ASTM-D7467 2010(Redline)

1.1 This specification covers fuel blend grades of 6 to 20 volume percent (%) biodiesel with the remainder being a light middle or middle distillate diesel fuel, collectively designated as B6 to B20. These grades are suitable for various types of diesel engines.

1.1.1 The biodiesel component of the blend shall conform to the requirements of Specification D6751 . The remainder of the fuel shall be a light middle or middle distillate grade diesel fuel conforming to Specification D975 grades No. 1-D and No. 2-D of any sulfur level specified with the following exceptions. The light middle or middle distillate grade diesel fuel whose sulfur level, aromatic level, cetane, or lubricity falls outside of Specification D975 may be blended with biodiesel meeting Specification D6751 , provided the finished mixtures meets this specification.

1.1.2 The fuel sulfur grades are described as follows:

1.1.2.1 Grade B6 to B20 S15 — A fuel with a maximum of 15 ppm sulfur.

1.1.2.2 Grade B6 to B20 S500 — A fuel with a maximum of 500 ppm sulfur.

1.1.2.3 Grade B6 to B20 S5000 — A fuel with a maximum of 5000 ppm sulfur.

1.2 This specification prescribes the required properties of B6 to B20 biodiesel blends at the time and place of delivery. The specification requirements may be applied at other points in the production and distribution system when provided by agreement between the purchaser and the supplier.

1.2.1 Nothing in this specification shall preclude observance of federal, state, or local regulations that may be more restrictive.

Note 1—The generation and dissipation of static electricity can create problems in the handling of distillate diesel fuel oils. For more information on this subject, see Guide D4865 .

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D56 Test Method for Flash Point by Tag Closed Cup Tester D86 Test Method for Distillation of Petroleum Products at Atmospheric Pressure D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester D129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method) D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) D482 Test Method for Ash from Petroleum Products D524 Test Method for Ramsbottom Carbon Residue of Petroleum Products D613 Test Method for Cetane Number of Diesel Fuel Oil D664 Test Method for Acid Number of Petroleum Products by Potentiometric Titration D975 Specification for Diesel Fuel Oils D976 Test Method for Calculated Cetane Index of Distillate Fuels D1266 Test Method for Sulfur in Petroleum Products (Lamp Method) D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption D1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method) D2500 Test Method for Cloud Point of Petroleum Products D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry D2709 Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge D2880 Specification for Gas Turbine Fuel Oils D3117 Test Method for Wax Appearance Point of Distillate Fuels D3120 Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester D4057 Practice for Manual Sampling of Petroleum and Petroleum Products D4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry D4539 Test Method for Filterability of Diesel Fuels by Low-Temperature Flow Test (LTFT) D4737 Test Method for Calculated Cetane Index by Four Variable Equation D4865 Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems D5453 Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence D5771 Test Method for Cloud Point of Petroleum Products (Optical Detection Stepped Cooling Method) D5772 Test Method for Cloud Point of Petroleum Products (Linear Cooling Rate Method) D5773 Test Method for Cloud Point of Petroleum Products (Constant Cooling Rate Method) D6079 Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) D6217 Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration D6371 Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels D6468 Test Method for High Temperature Stability of Middle Distillate Fuels D6469 Guide for Microbial Contamination in Fuels and Fuel Systems D6751 Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels D6890 Test Method for Determination of Ignition Delay and Derived Cetane Number (DCN) of Diesel Fuel Oils by Combustion in a Constant Volume Chamber D7371 Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method) D7397 Test Method for Cloud Point of Petroleum Products (Miniaturized Optical Method) E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

Other Standards

EN15751 Automotive fuels – Fatty acid methyl ester (FAME) fuel and blends with diesel fuel – Determination of oxidation stability by accelerated oxidation method

Keywords

biodiesel; biodiesel blend; diesel; fuel oil; petroleum and petroleum products; Biodiesel blend; Fuel oils; Biodiesel; Petroleum products;

ICS Code

ICS Number Code 75.160.20 (Liquid fuels)

DOI: 10.1520/D7467-10 ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]