AWWA E102 2023

$76.92

AWWA E102-23 Submersible Vertical Turbine Pumps

Published By	Publication Date	Number of Pages
AWWA	2023	48

Guaranteed Safe Checkout

Category: AWWA

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This standard provides minimum requirements for submersible vertical turbine pumps utilizing a discharge column pipe assembly for installation in wells, water treatment plants, water transmission systems, and water distribution systems. Electric motors are the only type of prime movers addressed in this standard. It can be referenced in purchase documents for submersible vertical turbine pumps. Purchasers of submersible vertical turbine pumps that are intended to operate outside of the performance parameters and conditions defined in this standard are advised to consult with pump manufacturers familiar with the intended application conditions to modify the requirements of this standard as necessary for suitability with the specific conditions of intended use.

PDF Catalog

PDF Pages	PDF Title
7	Foreword I. Introduction. I.A. Background. This standard describes the minimum requirements for submersible vertical turbine pumps utilizing a discharge column pipe assembly for installation in wells, water treatment plants, water transmission systems, and water distribution syste I.B. History. The original standard for vertical line-shaft turbine pumps presented the composite findings from studies conducted from 1949 to 1986 by committees consisting of manufacturers, consumers, and engineers. The first standard was published in 19
8	I.C. Acceptance. In May 1985, the US Environmental Protection Agency (USEPA) entered into a cooperative agreement with a consortium led by NSF International* (NSF) to develop voluntary third-party consensus standards and a certification program for direct
9	II. Special Issues. II.A. General. A pumping system consists of several components: the pump, the driver, the discharge column pipe and discharge elbow, the baseplate, the foundation, the controls, the discharge piping, and in most cases the well casing or suction barrel. Th
11	II.B. Chlorine and Chloramine Degradation of Elastomers. The selection of materials is critical for water service and distribution piping in locations where there is a possibility that elastomers will be in contact with chlorine or chloramines. Documented II.C. Advisory Information on Product Application. This standard does not cover all applications or manufacturing technologies. Some waters may have high conductivity levels well in excess of 200 μΩ/cm, for which it may be advisable to consult with a meta
12	II.D. Pump Tests.
13	II.E. Vibration Limits. The vibration characteristics of a pumping system depend on a combination of pump and driver design and construction, column piping design and construction, baseplate or mounting plate design and construction, support foundation de
14	III.A. Information for Manufacturers. Pump manufacturers require basic data to provide pumps meeting purchasers’ needs. This includes, at minimum, a definition of required operating conditions. When placing orders for pumps to be manufactured in accordanc
16	III.B. Purchaser Options and Alternatives. The following items should be provided by the purchaser: III.C. Modification to Standard. Any modification of the provisions, definitions, or terminology in this standard must be provided by the purchaser. IV. Major Revisions
17	V. Comments. If you have any comments or questions about this standard, please call the AWWA Engineering and Technical Services at 303.794.7711, write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098; or e-mail at [email protected].
19	AWWA Standard SECTION 1: GENERAL Sec. 1.1 Scope Sec. 1.2 Purpose Sec. 1.3 Application
20	SECTION 2: REFERENCES
21	SECTION 3: DEFINITIONS
28	Figure 1 Typical submersible-pump assembly (bowl assemblies)
29	Figure 2 Submersible-pump discharge styles and surface-plate assemblies
37	Table 2 Diameters and weights of standard discharge column pipe sizes
43	APPENDIX A Submersible Vertical Turbine Pump Data Form
45	Engineering Data