BS EN 10216-2:2013
$189.07
Seamless steel tubes for pressure purposes. Technical delivery conditions – Non-alloy and alloy steel tubes with specified elevated temperature properties
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 50 |
This European Standard specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel. This Part of EN 10216 may also be applied for tubes of non-circular cross section; necessary modification should be agreed at the time of enquiry and order. NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Contents Page |
| 6 | Foreword |
| 7 | Introduction |
| 8 | 1 Scope 2 Normative references |
| 9 | 3 Terms and definitions 4 Symbols |
| 10 | 5 Classification and designation 5.1 Classification 5.2 Designation 6 Information to be supplied by the purchaser 6.1 Mandatory information |
| 11 | 6.2 Options 6.3 Examples of an order 6.3.1 Example 1 |
| 12 | 6.3.2 Example 2 7 Manufacturing process 7.1 Steel making process 7.2 Tube manufacture and delivery conditions |
| 13 | 8 Requirements 8.1 General |
| 14 | 8.2 Chemical composition 8.2.1 Cast analysis 8.2.2 Product analysis |
| 18 | 8.3 Mechanical properties 8.3.1 Mechanical properties at and below room temperature 8.3.2 Proof strength at elevated temperature 8.3.3 Creep rupture strength |
| 23 | 8.4 Appearance and internal soundness 8.4.1 Appearance 8.4.2 Internal soundness 8.4.2.1 Leak Tightness 8.4.2.2 Non-Destructive Testing 8.5 Straightness 8.6 Preparation of ends |
| 24 | 8.7 Dimensions, masses and tolerances 8.7.1 Diameter and wall thickness |
| 27 | 8.7.2 Mass 8.7.3 Lengths 8.7.4 Tolerances 8.7.4.1 Tolerances on diameter and thickness |
| 28 | 8.7.4.2 Tolerances on exact lengths |
| 29 | 9 Inspection 9.1 Types of inspection 9.2 Inspection documents 9.2.1 Types of inspection documents 9.2.2 Content of inspection documents |
| 30 | 9.3 Summary of inspection and verification testing |
| 31 | 10 Sampling 10.1 Frequency of tests 10.1.1 Test unit 10.1.2 Number of sample tubes per test unit 10.2 Preparation of samples and test pieces 10.2.1 Selection and preparation of samples for product analysis 10.2.2 Location, orientation and preparation of samples and test pieces for mechanical test 10.2.2.1 General 10.2.2.2 Test pieces for tensile tests |
| 32 | 10.2.2.3 Test pieces for flattening test, ring tensile test, drift expanding test and ring expanding test 10.2.2.4 Test pieces for impact test 11 Verification test methods 11.1 Chemical analysis |
| 33 | 11.2 Tensile test 11.2.1 Tensile test at room temperature 11.2.2 Tensile test at elevated temperature 11.3 Flattening test |
| 34 | 11.4 Ring tensile test 11.5 Drift expanding test |
| 35 | 11.6 Ring expanding test |
| 36 | 11.7 Impact test 11.8 Leak tightness test 11.8.1 Hydrostatic test |
| 37 | 11.8.2 Electromagnetic test 11.9 Dimensional inspection 11.10 Visual examination 11.11 Non-destructive testing 11.12 Material identification |
| 38 | 11.13 Retests, sorting and reprocessing 12 Marking 12.1 Marking to be applied 12.2 Additional marking 13 Protection |
| 39 | Annex A (informative) Creep rupture strength values |
| 45 | Annex B (informative) Technical changes from the previous edition B.1 Introduction B.2 Technical changes |
| 46 | Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC |
| 47 | Bibliography |
