- 46 ACCEPTANCE BY INSPECTOR UF- 47 PARTS FORGING UF- 52 CHECK OF HEAT TREATMENT AND POSTWELD HEAT TREATMENT
195	UF- 53 TEST SPECIMENS UF- 54 TESTS AND RETESTS UF- 55 ULTRASONIC EXAMINATION MARKING AND REPORTS UF- 115 GENERAL PRESSURE RELIEF DEVICES UF- 125 GENERAL
196	PART UB REQUIREMENTS FOR PRESSURE VESSELS FABRICATED BY BRAZING GENERAL UB- 1 SCOPE UB- 2 ELEVATED TEMPERATURE UB- 3 SERVICE RESTRICTIONS MATERIALS UB- 5 GENERAL UB- 6 BRAZING FILLER METALS UB- 7 FLUXES AND ATMOSPHERES DESIGN UB- 9 GENERAL
197	UB- 10 STRENGTH OF BRAZED JOINTS UB- 11 QUALIFICATION OF BRAZED JOINTS FOR DESIGN TEMPERATURES UP TO THE MAXIMUM SHOWN IN COLUMN 1 OF TABLE UB- 2 UB- 12 QUALIFICATION OF BRAZED JOINTS FOR DESIGN TEMPERATURES IN THE RANGE SHOWN IN COLUMN 2 OF TABLE UB- 2 UB- 13 CORROSION UB- 14 JOINT EFFICIENCY FACTORS UB-2 MAXIMUM DESIGN TEMPERATURES FOR BRAZING FILLER METAL
198	UB- 15 APPLICATION OF BRAZING FILLER METAL UB- 16 PERMISSIBLE TYPES OF JOINTS UB- 17 JOINT CLEARANCE UB-14 EXAMPLES OF FILLER METAL APPLICATION
199	UB- 18 JOINT BRAZING PROCEDURE UB- 19 OPENINGS UB- 20 NOZZLES UB-16 SOME ACCEPTABLE TYPES OF BRAZED JOINTS UB-17 RECOMMENDED JOINT CLEARANCES AT BRAZING TEMPERATURE
200	UB- 21 BRAZED CONNECTIONS UB- 22 LOW TEMPERATURE OPERATION FABRICATION UB- 30 GENERAL UB- 31 QUALIFICATION OF BRAZING PROCEDURE UB- 32 QUALIFICATION OF BRAZERS AND BRAZING OPERATORS
201	UB- 33 BUTTSTRAPS UB- 34 CLEANING OF SURFACES TO BE BRAZED UB- 35 CLEARANCE BETWEEN SURFACES TO BE BRAZED UB- 36 POSTBRAZING OPERATIONS UB- 37 REPAIR OF DEFECTIVE BRAZING INSPECTION AND TESTS UB- 40 GENERAL UB- 41 INSPECTION DURING FABRICATION
202	UB- 42 PROCEDURE UB- 43 BRAZER AND BRAZING OPERATOR UB- 44 VISUAL EXAMINATION UB- 50 EXEMPTIONS MARKING AND REPORTS UB- 55 GENERAL PRESSURE RELIEF DEVICES UB- 60 GENERAL
203	SUBSECTION C REQUIREMENTS PERTAINING TO CLASSES OF MATERIALS PART UCS REQUIREMENTS FOR PRESSURE VESSELS CONSTRUCTED OF CARBON AND LOW ALLOY STEELS1 GENERAL UCS-1 SCOPE MATERIALS UCS- 5 GENERAL
204	UCS- 6 STEEL PLATES UCS- 7 STEEL FORGINGS UCS- 8 STEEL CASTINGS UCS- 9 STEEL PIPE AND TUBES UCS- 10 BOLT MATERIALS UCS- 11 NUTS AND WASHERS UCS- 12 BARS AND SHAPES
205	UCS-23 CARBON AND LOW ALLOY STEEL
206	DESIGN UCS- 16 GENERAL UCS- 19 WELDED JOINTS UCS- 23 MAXIMUM ALLOWABLE STRESS VALUES UCS- 27 SHELLS MADE FROM PIPE UCS- 28 THICKNESS OF SHELLS UNDER EXTERNAL PRESSURE UCS- 29 STIFFENING RINGS FOR SHELLS UNDER EXTERNAL PRESSURE UCS- 30 ATTACHMENT OF STIFFENING RINGS TO SHELL UCS- 33 FORMED HEADS, PRESSURE ON CONVEX SIDE UCS- 56 REQUIREMENTS FOR POSTWELD HEAT TREATMENT
208	UCS-56 POSTWELD HEAT TREATMENT REQUIREMENTS FOR CARBON AND LOW ALLOY STEELS
