ASTM-D5967 2004

$44.96

D5967-04 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

Published By	Publication Date	Number of Pages
ASTM	2004	19

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D5967-04

Historical Standard: Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

ASTM D5967

Scope

1.1 This test method is commonly referred to as the Mack T-8. This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading).

1.2 This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.

1.3 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are generally shown in parentheses when combined with SI units, and vice versa.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.

1.5 A Table of Contents follows:

Keywords

diesel engine oil; lubricants; soot; T-8 diesel engine; viscosity

ICS Code

ICS Number Code 75.100 (Lubricants, industrial oils and related products)

DOI: 10.1520/D5967-04

PDF Catalog

PDF Pages	PDF Title
1	Scope
2	Terminology
3	TABLE 1
4	Engine Fluids Preparation of Apparatus at Rebuild
5	Laboratory and Engine Test Stand Calibration/Non-Reference Requirements
7	TABLE 2 TABLE 3
9	Inspection of Fuel and Oil During Test TABLE 4
10	Keywords A1. REPORT FORMS A1.1 A2. SENSOR LOCATIONS A2.1 FIG. A2.1 FIG. A2.2
11	FIG. A2.3 FIG. A2.4 FIG. A2.5 FIG. A2.6
12	FIG. A2.7 FIG. A2.8
13	FIG. A2.9 FIG. A2.10
14	A3. KINEMATIC VISCOSITY AT 100°C FOR TEST METHOD D 5967 SAMPLES A3.1 A3.2 FIG. A2.11 FIG. A3.1
15	A3.3 FIG. A3.2 FIG. A3.3 FIG. A3.4
16	A4. ENHANCED THERMAL GRAVIMETRIC ANALYSIS (TGA) PROCEDURE A4.1 A4.2 A4.3 A4.4 A4.5
17	A5. PROCUREMENT OF TEST MATERIALS A5.1 A5.2 A5.3 A5.4 A5.5 A5.6 A6. SAFETY PRECAUTIONS A6.1 TABLE A5.1 TABLE A5.2
18	A7. DATA DICTIONARY A7.1 A8. T8-E EXTENDED LENGTH TEST REQUIREMENTS A8.3 Procedure TABLE A8.1
19	A9. T8-A ABBREVIATED LENGTH TEST REQUIREMENTS A9.1 A9.2 A9.3 TABLE A8.2 TABLE A9.1

Additional information

The Test Engine	6.2
Precision and Bias	13
Air Supply and Filtration	6.2.7
Plots of Operational Data	12.4
T-8E Extended Length Test Requirements	Annex A8
Failing Calibration Tests	9.7
Test Cycle	10.4
Terminology	3
Electronic Transmission of Test Results	12.3
Oil Consumption Calculations	10.7
Cylinder Liner, Piston, and Piston Ring Assembly	8.3
Periodic Measurements	10.9
Engine Oil System	6.2.3
Auxiliary Oil System	6.2.4
Bias	13.2
Keywords	14
Procurement of Test Materials	Annex A5
Data Dictionary	Annex A7
Calibration Frequency	9.1
Calibration Reference Oils	9.2
Scope	1
Report Forms	Annex A1
Blowby	10.10
Cleaning of Parts	8.1
Oil Samples	10.6
Engine Fluids	7
Reporting Test Results	12.1
Sensor Locations	Annex A2
Fuel Samples	10.8
Engine Shutdown	10.3
Report	12
Measurements	8.6
Valves, Seats, Guides, and Springs	8.2
Cleaning Materials	7.4
T-8A Abbreviated Length Test Requirements	Annex A9
Mack Test Engine	6.2.1
Post Test	10.13
Blowby Meter	6.2.6
Oil Consumption	11.3
Centrifugal Oil Filter Mass Gain	10.11
Calibration Test Acceptance	9.6
Assembly Instructions	8.5
Apparatus	6
Procedure	10
Deviations from Test Operational Limits	12.2
Fuel Inspections	11.2
Safety Precautions	Annex A6
New Laboratories and New Test Stands	9.4
Engine Cooling System	6.2.2
Test Fuel	7.2
Annexes
Inspection of Fuel and Oil During Test	11
Injectors and Injection Pump	8.4
Engine Start-Up	10.2
Intake Manifold Temperature Control	6.2.9
Crankcase Aspiration	6.2.5
General Description	6.1
Test Numbering	9.3
Precision	13.1
Laboratory and Engine Test Stand Calibration/Non-Reference Requirements	9
Test Oils	7.1
Oil Filter ∇P Calculation	10.12
Oil Addition/Drain	10.5
Non-Reference Oil Test Requirements	9.8
Kinematic Viscosity At 100°C For Test Method D 5967 Samples	Annex A3
Enhanced Thermal Gravimetric Analysis (TGA) Procedure	Annex A4
Fuel Supply	6.2.8
Pretest Procedure	10.1
Calibrated Laboratories and Test Stands	9.5
Summary of Test Methods	4
Oil Inspection	11.1
Significance and Use	5
Preparation of Apparatus at Rebuild	8
Referenced Documents	2
Engine Coolant	7.3