BS EN 13707:2013
$167.15
Flexible sheets for waterproofing. Reinforced bitumen sheets for roof waterproofing. Definitions and characteristics
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 44 |
This European Standard specifies definitions and characteristics for flexible reinforced bitumen sheets for which the intended use is roofing. This covers sheets used as top layers, intermediate layers and underlayers. It does not cover reinforced bitumen sheets for waterproofing used as underlays for discontinuous roofing.
This European Standard does not cover waterproofing sheets which are intended to be used fully bonded under bituminous products (e.g. asphalt) directly applied at high temperature, specified by EN 14695.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 7 | 1 Scope 2 Normative references |
| 8 | 3 Terms and definitions |
| 10 | 4 System-related characteristics 5 Product characteristics 5.1 General 5.2 Characteristics 5.2.1 Visible defects 5.2.2 Dimensions, tolerances and mass per unit area 5.2.3 Watertightness 5.2.4 Effects of water |
| 11 | 5.2.5 Fire performance 5.2.5.1 External fire performance 5.2.5.2 Reaction to fire 5.2.6 Resistance to hail 5.2.7 Watertightness after stretching at low temperature |
| 12 | 5.2.8 Joint strength 5.2.9 Water vapour properties 5.2.10 Tensile properties 5.2.11 Resistance to impact 5.2.12 Resistance to static loading 5.2.13 Resistance to tearing (nail shank) 5.2.14 Resistance to root penetration 5.2.15 Dimensional stability 5.2.16 Form stability under cyclic temperature change |
| 13 | 5.2.17 Flexibility at low temperature (pliability) 5.2.18 Flow resistance at elevated temperature 5.2.19 Artificial ageing behaviour 5.2.19.1 Top layers and single layers with permanent light surface protection 5.2.19.2 Top layers and single layers without surface protection 5.2.19.3 Top layers with permanent heavy surface protection, underlayers and intermediate layers |
| 14 | 5.2.20 Adhesion of granules 5.3 Dangerous substances 6 Evaluation of conformity 6.1 General 6.2 Initial Type Testing – Type Testing 6.2.1 General |
| 15 | 6.2.2 Test reports 6.3 Factory production control (FPC) 6.3.1 General |
| 16 | 6.3.2 Requirements 6.3.2.1 General 6.3.2.2 Equipment 6.3.2.2.1 Testing |
| 17 | 6.3.2.2.2 Manufacturing 6.3.2.3 Raw materials and components 6.3.2.4 Design process 6.3.2.5 Controls during manufacturing process 6.3.2.6 Product testing and evaluation 6.3.2.7 Non-complying products 6.3.2.8 Corrective action 6.3.2.9 Handling, storage and packaging 6.3.3 Product specific requirements |
| 18 | 6.3.4 Initial inspection of factory and of FPC |
| 19 | 6.3.5 Continuous surveillance of FPC 6.3.6 Procedure for modifications 7 Product data sheet |
| 20 | 8 Marking, labelling and packaging |
| 21 | Annex A (normative) Applicability of characteristics |
| 22 | Annex B (normative) Frequencies of testing for factory production control |
| 23 | Annex C (informative) Information about chemical resistance |
| 25 | Annex D (informative) Example of a product data sheet ( General information |
| 26 | Table D.1 (concluded) |
| 27 | Annex E (informative) Wind-uplift properties of mechanically fixed bituminous membranes ( General information |
| 28 | Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives ZA.1 Scope and relevant characteristics |
| 30 | ZA.2 Procedure for attestation of conformity of the bitumen sheets ZA.2.1 Systems of attestation of conformity |
| 36 | ZA.2.2 EC Certificate and Declaration of conformity ZA.2.2.1 In case of products following Table ZA.3.1 or ZA.3.2 |
| 37 | ZA.2.2.2 In case of products following Tables ZA.3.3 to ZA.3.6 |
| 38 | ZA.3 CE marking and labelling |
