BS EN 16062:2015
$198.66
Intelligent transport systems. ESafety. eCall high level application requirements (HLAP) using GSM/UMTS circuit switched networks
| Published By | Publication Date | Number of Pages |
| BSI | 2015 | 56 |
In respect of pan-European eCall (operating requirements defined in EN 16072 ), this European Standard defines the high level application protocols, procedures and processes required to provide the eCall service using a TS12 emergency call over a mobile communications network.
NOTE 1
The objective of implementing the pan-European in-vehicle emergency call system ( eCall) is to automate the notification of a traffic accident, wherever in Europe, with the same technical standards and the same quality of services objectives by using a PLMN (such as ETSI prime medium) which supports the European harmonized 112/E112 emergency number (TS12 ETSI/TS 122 003) and to provide a means of manually triggering the notification of an emergency incident.
NOTE 2
HLAP requirements for third party services supporting eCall can be found in EN 16102 , and have been developed in conjunction with the development of this work item, and is consistent in respect of the interface to the PSAP. This deliverable makes reference to those provisions but does not duplicate them.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 9 | 1 Scope 2 Normative references |
| 10 | 3 Terms and definitions |
| 13 | 4 Symbols and abbreviations |
| 14 | 5 Conformance |
| 15 | Figure 1 — End-to-End eCall system extended with conformance test system 6 General overview of the eCall transaction for Pan European eCall |
| 16 | Figure 2 — Relationship of the Pan European eCall process to European Standards Figure 3 — Relationship of eCall transaction to standards |
| 17 | Figure 4 — General overview – MSD sent from IVS to PSAP – successful case |
| 19 | 7 Requirements 7.1 Procedures following power-up of the in-vehicle system 7.1.1 General 7.1.2 Enabled IVS 7.1.3 Enabled PSAP |
| 20 | Figure 5 — Use of the eCall flag 7.1.4 IVS configured only for eCall 7.1.5 Self-test 7.1.6 Standby mode applicable to IVS configured for eCall only |
| 21 | 7.2 Activation 7.2.1 Activation of pan-European eCall 7.2.2 Activation of a test eCall 7.3 Call set-up 7.3.1 General |
| 22 | 7.3.2 IVS network access device (NAD) already registered on PLMN 7.3.3 eCall in progress 7.3.4 Network selection and registration 7.3.5 Authentication of the subscriber |
| 23 | 7.3.6 eCall establishment 7.3.7 Cell localisation (by network) 7.3.8 Manual termination of eCall by vehicle occupants before trigger confirmation 7.4 MSD transfer 7.4.1 General |
| 24 | Figure 6 — MSD transfer – lower layer – successful case 7.4.2 Send initiation signal from IVS eCall modem to PSAP |
| 25 | 7.4.3 eCall modem synchronization 7.4.4 Request MSD by PSAP eCall modem to IVS eCall modem 7.4.5 Send MSD from vehicle IVS to PSAP eCall modem 7.4.6 Link layer error check 7.4.7 Link layer ACK from PSAP eCall modem to IVS eCall modem |
| 26 | 7.5 Application layer acknowledgement (AL- ACK) 7.5.1 Following transmission of the MSD to the eCall PSAP application 7.5.2 PSAP acknowledges the MSD |
| 27 | 7.5.3 No receipt of application layer ACK 7.5.4 Form of presentation of the AL-ACK Table 1 — Form of presentation of the AL- ACK Table 2 — Mapping of application layer ACK bit 4 and bit 3 to binary representation in in-band modem high level acknowledgement message |
| 28 | Table 3 — Mapping of application layer ACK bit 2 and bit 1 to binary bepresentation in in-band modem high level acknowledgement message Figure 7 — Flowchart for the AL-ACK transmission sequence 7.6 PSAP request “SEND MSD” 7.6.1 General 7.6.2 Before call clear-down |
| 29 | Figure 8 — Request “SEND MSD” – successful case |
| 30 | 7.6.3 After call clear-down 7.7 PSAP application features 7.7.1 General requirements |
| 31 | 7.7.2 MSD display to the PSAP operator 7.7.3 PSAP operator user interface 7.8 Audio link to vehicle occupants 7.9 eCall clear-down |
| 32 | 7.10 PSAP call back 7.11 Rerouting to another PSAP/emergency control centre |
| 33 | 7.12 Handling non equipped situations / error cases 7.12.1 MSD not transmitted correctly 7.12.2 Network registration fails 7.12.3 Call failure before the MSD is sent and acknowledged 7.12.4 Mobile network not supporting eCall flag or not provided with routing tables 7.12.4.1 General |
| 34 | 7.12.4.2 Route both eCalls and 112/E112 voice calls to a PSAP that is equipped to support the eCall service 7.12.4.3 Route both eCalls and 112/E112 voice calls to a PSAP not equipped to support the eCall service. 7.12.5 PSAP modem failure 7.12.5.1 Before link layer ACK is sent 7.12.5.2 After link layer ACK is sent 7.12.5.3 After application ACK is sent 7.12.6 PSAP network/ICT failure 7.12.7 PSAP application failure |
| 35 | 7.12.8 PSAP operator does not respond 7.12.9 No response if line engaged 7.12.10 MSD not sent 7.12.11 MSD not received |
