AWWA C522 2022

$76.92

AWWA C522-22 Rotary Cone Valves, 6 In. Through 60 In. (150 mm Through 1,500 mm)

Published By	Publication Date	Number of Pages
AWWA	2022

Guaranteed Safe Checkout

Category: AWWA

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This standard covers gray-iron, ductile-iron, and cast or weld fabricated-steel or stainless steel flanged-end, low-leakage trunnion-mounted, full-port, two (2)- and four (4)-seated rotary cone valves for pressures up to 300 psi (2,100 kPa) in sizes from 6-in. through 60-in. (150-mm through 1,500-mm) diameter for use in water, wastewater, and reclaimed water systems having water with a pH greater than 6 and less than 12 and with temperatures greater than 32

PDF Catalog

PDF Pages	PDF Title
9	Foreword I. Introduction. I.A. Background. A type of quarter turn plug valve, rotary cone valves have been used in pipelines carrying water for more than 95 years. Manufacturers of rotary cone valves have developed rotary cone valves using metal-to-metal seats. This standard cover I.B. History. This first edition of ANSI/AWWA C522-22, Rotary Cone Valves, 6 In. Through 60 In. (150 mm Through 1,500 mm), was approved on October 24, 2022. I.C. Acceptance. In May 1985, the US Environmental Protection Agency (USEPA) entered into a cooperative agreement with a consortium led by NSF International (NSF) to develop voluntary third-party consensus standards and a certification program for direct
10	II. Special Issues. II.A. General. The actuating forces required to operate a rotary cone valve of a given size vary considerably and depend on the size of the valve, the differential operating pressure, the quantity of water flow, the configuration of waterway passages, and
11	II.B. Considerations for Throttling Service. If a valve is to be installed for throttling service, the system owner, system designer, or purchaser must carefully evaluate the full range of differential pressures across the valve versus the downstream pres II.C. Valve and Piping Supports. To maintain the integrity of the valve, it is important to avoid subjecting the valve to pipe loads or external loads that drive the valve out of round, such as the use of valve foundations or supports without proper pipe II.D Permeation. The selection of materials is critical for water service and distribution piping in locations where there is likelihood the pipe will be exposed to significant concentrations of pollutants composed of low-molecular-weight petroleum produc
12	II.E. Valve Installation and Piping Design. The installation of rotary cone valves downstream of turbulence-inducing devices or pieces of equipment, such as pumps and piping fittings, requires some consideration to avoid various mechanical and hydraulic i
13	II.F. Effects of Manual or Power Actuation Stroke Time. When specifying manual and power actuators in Sec. III.A, Items 4, 23, 25, 26, and 27, consideration should be given to the effects of speed of valve operation on the pipeline hydraulic transients (s II.G. Chlorine and Chloramine Degradation of Elastomers. The selection of materials is critical for water service and distribution piping in locations where there is a possibility that elastomers will be in contact with chlorine or chloramines. Documented II.H. Valve body/conical plug taper angle. Since the first rotary cone valve introduced in 1926, there have been multiple taper angles employed in their design/construction including 9 degrees, 1-1/2 inches/12 inches (1 mm/8 mm), 7 degrees, 5 degrees, 1 i
14	II.I. Integrally Cast or Welded Trunnions v Bolted Trunnions. Rotary cone valves were first introduced in 1926 incorporating bolted-on trunnions in lower body and upper plug design. This resulted in too many degrees of freedom and concentricity issues res II.J Bolting Gray Cast Iron Flanges to Steel Flanges. The following recommendations are made for the use of high strength bolting used with either ASME or AWWA steel flanges when bolting to low ductility gray cast iron valve flanges. The ASME B16.1 standa
15	II.K Finite Element Analysis (FEA). Advisory Information on Valve Design. Calculation tools like FEA software can be used as a supplement to the equations, wall thickness tables, and size tables when listed in this standard for stress design. These calcul III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. III.A. System Owner, System Designer, or Purchaser Options and Alternatives. The following items or information should be provided by the system owner, system designer, or purchaser:
17	III.B. Modification to Standard. Any modification to the provisions, definitions, or terminology in this standard must be provided in the purchase documents.
19	AWWA Standard SECTION 1: GENERAL Sec. 1.1 Scope Table 1 Pressure classes and rated/design pressure and fluid velocity
20	Sec. 1.2 Purpose Sec. 1.3 Application Sec. 1.4 Valve Construction Sec. 1.5 Description of Operation SECTION 2: REFERENCES
23	SECTION 3: DEFINITIONS
27	Sec. 4.2 Materials
28	Sec. 4.3 Design
29	Table 2 Minimum Body Shell Thickness for Bodies
37	Table 3 Operating mechanism and actuator application factors (AF)
42	Sec. 4.6 Assembly of Pressure Boundary Bolted Flange Joint Assemblies. SECTION 5: VERIFICATION Sec. 5.1 Production Testing
44	Sec. 6.3 Handling, Storage, and Installation
45	APPENDIX A Installation, Operation, and Maintenance of Rotary Cone Valves
51	Sample – Certified Test Report for Rotary Cone Valves
53	Sample – Quotation/Order Specific Requirements for Rotary Cone Valves