ASTM-D6080 2012(Redline)

$26.65

D6080-12 Standard Practice for Defining the Viscosity Characteristics of Hydraulic Fluids (Redline)

Published By	Publication Date	Number of Pages
ASTM	2012	8

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Significance and Use

5. Significance and Use

5.1 The purpose of this practice is to establish viscosity designations derived from viscosities measured by test methods which have a meaningful relationship to hydraulic fluid performance. This permits lubricant suppliers, lubricant users, and equipment designers to have a uniform and common basis for designating, specifying, or selecting the viscosity characteristics of hydraulic fluids.

5.2 This practice is not intended to be a replacement for Classification D2422 . Rather, it is an enhancement intended to provide a better description of the viscosity characteristics of lubricants used as hydraulic fluids.

5.3 This practice implies no evaluation of hydraulic oil quality other than its viscosity and shear stability under the conditions specified.

5.4 While it is not intended for other functional fluids, this practice may be useful in high-shear-stress applications where viscosity index (VI) improvers are used to extend the useful operating temperature range of the fluid.

5.5 This practice does not apply to other lubricants for which viscosity classification systems already exist, for example, SAE J300 for automotive engine oils and SAE J306 for axle and manual transmission lubricants.

1. Scope

1.1 This practice covers all hydraulic fluids based either on petroleum, synthetic, or naturally-occurring base stocks. It is not intended for water-containing hydraulic fluids.

1.2 For determination of viscosities at low temperature, this practice uses millipascal??second (mPa??s) as the unit of viscosity. For reference, 1 mPa??s is equivalent to 1 centipoise (cP). For determination of viscosities at high temperature, this practice uses millimetre squared per second (mm ² /s) as the unit of kinematic viscosity. For reference, 1 mm ² /s is equivalent to 1 centistoke (cSt).

1.3 This practice is applicable to fluids ranging in kinematic viscosity from about 4 to 150 mm ² /s as measured at a reference temperature of 40??C and to temperatures from ???50 to +16??C for a fluid viscosity of 750 mPa??s.

Note 1 ??? Fluids of lesser or greater viscosity than the range described in 1.3 are seldom used as hydraulic fluids. Any mathematical extrapolation of the system to either higher or lower viscosity grades may not be appropriate. Any need to expand the system should be evaluated on its own merit.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) D2270 Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 and 100C D2422 Classification of Industrial Fluid Lubricants by Viscosity System D2983 Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer D5621 Test Method for Sonic Shear Stability of Hydraulic Fluids E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

Society of Automotive Engineers (SAE) Standards

J306 Axle and Manual Transmission Lubricant Viscosity Classification

Keywords

Brookfield viscosity; hydraulic fluid; shear stability; viscosity; viscosity classification;

ICS Code

ICS Number Code 75.120 (Hydraulic fluids)

DOI: 10.1520/D6080-12 ASTM International is a member of CrossRef.

ASTM D6080 (Petroleum Standards)

Citing ASTM Standards

[Back to Top]

Additional information

Standard Title	D6080-12 Standard Practice for Defining the Viscosity Characteristics of Hydraulic Fluids (Redline)
Published Code	ASTM
Publication Date	2012
Pages Count	8

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-D6080 2012(Redline)

ASTM D6080 (Petroleum Standards)

Related products