🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-D2513:2007 Edition

ASTM-D2513:2007 Edition

$58.50

D2513-07 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings

Published By Publication Date Number of Pages
ASTM 2007 27
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: , ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

1.1 This specification covers requirements and test methods for material (see Appendix X1) dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of plastic pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The annexes provide specific requirements and test methods for each of the materials currently approved. If and when additional materials are available, specific annex requirements will be added. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are covered in Annex A1.

1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A3 and Annex A4.

1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

1.4 The following is an index of the annexes and appendixes in this specification:

The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages PDF Title
1 Scope
Referenced Documents
2 Terminology
Materials
Requirements
3 TABLE 1
TABLE 2
4 TABLE 3
5 TABLE 4
6 Test Methods
7 Marking
8 Quality Assurance
9 A1. SUPPLEMENTAL REQUIREMENTS FOR GAS PRESSURE PIPE AND FITTINGS PRODUCED FROM POLYETHYLENE (PE) MATERIAL
A1.1 Scope
A1.2 Referenced Documents
A1.3 Materials
TABLE A1.1
TABLE A1.2
10 A1.4 Fittings
A1.5 Requirements for Pipe and Fittings
TABLE A1.3
11 TABLE A1.4
TABLE A1.5
12 A1.6 Marking
A2. SUPPLEMENTAL REQUIREMENTS FOR GAS PRESSURE PIPE AND FITTINGS PRODUCED FROM POLY (VINYL CHLORIDE) (PVC) COMPOUNDS FOR MAINTENANCE OR REPAIR
A2.1 Scope
A2.2 Referenced Documents
A2.3 Materials
A2.4 Requirements
13 A2.5 Safety Requirements
TABLE A2.1
TABLE A2.2
14 A3. IN-PLANT QUALITY CONTROL PROGRAM FOR PLASTIC PIPE AND FITTINGS UP TO AND INCLUDING 12 IN. NOMINAL DIAMETER
A3.1 Quality Control
A3.2 Pipe Tests
TABLE A2.3
TABLE A3.1
TABLE A3.2
15 A3.3 Fittings Tests9
FIG. A3.1
16 A4. IN-PLANT QUALITY CONTROL PROGRAM FOR 14-IN. AND LARGER DIAMETER POLYETHYLENE PIPE
A4.1
A4.2
A4.3
A5. SUPPLEMENTAL REQUIREMENTS FOR GAS PRESSURE PIPE AND FITTINGS PRODUCED FROM POLYAMIDE MATERIAL
A5.1 Scope
A5.2 Referenced Documents
A5.3 Materials
A5.4 Requirements for Pipe and Fittings
TABLE A5.1
TABLE A5.2
17 A5.5 Marking
A6. SUPPLEMENTAL REQUIREMENTS FOR GAS PRESSURE PIPE PRODUCED FROM MAGNETIC-DETECTABLE POLYETHYLENE MATERIAL (MDPEMAG/HDPEMAG) WITH UP TO 24 % CONCENTRATION (WEIGHT PERCENT) OF STRONTIUM FERRITE (SrFe)
A6.1 Scope
A6.2 Referenced Documents
TABLE A5.3
18 A6.3 Materials
A6.4 Fittings
A6.5 Requirements
TABLE A6.1
19 A6.6 Marking
A6.7 Quality Control
20 A7. SUPPLEMENTAL REQUIREMENTS FOR GAS PRESSURE PIPE PRODUCED FROM CROSSLINKED POLYETHYLENE (PEX) MATERIAL
A7.1 Scope
A7.2 Referenced Documents
A7.3 Materials
A7.4 Requirements for Pipe
21 A7.5 Marking
X1. NEW MATERIALS
X2. DESIGN CONSIDERATIONS
X2.1 General
X2.2 Design Equations
22 X2.3 Design Stress and Internal Pressure for Natural Gas
X2.4 Thermal Stress
23 X2.5 Installation Procedure
X2.6 Repair Considerations
X2.7 Environmental Effects
25 X3. GAS PRESSURE PIPE AND FITTINGS PRODUCED FROM POLYETHYLENE (PE) MATERIALS WITH MINIMUM REQUIRED STRENGTH (MRS) DESIGNATION
X3.1 Scope
X3.2 Referenced Documents
X3.3 Terminology
X3.4 Materials
X3.5 Requirements
TABLE X3.1
26 X3.6 Marking
REFERENCES
TABLE X3.2
TABLE X3.3

Related products

ASTM-D2513
$58.50