BS EN 13493:2018
$198.66
Geosynthetic barriers. Characteristics required for use in the construction of solid waste storage and disposal sites
| Published By | Publication Date | Number of Pages |
| BSI | 2018 | 58 |
This European Standard specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers and separation layer in the construction of solid waste storage and disposal sites, and the appropriate test methods to determine these characteristics. The intended use of these products is to control the leakage of fluids through the construction. This European Standard is not applicable to geotextiles or geotextile-related products as defined in EN ISO 10318-1. This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures. This European Standard defines characteristics to be considered with regard to the presentation of performance. NOTE Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | National foreword |
| 5 | European foreword |
| 6 | Introduction |
| 7 | 1 Scope 2 Normative references |
| 10 | 3 Terms, definitions and abbreviations 3.1 Terms and definitions |
| 11 | 3.2 Abbreviations |
| 12 | 4 Characteristics and corresponding methods of test 4.1 General 4.2 Types of application 4.2.1 General 4.2.2 Application 1: “Composite lining system” |
| 13 | 4.2.3 Application 2: “Single lined system” |
| 14 | 4.3 Relevant characteristics |
| 20 | 4.4 Characteristics relevant to specific conditions of use 4.4.1 General 4.4.2 Gas permeability 4.4.3 Burst strength and elongation 4.4.4 Tear strength 4.4.5 Friction characteristics (direct shear and inclined plane tests) |
| 21 | 4.4.6 Low temperature behaviour 4.4.7 Weathering 4.4.8 Resistance to wetting and drying 4.4.9 Freeze–thaw cycle resistance 4.4.10 Resistance to root penetration 4.5 Release of dangerous substances |
| 22 | 5 Assessment and verification of constancy of performance (AVCP) 5.1 General 5.2 Type testing 5.2.1 General |
| 23 | 5.2.2 Test samples, testing and compliance criteria 5.2.3 Test reports 5.2.4 Shared other party results |
| 24 | 5.2.5 Cascading determination of the product type results |
| 25 | 5.3 Factory production control (FPC) 5.3.1 General 5.3.2 Requirements |
| 29 | 5.3.3 Product specific requirements |
| 30 | 5.3.4 Initial inspection of factory and of FPC 5.3.5 Continuous surveillance of FPC |
| 31 | 5.3.6 Procedure for modifications 5.3.7 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity |
| 32 | Annex A (normative) Durability of geosynthetic barriers |
| 52 | Annex ZA (informative) Relationship of this European Standard with Regulation (EU) No. 305/2011 |
| 55 | Bibliography |
Related products
-
BS EN 13493:2018 – TC:2020 Edition
Tracked Changes. Geosynthetic barriers. Characteristics required for use in the construction of solid waste storage…
-
BS EN 13493:2018 – TC:2020 Edition
Tracked Changes. Geosynthetic barriers. Characteristics required for use in the construction of solid waste storage…
