ASTM-A568 2005

$58.50

A568/A568M-05 Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

Published By	Publication Date	Number of Pages
ASTM	2005	26

Guaranteed Safe Checkout

Categories: 77.140.50 - Flat steel products and semi-products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M.

1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M).

1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.

1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.

1.5 lists permissible variations in dimensions and mass (see Note 0) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the ‘M’ specification is used. The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass .

1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable ‘M’ specification designation (SI units), the material shall be furnished to inch-pound units.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology
3	Materials and Manufacture Chemical Composition TABLE 1
4	Mechanical Properties General Requirements for Delivery TABLE 2
5	Dimensions, Tolerances, and Allowances Finish and Condition TABLE 3
6	Workmanship TABLE 4 TABLE 5
7	TABLE 6 TABLE 7
8	Retests and Disposition of Non-Conforming Material TABLE 8 TABLE 9 TABLE 10 TABLE 11 TABLE 12
9	Inspection TABLE 13 TABLE 14 TABLE 15 TABLE 16
10	Rejection and Rehearing TABLE 17 TABLE 18 TABLE 19
11	Test Reports and Certification TABLE 20 TABLE 21 TABLE 22 TABLE 23 TABLE 24 TABLE 25
12	Product Marking Packing and Package Marking Keywords A1. PERMISSIBLE VARIATIONS IN DIMENSIONS AND MASS IN SI UNITS A1.1
13	TABLE A1.1 TABLE A1.2 TABLE A1.3
14	TABLE A1.4 TABLE A1.5 TABLE A1.6 TABLE A1.7 TABLE A1.8 TABLE A1.9
15	TABLE A1.10 TABLE A1.11 TABLE A1.12 TABLE A1.13
16	TABLE A1.14 TABLE A1.15 TABLE A1.16 TABLE A1.17
17	TABLE A1.18 TABLE A1.19 TABLE A1.20
18	X1. AGING EFFECTS ON FORMABILITY OF COLD-ROLLED CARBON-STEEL SHEET PRODUCTS X1.1 X1.2 X1.3 Low-Carbon Steels X1.4 Interstitial-Free Steels X1.5 Bake-Hardenable Steels
19	X2. STANDARD CHEMICAL RANGES AND LIMITS X2.1 TABLE X2.1
20	X3. PROCEDURE FOR DETERMINING BREAKAGE ALLOWANCE LEVELS (APPLICABLE TO CARBON STEEL SHEET ONLY) X3.1 X3.2 X3.3 X3.4 TABLE X2.2
21	X4. PROCEDURES FOR DETERMINING THE EXTENT OF PLASTIC DEFORMATION ENCOUNTERED IN FORMING OR DRAWING X4.1 Introduction X4.2 Circle Grid Method FIG. X4.1
22	X4.3 Procedure X4.4 Measurement of Strain After Forming X4.5 Evaluation of Strain Measurements FIG. X4.2
23	X4.6 Example of Major and Minor Strain Distribution X4.7 Example for Reducing Splitting Tendency FIG. X4.3 FIG. X4.4
24	X4.8 Scribed Square Method X4.9 Thickness Method X5. ALTERNATIVE METHODS FOR EXPRESSING FLATNESS X5.1 Introduction and Definitions X5.2 FIG. X5.1
25	TABLE X5.1 TABLE X5.2

Additional information

Standard Title	A568/A568M-05 Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Published Code	ASTM
Publication Date	2005
Pages Count	26
ICS Codes	77.140.50 - Flat steel products and semi-products

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-A568 2005

PDF Catalog

Related products