216	UCS- 57 RADIOGRAPHIC EXAMINATION LOW TEMPERATURE OPERATION UCS- 65 SCOPE UCS-56.1 ALTERNATIVE POSTWELD HEAT TREATMENT REQUIREMENTS FOR CARBON AND LOW ALLOY STEELS UCS-57 THICKNESS ABOVE WHICH FULL RADIOGRAPHIC EXAMINATION OF BUTT WELDED JOINTS IS MANDATORY
217	UCS- 66 MATERIALS
218	UCS-66 IMPACT TEST EXEMPTION CURVES
221	UCS-66M IMPACT TEST EXEMPTION CURVES
222	UCS- 67 IMPACT TESTS OF WELDING PROCEDURES
223	UCS-66 TABULAR VALUES FOR FIG. UCS-66 AND FIG. UCS-66M
225	UCS-66.1 REDUCTION IN MINIMUM DESIGN METAL TEMPERATURE WITHOUT IMPACT TESTING
226	UCS-66.1M REDUCTION IN MINIMUM DESIGN METAL TEMPERATURE WITHOUT IMPACT TESTING
227	UCS-66.2 DIAGRAM OF UCS-66 RULES FOR DETERMINING LOWEST MINIMUM DESIGN METAL TEMPERATURE (MDMT) WITHOUT IMPACT TESTING
228	UCS- 68 DESIGN4
229	UCS-66.3 SOME TYPICAL VESSEL DETAILS SHOWING THE GOVERNING THICKNESSES AS DEFINED IN UCS-66
232	FABRICATION UCS- 75 GENERAL UCS- 79 FORMING SHELL SECTIONS AND HEADS UCS- 85 HEAT TREATMENT OF TEST SPECIMENS
233	INSPECTION AND TESTS UCS- 90 GENERAL MARKING AND REPORTS UCS- 115 GENERAL PRESSURE RELIEF DEVICES UCS- 125 GENERAL NONMANDATORY APPENDIX CS UCS- 150 GENERAL UCS- 151 CREEP- RUPTURE PROPERTIES OF CARBON STEELS UCS- 160 VESSELS OPERATING AT TEMPERATURES COLDER THAN THE MDMT STAMPED ON THE NAMEPLATE
234	PART UNF REQUIREMENTS FOR PRESSURE VESSELS CONSTRUCTED OF NONFERROUS MATERIALS GENERAL UNF- 1 SCOPE UNF- 3 USES UNF- 4 CONDITIONS OF SERVICE MATERIALS UNF- 5 GENERAL UNF- 6 NONFERROUS PLATE UNF- 7 FORGINGS UNF- 8 CASTINGS UNF- 12 BOLT MATERIALS
235	UNF- 13 NUTS AND WASHERS UNF- 14 RODS, BARS, AND SHAPES UNF- 15 OTHER MATERIALS DESIGN UNF- 16 GENERAL UNF- 19 WELDED JOINTS UNF- 23 MAXIMUM ALLOWABLE STRESS VALUES
236	UNF-23.1 NONFERROUS METALS – ALUMINUM AND ALUMINUM ALLOY PRODUCTS UNF-23.2 NONFERROUS METALS – COPPER AND COPPER ALLOYS
237	UNF-23.3 NONFERROUS METALS – NICKEL, COBALT, AND HIGH NICKEL ALLOYS
238	UNF-23.4 NONFERROUS METALS – TITANIUM AND TITANIUM ALLOYS
239	UNF- 28 THICKNESS OF SHELLS UNDER EXTERNAL PRESSURE UNF- 30 STIFFENING RINGS UNF- 33 FORMED HEADS, PRESSURE ON CONVEX SIDE UNF- 56 POSTWELD HEAT TREATMENT UNF-23.5 NONFERROUS METALS – ZIRCONIUM
240	UNF- 57 RADIOGRAPHIC EXAMINATION UNF- 58 LIQUID PENETRANT EXAMINATION UNF- 65 LOW TEMPERATURE OPERATION FABRICATION UNF- 75 GENERAL
241	UNF- 77 FORMING SHELL SECTIONS AND HEADS UNF- 78 WELDING UNF- 79 REQUIREMENTS FOR POSTFABRICATION HEAT TREATMENT DUE TO STRAINING
242	INSPECTION AND TESTS UNF- 90 GENERAL UNF- 91 REQUIREMENTS FOR PENETRAMETER UNF- 95 WELDING TEST PLATES UNF-79 POSTFABRICATION STRAIN LIMITS AND REQUIRED HEAT TREATMENT
