šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
ASTM-A341:2005 Edition

ASTM-A341:2005 Edition

$44.96

A341/A341M-00(2005) Standard Test Method for Direct Current Magnetic Properties of Materials Using D-C Permeameters and the Ballistic Test Methods

Published By Publication Date Number of Pages
ASTM 2005 12
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

1.1 This test method provides dc permeameter tests for the basic magnetic properties of materials in the form of bars, rods, wire, or strip specimens which may be cut, machined, or ground from cast, compacted, sintered, forged, extruded, rolled, or other fabricated materials. It includes tests for determination of the normal induction under symmetrically cyclically magnetized (SCM) conditions and the hysteresis loop (B-H loop) taken under conditions of rapidly changing or steep wavefront reversals of the direct current magnetic field strength.

1.2 This test method shall be used in conjunction with Practice A 34/A 34M.

1.3 This test method covers a range of magnetic field strength in the specimen from about 0.05 Oe [4 A/m] up to above 5000 Oe [400 kA/M] through the use of several permeameters. The separate permeameters cover this test region in several overlapping ranges.

1.4 Normal induction and hysteresis properties may be determined over the flux density range from essentially zero to intrinsic saturation for most materials.

1.5 Recommendations of the useful magnetic field strength range for each of the permeameters are shown in . Also, see Sections 3 and 4 for general limitations relative to the use of permeameters.

1.6 The symbols and abbreviated definitions used in this test method appear with and in appropriate sections of this document. For the official definitions, see Terminology A 340. Note that the term flux density used in this document is synonymous with the term magnetic induction.

1.7 The values and equations stated in customary cgs-emu and inch-pound or SI units are to be regarded separately as standard. Within this standard, SI units are shown in brackets except for the sections concerning calculations where there are separate sections for the respective unit systems. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages PDF Title
1 Scope
Referenced Documents
Significance and Use
2 Interferences
Apparatus
TABLE 1
FIG. 1
3 Test Specimens
TABLE 2
4 Calibration
Procedure
5 Calculation (Modified cgs Units)
Calculation (SI Units)
Report
6 Precision and Bias
Keywords
TABLE 3
7 A1. SPECIAL TEST REQUIREMENTS FOR EVALUATION OF MATERIALS IN GENERATOR ROTOR FORGINGS (CUSTOMARY UNITS)
A1.1 Scope
A1.2 Test Specimens (Customary Units)
A1.3 Procedure
A1.4 Accuracy
A1.5 Report
A2. CALIBRATION OF BALLISTIC GALVANOMETER (CUSTOMARY UNITS)
A2.1
A2.2
A2.3
8 X1. MUTUAL INDUCTOR CONSTRUCTION
X1.1
X2. AIR-FLUX COMPENSATION FOR B-SENSING COIL (CUSTOMARY UNITS)
X2.1 Air-Flux Correction and Automatic Compensation
9 X2.2
X3. HYSTERESIS LOSS AND ENERGY PRODUCT CALCULATION (CUSTOMARY UNITS)
X3.1
X3.2
FIG. X3.1
10 X4. EXTRAPOLATION OF MAGNETIC FIELD STRENGTH FROM H COIL POSITION TO TEST SPECIMEN SURFACE
X4.1
X4.2
X4.3
X4.4
X5. USE OF FLIP H COILS OR HALL-EFFECT DEVICES FOR MEASUREMENT OF MAGNETIC FIELD STRENGTH IN PERMEAMETERS
X5.1 Scope
FIG. X3.2
11 X5.2 Summary
X5.3 Flip H Coil
X5.4 Hall-Effect or Other Point-Field Measuring Devices
X6. ARC SUPPRESSION FOR DIRECTLY SWITCHED TEST UNITS
X6.1
X6.2
X6.3
X6.4
X6.5
12 REFERENCES
FIG. X6.1

Related products

ASTM-A341
$44.96