ASTM-D3410:2008 Edition

$44.96

D3410/D3410M-03(2008) Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading

Published By	Publication Date	Number of Pages
ASTM	2008	16

Guaranteed Safe Checkout

Categories: 83.140.20 - Laminated sheets, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D3410/D3410M-03-Reapproved2008

Historical Standard: Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading

ASTM D3410/D3410M

Scope

1.1 This test method determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers. The composite material forms are limited to continuous-fiber or discontinuous-fiber reinforced composites for which the elastic properties are specially orthotropic with respect to the test direction. This test procedure introduces the compressive force into the specimen through shear at wedge grip interfaces. This type of force transfer differs from the procedure in Test Method D 695 where compressive force is transmitted into the specimen by end-loading, Test Method D 6641/D 6641M where compressive force is transmitted by combined shear and end loading, and Test Method D 5467/D 5467M where compressive force is transmitted by subjecting a honeycomb core sandwich beam with thin skins to four-point bending.

1.2 This test method is applicable to composites made from unidirectional tape, wet-tow placement, textile (for example, fabric), short fibers, or similar product forms. Some product forms may require deviations from the test method.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pounds units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

Note 1—Additional procedures for determining compressive properties of resin-matrix composites may be found in Test Methods D 695, D 5467/D 5467M, and D 6641/D 6641M.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

composite materials; compressive modulus of elasticity; compressive properties; compressive strength; Poisson’s ratio; Composites; Compression testing–aerospace materials; Compression testing–composites; Compressive modulus of elasticity; High modulus fibrous composites; Modulus of elasticity; Poisson’s ratio; Polymers (composites); Resins (composite); Shear load; Shear testing–aerospace materials; Unsupported gage section

ICS Code

ICS Number Code 83.140.20 (Laminated sheets)

DOI: 10.1520/D3410_D3410M-03R08

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology Summary of Test Method
3	Significance and Use Interferences FIG. 1
4	FIG. 2
5	Apparatus FIG. 3
6	FIG. 4
7	FIG. 5 FIG. 6 FIG. 7 FIG. 8
8	Sampling and Test Specimens
9	TABLE 1
10	TABLE 2 TABLE 3
11	Calibration Conditioning Procedure
12	TABLE 4
13	FIG. 9
14	Calculation
15	Report FIG. 10
16	Precision and Bias Keywords REFERENCES

Additional information

Standard Title	D3410/D3410M-03(2008) Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
Published Code	ASTM
Publication Date	2008
Pages Count	16
ICS Codes	83.140.20 - Laminated sheets