243	PART UNF FIGURE UNF-79 ILLUSTRATION OF COLD FORMING OPERATIONS FOR FLARING, SWAGING, AND UPSETTING OF TUBING
244	MARKING AND REPORTS UNF- 115 GENERAL PRESSURE RELIEF DEVICES UNF- 125 GENERAL VESSELS APPENDIX NF CHARACTERISTICS OF THE NONFERROUS MATERIALS ( INFORMATIVE AND NONMANDATORY) NF- 1 PURPOSE NF- 2 GENERAL NF- 3 PROPERTIES NF- 4 MAGNETIC PROPERTIES NF- 5 ELEVATED TEMPERATURE EFFECTS NF- 6 LOW TEMPERATURE BEHAVIOR NF- 7 THERMAL CUTTING NF- 8 MACHINING NF- 9 GAS WELDING
245	NF- 10 METAL ARC WELDING NF- 11 INERT GAS METAL ARC WELDING NF- 12 RESISTANCE WELDING NF- 13 CORROSION NF- 14 SPECIAL COMMENTS
246	PART UHA REQUIREMENTS FOR PRESSURE VESSELS CONSTRUCTED OF HIGH ALLOY STEEL GENERAL UHA- 1 SCOPE UHA- 5 USES UHA- 6 CONDITIONS OF SERVICE UHA- 8 MATERIAL MATERIALS UHA- 11 GENERAL UHA- 12 BOLT MATERIALS
247	UHA-23 HIGH ALLOY STEEL
249	UHA- 13 NUTS AND WASHERS DESIGN UHA- 20 GENERAL UHA- 21 WELDED JOINTS UHA- 23 MAXIMUM ALLOWABLE STRESS VALUES UHA- 28 THICKNESS OF SHELLS UNDER EXTERNAL PRESSURE UHA- 29 STIFFENING RINGS FOR SHELLS UNDER EXTERNAL PRESSURE UHA- 30 ATTACHMENT OF STIFFENING RINGS TO SHELL
250	UHA- 31 FORMED HEADS, PRESSURE ON CONVEX SIDE UHA- 32 REQUIREMENTS FOR POSTWELD HEAT TREATMENT UHA- 33 RADIOGRAPHIC EXAMINATION UHA- 34 LIQUID PENETRANT EXAMINATION FABRICATION UHA- 40 GENERAL UHA- 42 WELD METAL COMPOSITION
251	UHA-32 POSTWELD HEAT TREATMENT REQUIREMENTS FOR HIGH ALLOY STEELS
253	UHA- 44 REQUIREMENTS FOR POSTFABRICATION HEAT TREATMENT DUE TO STRAINING
254	INSPECTION AND TESTS UHA- 50 GENERAL UHA- 51 IMPACT TESTS
255	UHA-44 POSTFABRICATION STRAIN LIMITS AND REQUIRED HEAT TREATMENT
256	PART UHA FIGURE UHA-44 ILLUSTRATION OF COLD FORMING OPERATIONS FOR FLARING, SWAGING, AND UPSETTING OF TUBING
258	UHA- 52 WELDED TEST PLATES MARKING AND REPORTS UHA- 60 GENERAL PRESSURE RELIEF DEVICES UHA- 65 GENERAL APPENDIX HA SUGGESTIONS ON THE SELECTION AND TREATMENT OF AUSTENITIC CHROMIUM– NICKEL AND FERRITIC AND MARTENSITIC HIGH CHROMIUM STEELS ( INFORMATIVE AND NONMANDATORY) UHA- 100 GENERAL UHA- 101 STRUCTURE UHA- 102 INTERGRANULAR CORROSION UHA- 103 STRESS CORROSION CRACKING UHA- 104 SIGMA PHASE EMBRITTLEMENT UHA- 105 HEAT TREATMENT OF AUSTENITIC CHROMIUM– NICKEL STEELS UHA- 107 DISSIMILAR WELD METAL UHA- 108 FABRICATION
259	UHA- 109 885 ° F ( 475 ° C) EMBRITTLEMENT
260	PART UCI REQUIREMENTS FOR PRESSURE VESSELS CONSTRUCTED OF CAST IRON GENERAL UCI- 1 SCOPE UCI- 2 SERVICE RESTRICTIONS UCI- 3 PRESSURE– TEMPERATURE LIMITATIONS MATERIALS UCI- 5 GENERAL UCI- 12 BOLT MATERIALS DESIGN UCI- 16 GENERAL
