AWWA C153 2019
$76.92
AWWA C153-19 Ductile-Iron Compact Fittings
| Published By | Publication Date | Number of Pages |
| AWWA | 2019 | 56 |
This standard describes 3-in. through 64-in. (80-mm through 1,600-mm) ductile-iron compact fittings to be used with ductile-iron pipe or pipe made of other materials with similar outside diameters for conveying potable water, wastewater, and reclaimed water. Fittings with mechanical joints are listed in this standard for the 3-in. through 64-in. (80-mm through 1,600-mm) sizes. Fittings with push-on joints and flanged joints are listed in this standard for the 54-in. through 64-in. (1,400-mm through 1,600-mm) sizes.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 12 | II.C. Connecting Fittings and Aged Cast-iron Pipe. Fittings should be connected carefully to aged existing cast-iron pipe. The outside diameter of aged pipe should be measured before cutting because some older pipe was manufactured to a larger diameter th |
| 13 | II.D. Advisory Information on Product Testing. The standard acceptance test for static castings is a tensile test from a coupon cast from the same iron. This is typically done with a separately cast ASTM A536 keel block, a modified keel block, or a Y-bloc II.E. Advisory Information for the Purchaser and Specifier. Purchasers and specifiers should be aware that although products may be available that meet the intent of this standard, they may vary in dimensions, characteristics, material properties, or othe II.F. Chlorine and Chloramine Degradation of Elastomers. The selection of materials is critical for water service and distribution piping in locations where there is a possibility that elastomers will be in contact with chlorine or chloramines. Documented |
| 14 | IV. Major Revisions. The major revisions in this edition of ANSI/AWWA C153/A21.53 are as follows: III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. III.A. Purchaser Options and Alternatives. The following items should be provided by the purchaser: III.B. Modification to Standard. Any modification of the provisions, definitions, or terminology in this standard must be provided by the purchaser. |
| 15 | V. Comments. If you have any comments or questions about this standard, please call AWWA Engineering and Technical Services at 303.794.7711, FAX at 303.795.7603, write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098, or e-mail at stand |
| 17 | AWWA Standard SECTION 1: GENERAL Sec. 1.1 Scope |
| 18 | Sec. 1.2 Purpose Sec. 1.3 Application SECTION 1: REFERENCES |
| 19 | SECTION 1: DEFINITIONS |
| 20 | SECTION 1: REQUIREMENTS Sec. 4.1 Materials Sec. 4.2 Permeation Sec. 4.3 General Requirements |
| 21 | Sec. 4.4 Coatings and Linings |
| 22 | Sec. 4.5 Tolerances or Permitted Variations |
| 23 | Sec. 4.6 Markings on Fittings Sec. 4.7 Special Requirements for Flanged Fittings |
| 24 | SECTION 5: VERIFICATION Sec. 5.1 Inspection |
| 25 | Sec. 5.2 Test Procedures |
| 26 | Sec. 5.4 Additional Tests Required by Purchaser Sec. 5.5 Performance Requirements Sec. 5.6 Defective Specimens and Retests Sec. 5.7 Nonconforming Fittings |
| 27 | SECTION 6: DELIVERY |
