ASTM-A29/A29M 2023

$37.38

A29/A29M-23 Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought

Published By	Publication Date	Number of Pages
ASTM	2023	17

Guaranteed Safe Checkout

Categories: 77.140.60 - Steel bars and rods, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM A29/A29M-23

Active Standard: Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought

ASTM A29/A29M

Scope

1.1 This specification2 covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to carbon and alloy steel bars under each of the following ASTM specifications (or under any other ASTM specification which invokes this specification or portions thereof):

1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named.

1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall used independently of the other, and values from the two systems shall not be combined.

1.4 For purposes of determining conformance to this specification and the various material specifications referenced in 1.1, dimensional values shall be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.

Note 1: Specification A29/A29M previously listed dimensional tolerances for cold-finished bars; these are now found in Specification A108.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

alloy steel bars; carbon steel bars; cold finished steel bars; general delivery requirements; hot wrought steel bars; steel bars;

ICS Code

ICS Number Code 77.140.60 (Steel bars and rods)

DOI: 10.1520/A0029_A0029M-23

Additional information

Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties	A675/A675M
Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements	A304
Hot-Rolled Alloy Steel Bars:
Steel Bars, Alloy, Hot-Rolled or Cold-Finished, Quenched and Tempered	A434/A434M
Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping Components	A696
Cold-Finished Carbon Steel Bars:
Steel Bars, Carbon, Hot-Wrought, Special Quality	A576
Cold-Finished Alloy Steel Bars:
Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered	A434/A434M
Carbon and Alloy Steel Bars for Springs	A689
Steel Bars, Carbon, Quenched and Tempered	A321
Title of Specification	ASTM DesignationA
Hot-Rolled Carbon Steel Bars:
Cold-Drawn Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements	A311/A311M
Steel Bars, Carbon, Merchant Quality, Mechanical Properties	A663/A663M
Steel Bar, Carbon and Alloy, Cold-Finished	A108
Steel Bars and Shapes, Carbon Rolled from “T'' Rails	A499
Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both	A739
Steel Bars, Alloy, Standard Grades	A322
Steel Bars, Carbon, Merchant Quality, M-Grades	A575

ICS Codes	77.140.60 - Steel bars and rods