261	UCI- 23 MAXIMUM ALLOWABLE STRESS VALUES UCI- 28 THICKNESS OF SHELLS UNDER EXTERNAL PRESSURE UCI- 29 DUAL METAL CYLINDERS UCI- 32 HEADS WITH PRESSURE ON CONCAVE SIDE UCI-23 MAXIMUM ALLOWABLE STRESS VALUES IN TENSION FOR CAST IRON
262	UCI- 33 HEADS WITH PRESSURE ON CONVEX SIDE UCI- 35 SPHERICALLY SHAPED COVERS ( HEADS) UCI- 36 OPENINGS AND REINFORCEMENTS UCI- 37 CORNERS AND FILLETS FABRICATION UCI- 75 GENERAL UCI- 78 REPAIRS IN CAST IRON MATERIALS UCI-78.1
263	INSPECTION AND TESTS UCI- 90 GENERAL UCI- 99 STANDARD HYDROSTATIC TEST UCI- 101 HYDROSTATIC TEST TO DESTRUCTION UCI-78.2
264	MARKING AND REPORTS UCI- 115 GENERAL PRESSURE RELIEF DEVICES UCI- 125 GENERAL
265	PART UCL REQUIREMENTS FOR WELDED PRESSURE VESSELS CONSTRUCTED OF MATERIAL WITH CORROSION RESISTANT INTEGRAL CLADDING, WELD METAL OVERLAY CLADDING, OR WITH APPLIED LININGS GENERAL UCL- 1 SCOPE UCL- 2 METHODS OF FABRICATION UCL- 3 CONDITIONS OF SERVICE MATERIALS UCL- 10 GENERAL UCL- 11 INTEGRAL AND WELD METAL OVERLAY CLAD MATERIAL
266	UCL- 12 LINING DESIGN UCL- 20 GENERAL UCL- 23 MAXIMUM ALLOWABLE STRESS VALUES
267	UCL- 24 MAXIMUM ALLOWABLE WORKING TEMPERATURE UCL- 25 CORROSION OF CLADDING OR LINING MATERIAL UCL- 26 THICKNESS OF SHELLS AND HEADS UNDER EXTERNAL PRESSURE UCL- 27 LOW TEMPERATURE OPERATIONS FABRICATION UCL- 30 GENERAL UCL- 31 JOINTS IN INTEGRAL OR WELD METAL OVERLAY CLADDING AND APPLIED LININGS UCL- 32 WELD METAL COMPOSITION
268	UCL- 33 INSERTED STRIPS IN CLAD MATERIAL UCL- 34 POSTWELD HEAT TREATMENT UCL- 35 RADIOGRAPHIC EXAMINATION UCL- 36 EXAMINATION OF CHROMIUM STAINLESS STEEL CLADDING OR LINING
269	UCL- 40 WELDING PROCEDURES UCL- 42 ALLOY WELDS IN BASE METAL UCL- 46 FILLET WELDS INSPECTION AND TESTS UCL- 50 GENERAL UCL- 51 TIGHTNESS OF APPLIED LINING UCL- 52 HYDROSTATIC TEST MARKING AND REPORTS UCL- 55 GENERAL PRESSURE RELIEF DEVICES UCL- 60 GENERAL
270	PART UCD REQUIREMENTS FOR PRESSURE VESSELS CONSTRUCTED OF CAST DUCTILE IRON GENERAL UCD- 1 SCOPE UCD- 2 SERVICE RESTRICTIONS UCD- 3 PRESSURE– TEMPERATURE LIMITATIONS MATERIALS UCD- 5 GENERAL UCD- 12 BOLT MATERIALS DESIGN UCD- 16 GENERAL
271	UCD- 23 MAXIMUM ALLOWABLE STRESS VALUES UCD- 28 THICKNESS OF SHELLS UNDER EXTERNAL PRESSURE UCD- 32 HEADS WITH PRESSURE ON CONCAVE SIDE UCD- 33 HEADS WITH PRESSURE ON CONVEX SIDE UCD- 35 SPHERICALLY SHAPED COVERS ( HEADS) UCD- 36 OPENINGS AND REINFORCEMENTS UCD- 37 CORNERS AND FILLETS UCD-23 MAXIMUM ALLOWABLE STRESS VALUES IN TENSION FOR CAST DUCTILE IRON, ksi (MPa)
272	FABRICATION UCD- 75 GENERAL UCD- 78 REPAIRS IN CAST DUCTILE IRON MATERIAL UCD-78.1 UCD-78.2
273	INSPECTION AND TESTS UCD- 90 GENERAL UCD- 99 STANDARD HYDROSTATIC TEST UCD- 101 HYDROSTATIC TEST TO DESTRUCTION MARKING AND REPORTS UCD- 115 GENERAL PRESSURE RELIEF DEVICES UCD- 125 GENERAL
