Shopping Cart

No products in the cart.

BS EN 14404-3:2024

$109.61

Personal protective equipment. Knee protectors for work in the kneeling position – Requirements for the individual combination of knee pads and garments (type 2)

Published By Publication Date Number of Pages
BSI 2024 30
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

This document specifies requirements for the individual combination (type 2) of knee pads with garments and performance levels for use when working in a kneeling position in order to reduce injuries to the knees caused by continuous pressure and penetration. Requirements for the marking of knee pads and garments as well as the information to be supplied by the manufacturer are given. Where protection against additional hazards is claimed, performance requirements from other standards are applicable. This document does not apply to knee protectors that are medical devices or are intended for sports and motorcycles. In this part, requirements are given for a specific combination of an individual pad and accordingly designed garment; these forms of knee protection are thus subject to a joint examination. A combination of a garment with a fixed sized knee pad pocket and fixed sized knee pad (interoperable pad) is described in EN 14404 4 and is excluded from this part. The position of type 2 knee pads in or on trousers can be fixed or adjustable. The pads consist of foam plastic or other materials that are positioned in knee pockets of the garments or permanently fastened in or on the garments.

PDF Catalog

PDF Pages PDF Title
2 undefined
10 1 Scope
2 Normative references
3 Terms and definitions
11 4 Performance levels of knee protectors
5 Requirements
5.1 Summary of the requirements
13 5.2 General requirements
5.2.1 Knee pad
5.2.2 Garment
5.3 Products for testing
5.4 Orientation of the knee pad
5.4.1 Vertical alignment
5.4.2 Identification of left and right knee pad
14 5.5 Specific requirements for knee pads and garments
5.5.1 Size and dimension
5.5.1.1 Size designation of the knee pad
5.5.1.2 Size designation of garment
5.5.1.3 Dimension of protection zone
16 5.5.2 Penetration resistance
5.5.3 Force distribution
5.5.3.1 Force distribution on a flat even surface
5.5.3.2 Force distribution on an uneven surface
5.5.4 Peak transmitted force
5.5.5 Restraint
5.5.5.1 General
5.5.5.2 Restraint of knee pads in knee pockets on garments or knee protectors permanently fastened to garments
17 5.6 Optional requirement – Water resistance
5.7 Ergonomic requirements
5.7.1 Comfort during use on a flat even surface
5.7.2 Comfort during use on an uneven surface
6 Marking
6.1 General
6.2 Specific
6.2.1 Knee pad
18 6.2.2 Garment
20 7 Information to be supplied by the manufacturer
7.1 Knee pad
21 7.2 Garment
22 Annex A (informative)Rationale
A.1 Protection zone
A.1.1 General
A.1.2 Minimum width of the protection zone
A.1.2.1 Small size (patella widths 44 mm to 54 mm)
23 A.1.2.2 Large size (patella widths 55 mm to 64 mm)
A.1.3 Minimum length of the protection zone
A.1.3.1 Small size
A.1.3.2 Large size
A.1.4 Extended protection zone
A.1.4.1 General
A.1.4.2 Small size
24 A.1.4.3 Large size
A.1.4.4 Interoperable knee pad
A.1.5 Extended protection zone for knee mats
25 Annex B (informative)Information on the problems of using knee protectors for work in the kneeling position
B.1 Introduction
B.2 Advice to users
26 Annex C (informative)Information for Type 2 knee protector for arrangement of the knee protection pocket
C.1 Introduction
C.2 Position
27 Annex ZA (informative)Relationship between this European Standard and the essential requirements of Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment aimed to be covered
BS EN 14404-3:2024
$109.61