ASTM-A888 2020

$63.38

A888-20 Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

Published By	Publication Date	Number of Pages
ASTM	2020	59

Guaranteed Safe Checkout

Categories: 23.040.01 - Pipeline components and pipelines in general, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

ASTM A888-20

Historical Standard: Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

ASTM A888

Scope

1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.

1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the dimensions found in Tables 1 and 2 and all other applicable requirements given in this specification.2

1.3.1 Lengths:

1.3.2 Fittings:

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301.

Note 1: The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

cast iron; hubless pipe and fittings; no-hub pipe and fittings; soil pipe;

ICS Code

ICS Number Code 23.040.01 (Pipeline components in general. Pipelines)

DOI: 10.1520/A0888-20

Quarter Bend, Reducing	Fig. 6
Quarter Bend	Fig. 5
Sanitary Cross, Tapped	Fig. 38
Fifth Bend	Fig. 15
Y Branch	Fig. 28
Upright Y Wide Center Florida Special	Fig. 31
Vented Tub Wye Extended, Double	Fig. 62
Iron Body Cleanout, Tapped	Fig. 45
P Trap, Deep Seal	Fig. 48
Vented Tub Wye	Fig. 64
Y Branch, Upright	Fig. 30
Long Sweep, Reducing	Fig. 14
P Trap, Long	Fig. 47
Quarter Bend, with Side Opening	Fig. 7
Quarter Bend, with Heel Opening	Fig. 8
Closet Flange Riser	Fig. 57
Test Tee	Fig. 39
Tapped Extension Piece	Fig. 40
Sanitary Tapped Tee, Double Vertical	Fig. 27
Eighth Bend, Long	Fig. 18
Tapped Inlet, Double	Fig. 51
Twin Cleanout	Fig. 55
P Trap	Fig. 46
Quarter Bend, Tapped	Fig. 9
Sanitary Tee with Side Opening	Fig. 21
Sanitary Special Tee Tapped	Fig. 25
Quarter Bend, Long	Fig. 11
Y Branch, Combination 1/8 Bend Double	Fig. 33
Double Two-Way Cleanout	Fig. 65
Two-Way Cleanout	Fig. 54
Increaser-Reducer	Fig. 41
Sanitary Tee, New Orleans Special with Side Opening	Fig. 23
Sanitary Tee with 2 in. Side Opening R or L/R and L	Fig. 22
Eighth Bend	Fig. 17
Sanitary Cross with Side Opening	Fig. 35
Y Branch, Combination 1/8 Bend	Fig. 32
Modified Combination Wye and 1/8 Bend, Double, Extended	Fig. 53
P Trap with Tapped or Hubless Side Inlet	Fig. 61
Y Branch, Double	Fig. 29
Sanitary Cross, New Orleans, with Side Openings	Fig. 36
Running Trap with Double Vents	Fig. 60
10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 11/2 , 2, 3, 4, 5, 6, 8, 10, 12, and 15 in.	Fig. 1, Fig. 2
Long Sweep	Fig. 13
Tapped Adapter	Fig. 43
Sanitary Tapped Tee, Horizontal Twin	Fig. 26
Vented Tub Wye Extended Offset, Left or Right	Fig. 63
Increaser-Reducer, Short	Fig. 42
Closet Bend, Regular and Reducing	Fig. 56
Method of Specifying Fittings	Fig. 3
Tapping Bosses	Fig. 58
	Figures
Double Sweep Sanitary Tee (Extended)	Fig. 59
Short Sweep	Fig. 12
Quarter Bend, Double	Fig. 10
Sanitary Tee with 45° Side Openings and New Orleans	Fig. 24
P Trap, with Primer	Fig. 49
Sanitary Cross	Fig. 34
EDP/ASA Identification Numbers for Hubless Pipe	Fig. 1
Modified Combination Wye and 1/8 Bend, Double	Fig. 52
Blind Plug	Fig. 44
Sixteenth Bend	Fig. 19
P Trap, with Tapped Inlet	Fig. 50
Sixth Bend	Fig. 16
Sanitary Tee	Fig. 20
Sanitary Cross, New Orleans, with 45° Special and Regular Side Openings	Fig. 37
ICS Codes	23.040.01 - Pipeline components and pipelines in general


PDF Format	Searchable	Printable	Preview Now

ASTM-A888 2020

ASTM A888-20

Historical Standard: Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

ASTM A888

Related products

ASTM-A888 2020(Redline)