🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 17670-2:2023

BS EN 17670-2:2023

$198.66

Plastics piping systems for non-pressure underground conveyance of surface water. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) – Specification for road gullies

Published By Publication Date Number of Pages
BSI 2023 52
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document specifies the definitions and requirements for unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) road gullies intended for use in non-pressure underground drains and sewers for surface water having a maximum depth of 4 m from ground level to the lowest point of the internal surface of the road gully. Road gullies complying with this document are intended to be used in pedestrian or vehicular traffic areas outside the building structure. NOTE 1 Products complying with this document can also be used in non-traffic areas. NOTE 2 Road gullies can be subject to national regulation which limit the maximum installation depth and / or local provisions. The installer checks for compliance prior to installation. Road gullies complying with this document are made from a prescribed set of components that are manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) and assembled together. Road gullies complying with this document may be equipped with optional devices (e.g. removable sand or silt bucket, leaf separator etc.), however the performance of these optional devices is not covered within the scope of this document. Road gully components can be manufactured by various methods e.g. extrusion, injection moulding, rotational moulding, low-pressure moulding, blow moulding, thermoforming or fabricated. NOTE 3 Products complying with this document can be installed in underground applications without additional static calculation. NOTE 4 The complete road gully assembly can also include non-plastic items (near surface or surface components for example) which are not covered by this document. NOTE 5 The complete road gully assembly can be supplied with covers, frame covers and gratings complying with the relevant part of EN 124 which are not covered by this document. However, reference is made to this document for geometrical characteristics where applicable. NOTE 6 Road gullies can be site assembled from different components, but can also be manufactured as a single unit. This document covers: – road gullies with or without sand / silt trap; – road gullies with or without water seal preventing odour release; – road gullies where the traffic load will or will not be carried by the complete gully (resp. “Direct loaded gullies” or “Indirect loaded gullies”).

PDF Catalog

PDF Pages PDF Title
2 undefined
8 1 Scope
9 2 Normative references
11 3 Terms and definitions
21 4 Symbols and abbreviations
22 5 Material
25 6 General characteristics
7 Geometrical characteristics
26 8 Mechanical characteristics
28 9 Physical characteristics
29 10 Performance requirements
31 11 Sealing rings
12 Adhesives for PVC-U
13 Gully tops
14 Marking and additional documentation
34 Annex A (normative)Test method for durability
A.1 General
A.2 Test procedure
35 A.3 Material characteristics
38 Annex B (normative)Test method for impact resistance of road gullies or road gully bases
B.1 Test equipment
B.2 Test procedure
39 Annex C (normative)Utilization of reworked material and recyclates
43 Annex D (normative)Test method for structural integrity of road gully bases or assemblies
44 Annex E (normative)Test method for dynamic loading
E.1 General
E.2 Principle
47 E.3 Apparatus (accuracy of test equipment)
E.4 Parallel plates
E.5 Supporting element
E.6 Dimensional measuring device
E.7 Load measuring device
E.8 Test sample
E.9 Conditioning
E.10 Procedure
48 E.11 Requirements
E.12 Background to dynamic test parameters
49 E.13 Test report
50 Annex F (informative)Relationship between system performance and tested characteristics

Related products

BS EN 17670-2:2023
$198.66