274	PART UHT REQUIREMENTS FOR PRESSURE VESSELS CONSTRUCTED OF FERRITIC STEELS WITH TENSILE PROPERTIES ENHANCED BY HEAT TREATMENT GENERAL UHT- 1 SCOPE MATERIALS UHT- 5 GENERAL UHT- 6 TEST REQUIREMENTS
275	DESIGN UHT- 16 GENERAL UHT- 17 WELDED JOINTS UHT-6.1 CHARPY V-NOTCH IMPACT TEST REQUIREMENTS UHT-6.1M CHARPY V-NOTCH IMPACT TEST REQUIREMENTS
276	UHT- 18 NOZZLES UHT- 19 CONICAL SECTIONS UHT- 20 JOINT ALIGNMENT UHT- 23 MAXIMUM ALLOWABLE STRESS VALUES
277	UHT-18.1 ACCEPTABLE WELDED NOZZLE ATTACHMENT READILY RADIOGRAPHED TO CODE STANDARDS
278	UHT-18.2 ACCEPTABLE FULL PENETRATION WELDED NOZZLE ATTACHMENTS RADIOGRAPHABLE WITH DIFFICULTY AND GENERALLY REQUIRING SPECIAL TECHNIQUES INCLUDING MULTIPLE EXPOSURES TO TAKE CARE OF THICKNESS VARIATIONS
279	UHT- 25 CORROSION ALLOWANCE UHT- 27 THICKNESS OF SHELLS UNDER EXTERNAL PRESSURE UHT- 28 STRUCTURAL ATTACHMENTS AND STIFFENING RINGS UHT- 29 STIFFENING RINGS FOR SHELLS UNDER EXTERNAL PRESSURE UHT- 30 ATTACHMENT OF STIFFENING RINGS TO SHELLS UHT- 32 FORMED HEADS, PRESSURE ON CONCAVE SIDE UHT- 33 FORMED HEADS, PRESSURE ON CONVEX SIDE UHT-23 FERRITIC STEELS WITH PROPERTIES ENHANCED BY HEAT TREATMENT
280	UHT- 34 HEMISPHERICAL HEADS UHT- 40 MATERIALS HAVING DIFFERENT COEFFICIENTS OF EXPANSION UHT- 56 POSTWELD HEAT TREATMENT UHT- 57 EXAMINATION
281	UHT-56 POSTWELD HEAT TREATMENT REQUIREMENTS FOR MATERIALS IN TABLE UHT-23
282	FABRICATION UHT- 75 GENERAL UHT- 79 FORMING SHELL SECTIONS AND HEADS UHT- 80 HEAT TREATMENT UHT- 81 HEAT TREATMENT VERIFICATION TESTS
283	UHT- 82 WELDING
284	UHT- 83 METHODS OF METAL REMOVAL UHT- 84 WELD FINISH UHT- 85 STRUCTURAL AND TEMPORARY WELDS UHT- 86 MARKING ON PLATES AND OTHER MATERIALS INSPECTION AND TESTS UHT- 90 GENERAL MARKING AND REPORTS UHT- 115 GENERAL
285	PRESSURE RELIEF DEVICES UHT- 125 GENERAL
286	PART ULW REQUIREMENTS FOR PRESSURE VESSELS FABRICATED BY LAYERED CONSTRUCTION INTRODUCTION ULW- 1 SCOPE ULW- 2 NOMENCLATURE MATERIAL ULW- 5 GENERAL DESIGN ULW- 16 GENERAL
287	ULW-2.1 SOME ACCEPTABLE LAYERED SHELL TYPES
288	ULW-2.2 SOME ACCEPTABLE LAYERED HEAD TYPES
289	ULW- 17 DESIGN OF WELDED JOINTS
290	ULW-17.1 TRANSITIONS OF LAYERED SHELL SECTIONS
291	ULW-17.2 SOME ACCEPTABLE SOLID HEAD ATTACHMENTS TO LAYERED SHELL SECTIONS
293	ULW-17.3 SOME ACCEPTABLE FLAT HEADS AND TUBE SHEETS WITH HUBS JOINING LAYERED SHELL SECTIONS
294	ULW-17.4 SOME ACCEPTABLE FLANGES FOR LAYERED SHELLS
295	ULW-17.5 SOME ACCEPTABLE LAYERED HEAD ATTACHMENTS TO LAYERED SHELLS
296	ULW-17.6 SOME ACCEPTABLE WELDED JOINTS OF LAYERED-TO-LAYERED AND LAYERED-TO-SOLID SECTIONS
