🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
AWWA C906 2007

AWWA C906 2007

$75.83

AWWA C906-07: Polyethylene (PE) Pressure Pipe & Fittings 4 In (100 MM) Thru 63 In (1,575 MM) For Water Distribution And Transmission

Published By Publication Date Number of Pages
AWWA 2007 52
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This standard describes polyethylene (PE) pressure pipe made from materials conforming to standard PE code designations PE 2406, PE 3406, and PE3408.

PDF Catalog

PDF Pages PDF Title
1 ANSI/AWWA C906-07
3 Committee Personnel
5 Contents
7 Foreword
I. Introduction.
9 II. Special Issues.
10 III. Use of This Standard.
11 IV. Major Revisions.
V. Comments.
13 AWWA Standard Polyethylene (PE) Pressure Pipe
and Fittings, 4 In. (100 mm) Through
63 In. (1,600 mm), for Water
Distribution and Transmission

SECTION 1: GENERAL
Sec. 1.1 Scope
14 Sec. 1.2 Purpose
Sec. 1.3 Application
SECTION 2: REFERENCES
16 SECTION 3: DEFINITIONS
18 SECTION 4: REQUIREMENTS
Sec. 4.1 Permeation
Sec. 4.2 Materials
19 Table 1 PE pipe and fittings materials
20 Table 2 Elevated-temperature [176 ± 3.6°F (80 ± 2°C)] sustained-pressure test
Sec. 4.3 Pipe Requirements
22 Table 3 Outside diameters (ODs) and tolerances
23 Table 4 Minimum wall thicknesses (in.), IPS sizing system
24 Table 5 DI: Outside diameters (ODs) and tolerances
25 Table 6 DI: Minimum wall thicknesses (in.) for ductile-iron sizing system (DIOD)
26 Table 7 Outside diameters and tolerances
27 Table 8 Minimum wall thicknesses
29 Sec. 4.4 Fusion Fittings Requirements
30 Sec. 4.5 Joining Methods
31 Sec. 4.6 Pipe Classification and Working Pressure Rating
33 Table 9 Pressure class/maximum working pressure rating (see note)
34 Table 10 Temperature compensation multipliers
35 SECTION 5: VERIFICATION
Sec. 5.1 General
Sec. 5.2 Material Testing Requirements
36 Sec. 5.3 Manufacturer Qualification
Sec. 5.4 Pipe Testing Requirements
37 Sec. 5.5 Fitting Testing Requirements
Sec. 5.6 Provision for Test Sample Failure
Sec. 5.7 Bend-Back Test
39 Sec. 5.8 Plant Inspection by Purchaser
SECTION 6: DELIVERY
Sec. 6.1 Marking
40 Sec. 6.2 Shipping
Sec. 6.3 Affidavit of Compliance
41 APPENDIX A Bibliography

SECTION A.1: GENERAL REFERENCES
43 APPENDIX B Pipe Classification and Working Pressure Rating

SECTION B.1: PRESSURE SURGE CAPACITY
Table B.1 Allowable maximum surge pressure surges above working pressure (WP) and
corresponding estimated maximum allowable sudden change in water velocity for pipe operating at
80°F (27°C) and at a maximum working pressure (WP) equal to the pipe’s nominal pressure class
(PC)
45 APPENDIX C Working Pressure Rating and Pressure Class

Sec. C.1 Working Pressure Rating and Pressure-Class Selection—Examples
Table C.1 Surge pressure per foot of extinguished velocity by pipe DR for PE 3408 materials
47 Table C.2 Working pressure rating by DR for velocity changes for PE 3408 materials

Related products

AWWA C906 2007
$75.83