BS EN 1279-5:2018 – TC:2020 Edition
$217.84
Tracked Changes. Glass in building. Insulating glass units – Product standard
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 101 |
This document covers the product standard of insulating glass units (IGU) for use in buildings. Units for which the intended use is only artistic and therefore no essential characteristics are required, are not subject to CE marking and are not part of this standard. NOTE For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 61 | undefined |
| 67 | 1 Scope 2 Normative references |
| 68 | 3 Terms and definitions |
| 70 | 4 Requirements 4.1 Product description 4.2 Determination of the characteristic’s performances 4.2.1 Characteristics of glass panes for use in insulating glass units 4.2.1.1 General |
| 71 | 4.2.1.2 Glass panes used as components for the production of insulating glass units 4.2.2 Determination of characteristics of insulating glass units 4.2.2.1 General 4.2.2.2 Safety in the case of fire – Resistance to fire 4.2.2.3 Safety in the case of fire – Reaction to fire |
| 72 | 4.2.2.4 Safety in the case of fire – External fire performance (for roof coverings only) 4.2.2.5 Safety in use – Bullet resistance: shatter properties and resistance to attack |
| 73 | 4.2.2.6 Safety in use – Explosion resistance: shatter properties and resistance to impact 4.2.2.7 Safety in use – Burglar resistance shatter properties and resistance to attack |
| 74 | 4.2.2.8 Safety in use – Pendulum body impact resistance: shatter properties (safe breakability) and resistance to impact 4.2.2.9 Safety in use – Mechanical resistance: Resistance against sudden temperature changes and temperature differentials 4.2.2.10 Safety in use – Mechanical resistance: Resistance against wind, snow, permanent load and/or imposed loads of the glass unit |
| 75 | 4.2.2.11 Protection against noise – Direct airborne sound reduction 4.2.2.12 Energy conservation and heat retention – Thermal properties 4.2.2.13 Energy conservation and heat retention – Radiation properties: Light transmittance and reflectance |
| 76 | 4.2.2.14 Energy conservation and heat retention – Radiation properties: Solar energy characteristics 4.2.2.15 Durability / Conformity with the definition of insulating glass unit |
| 78 | 4.3 Characteristics other than listed in 4.2 5 Assessment and verification of constancy of performance – AVCP 5.1 General 5.2 Determination of the product type (see 5.1, 1) 5.2.1 General |
| 79 | 5.2.2 Type testing of characteristic’s performances 5.2.3 Test reports |
| 80 | 5.2.4 Multiple lines/sites 5.3 Factory Production control (FPC) 5.3.1 General 5.3.2 Inspection of samples in accordance with a prescribed test plan (see 5.1 2a) |
| 81 | 5.4 Initial inspection of factory and of factory production control (5.1 2b) |
| 82 | 5.5 Continuous surveillance and assessment of the factory production control (5.1 2c) |
| 83 | 5.6 Procedure for modifications 5.7 Pre-production products (e.g. prototypes) |
| 84 | 6 Marking and/or labelling 6.1 General 6.2 Product marking |
| 85 | Annex A (normative)Safety in use – Mechanical resistance: Resistance against wind, snow, permanent load and/or imposed loads of the glass unit |
| 87 | Annex B (normative)Effect of gas filling on thermal and sound insulation performances: B.1 Determination of the value to be declared |
| 88 | B.2 Example with krypton gas filling |
| 90 | Annex C (informative)Installation of Insulating Glass Units C.1 General C.2 Appropriate supports C.3 Installation and glazing conditions C.3.1 General |
| 91 | C.3.2 Compatibility C.3.3 Protection of the edge seal against ultraviolet radiation C.3.4 Pressure limits on glass and prevention of frictional movements C.3.5 Prevention of contact of glass with support |
| 92 | Annex D (normative)Rules for the use of other party TT results D.1 General D.2 Manufacturer supplying the other party TT results |
| 93 | D.3 Manufacturer using the other party TT results |
| 94 | Annex E (informative)Provisions for voluntary involvement of third party(ies) E.1 General E.2 Voluntary tasks for third parties E.3 Marking and labelling |
| 95 | Annex ZA (informative)Relationship of this European Standard with Regulation (EU) No.305/2011 |
