BS EN 14216:2015 – TC:2020 Edition
$186.33
Tracked Changes. Cement. Composition, specifications and conformity criteria for very low heat special cements
Published By | Publication Date | Number of Pages |
BSI | 2020 | 64 |
This European Standard defines and gives the specifications of six distinct very low heat special cement products and their constituents. The definition of each cement includes the proportions in which the constituents are to be combined to produce these distinct products in a single strength class having a limited heat of hydration value. The definition also includes requirements the constituents have to meet and the mechanical, physical, chemical and heat of hydration requirements for these products. This European Standard also states the conformity criteria and the related rules. Necessary durability requirements are also given. In addition to the specified requirements, an exchange of additional information between the cement producer and user can be helpful. The procedures for such an exchange are not within the scope of this European Standard but should be dealt with in accordance with national standards or regulations or can be agreed between the parties concerned. NOTE 1 The word ‘cement’ in this European Standard is used to refer to very low heat special cement unless otherwise indicated. NOTE 2 The risk of early-age thermal cracking in concrete depends upon the properties and execution and is, therefore, also dependent on factors other than the heat of hydration of the cement.
PDF Catalog
PDF Pages | PDF Title |
---|---|
40 | 0BContents Page Contents Page |
41 | European foreword |
42 | Introduction |
43 | 1 Scope 2 Normative references 3 Terms and definitions |
44 | 4 Very low heat special cement 5 Constituents 6 Composition and notation |
45 | Table 1 — The 6 products in the family of very low heat special cements |
46 | 7 Mechanical, physical, heat of hydration, chemical and durability requirements 7.1 Mechanical requirements – Standard strength Table 2 — Mechanical and physical requirements given as characteristic values 7.2 Physical requirements 7.2.1 Initial setting time 7.2.2 Soundness 7.2.3 Heat of hydration 7.3 Chemical requirements |
47 | Table 3 — Chemical requirements given as characteristic values 7.4 Durability requirements 7.5 Dangerous substances 8 Standard designation |
48 | 9 Conformity criteria 9.1 General requirements |
49 | Table 4 — Properties and test methods and minimum testing frequencies for the autocontrol testing by the manufacturer and the statistical assessment procedure 9.2 Conformity criteria for mechanical, physical and chemical properties and evaluation procedure 9.2.1 General |
50 | 9.2.2 Statistical conformity criteria 9.2.2.1 General Table 5 — Required values Pk and CR 9.2.2.2 Inspection by variables |
51 | Table 6 — Acceptability constant kA 9.2.2.3 Inspection by attributes |
52 | Table 7 — Values of cA 9.2.3 Single result conformity criteria Table 8 — Limit values for single results |
53 | 9.3 Conformity criteria for cement composition 9.4 Conformity criteria for properties of the cement constituents |
54 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Regulation ZA.1 Scope and relevant characteristics |
55 | Table ZA.1 — Relevant clauses |
56 | The declaration of the product performance related to certain essential characteristics is not required in those Member States (MS) where there are no regulatory requirements on these essential characteristics for the intended use of the product. In t… ZA.2 Procedure for AVCP of very low heat special cements ZA.2.1 System of AVCP Table ZA.2 — System of AVCP |
57 | Table ZA.3 — Assignment of AVCP tasks for 6 different very low heat special cement products under system 1+ ZA.2.2 Declaration of performance (DoP) ZA.2.2.1 General |
58 | ZA.2.2.2 Content ZA.2.2.3 Example of DoP |
60 | ZA.3 CE marking and labelling |
61 | Figure ZA.1 — Example CE marking information related to very low heat special cements |
62 | Bibliography |