ASME PTB 3 2022

$98.04

ASME PTB-3 – 2022 ASME Section VIII-Division 2 Example Problem Manual

Published By	Publication Date	Number of Pages
ASME	2022	540

Guaranteed Safe Checkout

Category: ASME

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASME B&PV Code, Section VIII, Division 2 contains mandatory requirements, specific prohibitions, and nonmandatory guidance for the design, materials, fabrication, examination, inspection, testing, and certification of pressure vessels and their associated pressure relief devices. The 2007 edition of the code has been re-written and reorganized and incorporates the latest technologies for pressure vessel design. Since this initial release, the code has undergone further development in all of its Parts, including refinement of its Part 4 Design-by-Rule (DBR) procedures and Part 5 Design-by-Analysis (DBA) methods. These modifications are captured in this PTB document.

PDF Catalog

PDF Pages	PDF Title
6	FOREWORD
10	ACKNOWLEDGEMENTS
12	TABLE OF CONTENTS
14	PART 1 1.1 Introduction 1.2 Scope 1.3 Definitions 1.4 Organization and Use
15	1.5 VII-S Vessel Classes 1.6 References
16	PART 2 2.1 General 2.2 Example Problem Format 2.3 Calculation Precision
18	PART 3 3.1 Commentary on Rules to Establish the Minimum Design Metal Temperature (MDMT)
20	3.2 Example E3.1 – Use of MDMT Exemptions Curves
22	3.3 Example E3.2 – Use of MDMT Exemption Curves with Stress Reuction
24	3.4 Example E
30	PART 4 4.1 General Requirements
38	4.2 Welded Joints
46	4.3 Internal Design Pressure
92	4.4 Shells Under External Pressure and Allowable Compressive Stresses
158	4.5 Shells Openings in Shells and Heads
178	4.6 Flat Heads
190	4.7 Spherically Dished Bolted Covers
218	4.8 Quick-Actuating (Quick Opening) Closures
220	4.9 Braced and Stayed Surfaces
224	4.10 Ligaments
226	4.11 Jacketed Vessels
232	4.12 NonCircular Vessels
248	4.13 Layered Vessels
256	4.14 Evaluation of Vessels Outside of Tolerance
272	4.15 Supports and Attachments
290	4.16 Flanged Joints
310	4.17 Clamped Connections
322	4.18 Tubesheets in Shell anf Tube Heat Exchangers
414	4.19 Bellows Expansion Joints
432	4.20 Design Rules for Flexible Shell Element Expansion Joints
434	4.21 Tube-To-Tubesheet Welds
448	PART 5 5.1 General Requirements 5.2 Protection Against Plastic Collapse
468	5.3 Protection Against Local Failure
474	5.4 Protection Against Collapse from Buckling
480	5.5 Protection Against Failure from Cyclic Loading
512	PART 6 6.1 Example E6.1 – Postweld Heat Treatment of a Pressure Vessel
516	6.2 Example E6.2 – Out-of-Roundness of a Cylindrical Forged Vessel
518	PART 7 7.1 Inspection and Examination Rules Commentary
519	7.2 General Commentary
528	7.3 Example E7.1-NDE Requirements: Vessel with One Examination Group Designation
532	7.4 Example E7.2 – NDE Requirements: Vessel with Two Examination Group Designations
534	PART 8 8.1 Example E8.1 – Determination of a Hydrostatic Test Pressure
538	8.2 Example E8.2 – Determination of a Pneumatic Test Pressure