297	ULW- 18 NOZZLE ATTACHMENTS AND OPENING REINFORCEMENT ULW- 20 WELDED JOINT EFFICIENCY ULW- 22 ATTACHMENTS ULW- 26 POSTWELD HEAT TREATMENT
298	ULW-18.1 SOME ACCEPTABLE NOZZLE ATTACHMENTS IN LAYERED SHELL SECTIONS
300	ULW-22 SOME ACCEPTABLE SUPPORTS FOR LAYERED VESSELS
301	WELDING ULW- 31 WELDED JOINTS ULW- 32 WELDING PROCEDURE QUALIFICATION ULW- 33 PERFORMANCE QUALIFICATION NONDESTRUCTIVE EXAMINATION OF WELDED JOINTS ULW- 50 GENERAL ULW- 51 INNER SHELLS AND INNER HEADS ULW- 52 LAYERS — WELDED JOINTS
302	ULW-32.1 SOLID-TO-LAYERED AND LAYERED-TO-LAYERED TEST PLATES
303	ULW-32.2 ULW-32.3 ULW-32.4
304	ULW- 53 LAYERS — STEP WELDED GIRTH JOINTS ULW- 54 BUTT JOINTS ULW- 55 FLAT HEAD AND TUBESHEET WELD JOINTS ULW- 56 NOZZLE AND COMMUNICATING CHAMBERS WELD JOINTS
305	ULW- 57 RANDOM SPOT EXAMINATION AND REPAIRS OF WELD ULW-54.1
306	ULW-54.2
307	FABRICATION ULW- 75 GENERAL ULW- 76 VENT HOLES ULW- 77 CONTACT BETWEEN LAYERS ULW- 78 ALTERNATIVE TO MEASURING CONTACT BETWEEN LAYERS DURING CONSTRUCTION
308	INSPECTION AND TESTING ULW- 90 GENERAL MARKING AND REPORTS ULW- 115 GENERAL PRESSURE RELIEF DEVICES ULW- 125 GENERAL ULW-77
309	PART ULT ALTERNATIVE RULES FOR PRESSURE VESSELS CONSTRUCTED OF MATERIALS HAVING HIGHER ALLOWABLE STRESSES AT LOW TEMPERATURE GENERAL ULT- 1 SCOPE ULT- 2 CONDITIONS OF SERVICE ULT- 5 GENERAL
310	DESIGN ULT- 16 GENERAL ULT- 17 WELDED JOINTS ULT- 18 NOZZLES AND OTHER CONNECTIONS ULT- 23 MAXIMUM ALLOWABLE STRESS VALUES ULT- 27 THICKNESS OF SHELLS ULT- 28 THICKNESS OF SHELLS UNDER EXTERNAL PRESSURE ULT- 29 STIFFENING RINGS FOR SHELLS UNDER EXTERNAL PRESSURE ULT- 30 STRUCTURAL ATTACHMENTS
312	ULT-23 MAXIMUM ALLOWABLE STRESS VALUES IN TENSION FOR 5%, 8%, AND 9% NICKEL STEELS, TYPE 304 STAINLESS STEEL, AND 5083-O ALUMINUM ALLOY AT CRYOGENIC TEMPERATURES FOR WELDED AND NONWELDED CONSTRUCTION
315	ULT- 56 POSTWELD HEAT TREATMENT ULT- 57 EXAMINATION FABRICATION ULT- 75 GENERAL ULT- 79 FORMING SHELL SECTIONS AND HEADS ULT- 82 WELDING ULT- 86 MARKING ON PLATE AND OTHER MATERIALS INSPECTION AND TESTS ULT- 90 GENERAL ULT- 99 HYDROSTATIC TEST
316	ULT-82 MINIMUM TENSILE STRENGTH REQUIREMENTS FOR WELDING PROCEDURE QUALIFICATION TESTS ON TENSION SPECIMENS CONFORMING TO QW-462.1
318	ULT- 100 PNEUMATIC TEST MARKING AND REPORTS ULT- 115 GENERAL PART ULT FIGURE ULT-82 WELD METAL DELTA FERRITE CONTENT
319	PRESSURE RELIEF DEVICES ULT- 125 GENERAL
320	PART UHX RULES FOR SHELL- AND- TUBE HEAT EXCHANGERS UHX- 1 SCOPE UHX- 2 MATERIALS AND METHODS OF FABRICATION UHX- 3 TERMINOLOGY UHX- 4 DESIGN UHX- 9 TUBESHEET FLANGED EXTENSION
321	UHX-3 TERMINOLOGY OF HEAT EXCHANGER COMPONENTS
322	UHX- 10 GENERAL CONDITIONS OF APPLICABILITY FOR TUBESHEETS UHX- 11 TUBESHEET CHARACTERISTICS