| 36 | 7.12.12 Audio link not established 7.12.13 Audio link established but subsequently fails 7.12.14 Re-attempt in case of interrupted call 7.12.15 Automatic repeat attempts 7.12.16 IVS NAD does not receive call clear-down 8 Third party services supported eCall (TPS-eCall) 8.1 Overview |
| 37 | 9 Defences against attack (Security provisions) 10 Quality of service requirements 11 Test and conformance requirements 12 Marking, labelling and packaging 13 Declaration of patents and intellectual property |
| 38 | Annex A (normative) Table of timings Table A.1 — Table of timings |
| 40 | Annex B (informative) Summary abstracts of normative referenced documents B.1 Objective B.2 Summary abstracts B.2.1 EN 15722, Intelligent transport systems — ESafety — ECall minimum set of data (MSD) B.2.2 EN ISO 24978, Intelligent transport systems — ITS safety and emergency messages using any available wireless media — Data registry procedures (ISO 24978:2009) B.2.3 WGS84 World Geodetic System 84 (last revised 2004) B.2.4 EN 16072, Intelligent transport systems — eSafety — Pan-European eCall operating requirements |
| 41 | B.2.5 EN 16102, Intelligent transport systems — eSafety — Third party supporting eCall : Operating requirements B.2.6 ETSI/TS 122 101, Universal Mobile Telecommunications System (UMTS); LTE; Service aspects; Service principles (Release 8) |
| 42 | B.2.7 ETSI/TS 124 008, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Mobile radio interface Layer 3 specification; Core network protocols; Stage 3 B.2.8 ETSI/TS 126 267, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); eCall data transfer; In- band modem solution; General description |
| 43 | B.2.9 ETSI/TS 126 268, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); eCall data transfer; In- band modem solution; ANSI-C reference code B.2.10 Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); eCall data transfer; In-band modem solution; Conformance testing B.2.11 Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations and Directive 98/48/EC of the European Parliament and … |
| 44 | B.2.12 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity B.2.13 ETSI/TS 122 003, Digital cellular communications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Circuit Teleservices supported by a Public Land Mobile Network (PLMN) (Teleservice 12/TC12) /E12 B.2.14 ETSI/TS 122 011, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Service accessibility |
| 45 | B.2.15 ETSI/TS 127 007, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); AT command set for user equipment B.2.16 ETSI/TS 122 071, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Location Services (LCS); Service description; Stage 1 |
| 46 | B.2.17 ETSI/TS 122 002, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); Circuit bearer services (BS) supported by a Public Land Mobile Network (PLMN) B.2.18 ETSI/TS 122 004, Digital cellular telecommunications system (Phase 2+); Universal mobile telecommunications system (UMTS); General on supplementary services B.2.19 Directive 2002/22/EC, Directive of the European Parliament and of the Council on universal service and users’ rights relating to electronic communications networks and services (Universal Service Directive) |
| 47 | B.2.20 ETSI/TS 122 001, Digital cellular telecommunications system (Phase 2+); TSG Services and System Aspects; Principles of circuit telecommunication services supported by a Public Land Mobile Network (PLMN) (Release 8) B.2.21 ETSI/TS 123 018, Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); Basic call handling; Technical realization (Release 8) B.2.22 ETSI/TS 102 164, Telecommunications and Internet converged Services and Protocols for Advanced Networking (TISPAN); Emergency location protocols |
| 48 | B.2.23 ETSI/TS 151 010, Digital cellular telecommunications system (Phase 2+); Mobile Station (MS) conformance specification; Part 1: Conformance specification (3GPP TS 51.010-1 version 8.1.0) B.2.24 ETSI/TS 124 123, Universal Mobile Telecommunications System (UMTS); User Equipment (UE) conformance specification; Part 1: Protocol conformance specification (3GPP TS 34.123-1 version 8.6.0) |
| 49 | B.2.25 ETSI 121 133, Universal Mobile Telecommunications System (UMTS); 3G Security; Security Threats and Requirements (3GPP TS 21.133 version 4.1.0) |
| 50 | B.2.26 Directive 2002/22/EC of The European Parliament and of The Council of 7 March 2002 on universal service and users’ rights relating to electronic communications networks and services (Universal Service Directive), amended by Directive 2009/136/… |
| 52 | Annex C (informative) Test system strategies C.1 General C.2 Vehicle and PSAP equipment life cycle |
| 53 | C.3 Laboratory environment Figure C.1 — Example of equipped test laboratory C.4 OEM or third party test systems Figure C.2 — OEM or third party test system |
| 54 | Bibliography |
Related products
-
BS EN 16062:2015 – TC:2020 Edition
Tracked Changes. Intelligent transport systems. ESafety. eCall high level application requirements (HLAP) using GSM/UMTS circuit…
