ASTM-F406 2011

$58.50

F406-11b Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

Published By	Publication Date	Number of Pages
ASTM	2011	39

Guaranteed Safe Checkout

Categories: 97.220.30 - Indoor sports equipment, 97.220.40 - Outdoor and water sports equipment, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard.

1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping and playing accommodations for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changing table, or similar accessories to a non-full size crib/play yard. These accessories shall also comply with the applicable requirements of ASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply with the applicable requirements in Specification F2388 . This specification does not cover inflatable products.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1This consumer safety specification includes the following sections:

PDF Catalog

PDF Pages	PDF Title
1	Scope
3	Referenced Documents Terminology
4	Calibration and Standardization General Requirements
7	Performance Requirements for Rigid Sided Products
9	Performance Requirements for Mesh/Fabric Products
10	Test Methods TABLE 1
17	Marking and Labeling
19	Instructional Literature Keywords A1. FIGURES A1.1
20	FIG. A1.1 FIG. A1.2 FIG. A1.3
21	FIG. A1.4
22	FIG. A1.5 FIG. A1.6
23	FIG. A1.7
24	FIG. A1.8 FIG. A1.9
25	FIG. A1.10 FIG. A1.11
26	FIG. A1.12
27	FIG. A1.13 FIG. A1.14
28	FIG. A1.15 FIG. A1.16
29	FIG. A1.17
30	FIG. A1.18
31	FIG. A1.19 FIG. A1.20 FIG. A1.21 FIG. A1.22
32	FIG. A1.23
33	FIG. A1.24
34	FIG. A1.25 FIG. A1.26 FIG. A1.27 FIG. A1.28
35	FIG. A1.29 FIG. A1.30 FIG. A1.31 FIG. A1.32
36	FIG. A1.33 FIG. A1.34
37	FIG. A1.35
38	A2. DESIGN GUIDELINES FOR PROTRUSIONS A2.1 Purpose and Scope A2.2 Guidelines FIG. A1.36 FIG. A1.37

Additional information

Occupant	3.1.17
Keywords	11
Mesh/Fabric Attachment Strength Test Method	8.16
Corner Post	3.1.4
Structural Failure	3.1.26
Test Procedure for Latches to Prevent Folding of a Foldable Side or End	8.6.5
Paper Label	3.1.18
Top Rail Configuration Test	8.29
Nonpaper Label	3.1.16
Warning Statements	10.1.2
Movable Side Latch Tests	8.6.3
Top Rail to Corner Post Attachment Test	8.30
Adhesion Test	8.19
Mesh/Fabric Attachment Strength	7.8.3
Play Yard	3.1.19
Removal of Protective Components	8.21
Cord	3.1.3
Crib Side Static Test	8.9.5
Labeling	9.1
Test for Stability of Product	8.17
Component-Spacing Test Method	8.2
Cord/Strap Length Test Method	8.24
Crib Side Spindle/Slat Torque Test	8.9.6
Dropside/Dropgate	3.1.5
Dynamic Load	3.1.6
Water Mattress Use	10.3.3
Seam Strength	7.8.2
Mattress	5.16
Top Rail to Corner Post Attachment	7.11
Mattress for Rigid Sided Products	5.17
Hinged Drop Gate Latch Test	8.6.4
Spacing of Unit Components	6.3
Federal Regulations	2.4
Plastic Teething Rail Test for Rigid Sided Products	8.4
Floor Strength Test for Mesh/Fabric Cribs	8.12
False Latch	8.27
Openings	5.9
Scope	1
Test Methods	8
Marking and Labeling	9
Fabric Strength	7.7.1
Static Load	3.1.23
Test for Attachment of Storage Pouch or Other Parts with Printed Warnings	8.23
Floor Strength	7.4
Height of Sides	7.2
Title	Section
Sewn Assembly	7.8.1
Top Rail Configuration	7.10
Record Keeping	5.20
Folding Latch Test Method	8.13.2
Side or End Latch Test, or Both, for Rigid Sided Products	8.6
Requirements for Cutouts	6.7
Construction and Finishing	6.6
Hardware	6.4
Crib Side Cyclic Tests	8.9.4
Test Requirements for Cutouts	8.3
Torque Test	8.21.3
Cyclic Test	8.5
Crib-Side Height	6.2
Mattress Support System Vertical Impact Test Requirements	6.14
Load Application Procedure	8.30.3
Mesh Openings	7.6.1
Dropgate Latch Testing	6.13.1
Protective Components	5.10
Performance Requirements for Rigid Sided Units	6
Referenced Documents	2
Mesh	3.1.12
Entrapment Tests	8.26
Mesh Opening Test	8.14
Key Structural Elements	3.1.9
Stability	5.12
Mattress Support System Testing	6.15
Design Guidelines for Protrusions	Annex A2
Mattress Vertical Displacement Test	8.28
Corner Posts	5.1
General Requirements	5
Side Deflection and Strength Tests for Mesh/Fabric Cribs	8.11
Spindle/Slat Static Load Strength	8.10
Protrusion	3.1.20
Instructional Literature	10
Manufacturer's Recommended Use Position	3.1.10
Mesh Requirements	7.6
Mesh/Fabric Assembly Requirements	7.8
Side Deflection and Strength	7.3
Fasteners	6.5
Permanency of Labels and Warnings	8.18
Top Rail V-Shape Configuration Test	8.29.2
Conspicuous	3.1.2
Definitions of Terms Specific to This Standard	3.1
Spindle/Slat Strength Testing	6.17
Foldable Side or End	3.1.8
Protrusions	8.25
Mattress Support System Vertical Impact Test for Rigid Sided Products	8.7
Entrapment in Accessories	5.15
Plastic Teething Rail	6.11
Mesh Strength	7.6.2
Fabric Material Requirements	7.7
Vinyl Thickness Measurement	8.22
Test for Strength of Mesh and Integrity of Attachment	8.15
Locking Mechanism Test	8.13
Nonpaper Labels	8.20
Coil Springs	5.14
Rigid Sided Crib	3.1.21
Minimum Space when Folded	8.29.1
Mattress Support System Test for Rigid Sided Products	8.8
Latching and Locking Mechanisms	5.8
ASTM Standards	2.1
Dropgate Locking Device Test Method	8.13.1
Cord/Strap Length	5.13
Mesh/Fabric Crib	3.1.13
Crib Side Test Requirements	6.16
Component Spacing Test Apparatus	8.1
Side(s) or End(s) Latch Testing, or Both	6.13
Scissoring, Shearing, or Pinching	5.6
Stationary Side	3.1.24
Calibration and Standardization	4
Performance Requirements for Mesh/Fabric Units	7
Foldable Side or End Latch Testing	6.13.2
Terminology	3
Mattress Vertical Displacement	7.9
Tension Test	8.21.4
Top Rail Covering Material	7.5
Fabric	3.1.7
Crib Side Test	8.9
Seam	3.1.22
ICS Codes	97.220.30 - Indoor sports equipment 97.220.40 - Outdoor and water sports equipment

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-F406 2011

PDF Catalog

Related products