323	UHX-9 SOME REPRESENTATIVE CONFIGURATIONS DESCRIBING THE MINIMUM REQUIRED THICKNESS OF THE TUBESHEET FLANGED EXTENSION, hr UHX-10 INTEGRAL CHANNELS
325	UHX-11.1 TUBESHEET GEOMETRY
326	UHX-11.2 TYPICAL UNTUBED LANE CONFIGURATIONS
327	UHX- 12 RULES FOR THE DESIGN OF U- TUBE TUBESHEETS
328	UHX-11.3 CURVES FOR THE DETERMINATION OF E/ E AND v (EQUILATERAL TRIANGULAR PATTERN)
329	UHX-11.4 CURVES FOR THE DETERMINATION OF E* /E AND v* (SQUARE PATTERN)
330	UHX-12.1 U-TUBE TUBESHEET CONFIGURATIONS
334	UHX- 13 RULES FOR THE DESIGN OF FIXED TUBESHEETS
335	UHX-13.1 FIXED TUBESHEET CONFIGURATIONS
339	UHX-13.1 FORMULAS FOR DETERMINATION OF Zd, Zv, Zm, AND Fm
340	UHX-13.2 Zd, Zv, and Zm VERSUS Xa
341	UHX-13.3-1 Fm VERSUS Xa (0.0 LESS THAN OR EQUAL TO Q3 LESS THAN OR EQUAL TO 0.8)
342	UHX-13.3-2 Fm VERSUS Xa (−0.8 LESS THAN OR EQUAL TO Q3 LESS THAN OR EQUAL TO 0.0)
344	UHX-13.4 SHELL WITH INCREASED THICKNESS ADJACENT TO THE TUBESHEETS
347	UHX- 14 RULES FOR THE DESIGN OF FLOATING TUBESHEETS
348	UHX-14.1 FLOATING TUBESHEET HEAT EXCHANGERS
349	UHX-14.2 STATIONARY TUBESHEET CONFIGURATIONS
350	UHX-14.3 FLOATING TUBESHEET CONFIGURATIONS
356	UHX- 15 TUBE- TO- TUBESHEET WELDS UHX- 16 THIN- WALLED EXPANSION JOINTS UHX- 17 THICK- WALLED EXPANSION JOINTS UHX- 18 PRESSURE TEST REQUIREMENTS UHX- 19 HEAT EXCHANGER MARKING AND REPORTS
357	UHX-17 THICK-WALLED EXPANSION JOINT LOAD CASES AND STRESS LIMITS
358	UHX- 20 EXAMPLES
374	MANDATORY APPENDICES 1 SUPPLEMENTARY DESIGN FORMULAS
394	2 RULES FOR BOLTED FLANGE CONNECTIONS WITH RING TYPE GASKETS
416	3 DEFINITIONS
419	4 ROUNDED INDICATIONS CHARTS ACCEPTANCE STANDARD FOR RADIOGRAPHICALLY DETERMINED ROUNDED INDICATIONS IN WELDS
428	5 FLANGED AND FLUED OR FLANGED ONLY EXPANSION JOINTS
431	6 METHODS FOR MAGNETIC PARTICLE EXAMINATION ( MT)
433	7 EXAMINATION OF STEEL CASTINGS
436	8 METHODS FOR LIQUID PENETRANT EXAMINATION ( PT)
438	9 JACKETED VESSELS
447	10 QUALITY CONTROL SYSTEM
450	11 CAPACITY CONVERSIONS FOR SAFETY VALVES
454	12 ULTRASONIC EXAMINATION OF WELDS ( UT)
455	13 VESSELS OF NONCIRCULAR CROSS SECTION
495	14 INTEGRAL FLAT HEADS WITH A LARGE, SINGLE, CIRCULAR, CENTRALLY LOCATED OPENING
502	16 SUBMITTAL OF TECHNICAL INQUIRIES TO THE BOILER AND PRESSURE VESSEL COMMITTEE
504	17 DIMPLED OR EMBOSSED ASSEMBLIES
514	18 ADHESIVE ATTACHMENT OF NAMEPLATES
515	19 ELECTRICALLY HEATED OR GAS FIRED JACKETED STEAM KETTLES
516	20 HUBS MACHINED FROM PLATE
517	21 JACKETED VESSELS CONSTRUCTED OF WORK- HARDENED NICKEL
518	22 INTEGRALLY FORGED VESSELS
520	23 EXTERNAL PRESSURE DESIGN OF COPPER, COPPER ALLOY, AND TITANIUM ALLOY CONDENSER AND HEAT EXCHANGER TUBES WITH INTEGRAL FINS
522	24 DESIGN RULES FOR CLAMP CONNECTIONS
528	25 ACCEPTANCE OF TESTING LABORATORIES AND AUTHORIZED OBSERVERS FOR CAPACITY CERTIFICATION OF PRESSURE RELIEF VALVES
530	26 PRESSURE VESSEL AND HEAT EXCHANGER EXPANSION JOINTS
556	27 ALTERNATIVE REQUIREMENTS FOR GLASS- LINED VESSELS
559	28 ALTERNATIVE CORNER WELD JOINT DETAIL FOR BOX HEADERS FOR AIR- COOLED HEAT EXCHANGERS
562	30 RULES FOR DRILLED HOLES NOT PENETRATING THROUGH VESSEL WALL
564	31 RULES FOR Cr– Mo STEELS WITH ADDITIONAL REQUIREMENTS FOR WELDING AND HEAT TREATMENT
567	32 LOCAL THIN AREAS IN CYLINDRICAL SHELLS AND IN SPHERICAL SEGMENTS OF SHELLS
570	33 STANDARD UNITS FOR USE IN EQUATIONS
571	34 REQUIREMENTS FOR USE OF HIGH SILICON STAINLESS STEELS FOR PRESSURE VESSELS
573	NONMANDATORY APPENDICES A BASIS FOR ESTABLISHING ALLOWABLE LOADS FOR TUBE- TO- TUBESHEET JOINTS
579	C SUGGESTED METHODS FOR OBTAINING THE OPERATING TEMPERATURE OF VESSEL WALLS IN SERVICE
580	D SUGGESTED GOOD PRACTICE REGARDING INTERNAL STRUCTURES
581	E SUGGESTED GOOD PRACTICE REGARDING CORROSION ALLOWANCE
582	F SUGGESTED GOOD PRACTICE REGARDING LININGS
583	G SUGGESTED GOOD PRACTICE REGARDING PIPING REACTIONS AND DESIGN OF SUPPORTS AND ATTACHMENTS
585	H GUIDANCE TO ACCOMMODATE LOADINGS PRODUCED BY DEFLAGRATION
587	K SECTIONING OF WELDED JOINTS
589	L EXAMPLES ILLUSTRATING THE APPLICATION OF CODE FORMULAS AND RULES
637	M INSTALLATION AND OPERATION
643	P BASIS FOR ESTABLISHING ALLOWABLE STRESS VALUES FOR UCI, UCD, AND ULT MATERIALS
644	R PREHEATING
646	S DESIGN CONSIDERATIONS FOR BOLTED FLANGE CONNECTIONS
648	T TEMPERATURE PROTECTION
649	W GUIDE FOR PREPARING MANUFACTURER’S DATA REPORTS
667	Y FLAT FACE FLANGES WITH METAL- TO- METAL CONTACT OUTSIDE THE BOLT CIRCLE
680	DD GUIDE TO INFORMATION APPEARING ON CERTIFICATE OF AUTHORIZATION ( SEE FIG. DD- 1)
683	EE HALF- PIPE JACKETS
688	FF GUIDE FOR THE DESIGN AND OPERATION OF QUICK-ACTUATING ( QUICK- OPENING) CLOSURES
691	GG GUIDANCE FOR THE USE OF U. S. CUSTOMARY AND SI UNITS IN THE ASME BOILER AND PRESSURE VESSEL CODE
694	HH TUBE EXPANDING PROCEDURES AND QUALIFICATION
704	JJ FLOWCHARTS ILLUSTRATING IMPACT TESTING REQUIREMENTS AND EXEMPTIONS FROM IMPACT TESTING BY THE RULES OF UHA- 51
711	INDEX
720	INTERPRETATIONS VOLUME 57 – SECTION VIII-1
736	NUMERICAL INDEX
756	SUBJECT INDEX

Additional information

Standard Title	ASME BPVC – VIII – 1 -2007 BPVC Section VIII-Rules for Construction of Pressure Vessels Division 1
Published Code	ASME
Publication Date	2007
Pages Count	778

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASME BPVC VIII 1 2007

PDF Catalog

Related products