BS EN 61167:2011
$215.11
Metal halide lamps. Performance specification
| Published By | Publication Date | Number of Pages |
| BSI | 2011 | 162 |
This International Standard specifies the performance requirements for metal halide lamps for general lighting purposes.
For some of the requirements given in this standard, reference is made to “the relevant lamp data sheet”. For some lamps, these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor.
The requirements of this standard relate only to type testing.
NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturer’s production and being as close to the production centre point values as possible.
It may be expected with the tolerances given in the standard that product manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | English CONTENTS |
| 8 | INTRODUCTION |
| 9 | 1 Scope 2 Normative references |
| 10 | 3 Terms and definitions |
| 12 | 4 Lamp requirements 4.1 General 4.2 Marking 4.3 Dimensions 4.4 Caps 4.5 Starting and warm-up characteristics |
| 13 | 4.6 Electrical characteristics 4.7 Photometric characteristics 4.8 Colour characteristics 4.9 Lumen maintenance and life |
| 14 | 5 Information for ballast, ignitor and luminaire design 6 Data sheets 6.1 General principles of numbering sheets 6.2 Lists of data sheets Tables Table 1 – List of diagrammatic lamp data sheets |
| 26 | Table 2 – List of lamp data sheets |
| 136 | 6.3 List of maximum lamp outline sheets(construction according to IEC 61126) Table 3 – List of maximum lamp outline sheets |
| 139 | Annex A (normative) Method of measuring lamp starting and warm-up characteristics |
| 140 | Figures Figure A.1 – Circuit diagram for measurement of lamp starting and warm-up characteristics |
| 141 | Annex B (normative) Method of measuring electrical and photometrical characteristics(lamps for operation on 50 Hz or 60 Hz supply frequencies) |
| 142 | Table B.1 – Correlated colour temperature and chromaticity co-ordinates x and y |
| 143 | Figure B.1 – Circuit diagram for measurement of lamp characteristics |
| 144 | Figure B.2 – Luminaire simulator for use with double-capped lamps |
| 145 | Annex C (normative) Method of test for lumen maintenance and life |
| 146 | Annex D (informative) Information for luminaire design |
| 147 | Annex E (normative) Method of measuring electrical and photometrical characteristics on low frequency square wave reference ballast Table E.1 – Characteristics of the reference ballast |
| 148 | Figure E.1 – Circuit for lamp measurement under reference conditions |
| 149 | Annex F (normative) Spectral analysis of power ripple: calculation procedurefor amplitude spectrum ratio and guidance |
| 150 | Table F.1 – Settings of the analysing scope |
| 152 | Annex G (informative) Low frequency square wave operation Table G.1 – Requirements for square wave operation |
| 155 | Figure G.1 – DC current component |
| 156 | Figure G.2 – HF ripple and fast Fourier transformation (power curve) Figure G.3 – Measurement of PCR during run-up and steady state |
| 157 | Figure G.4 – Example of a measurement circuit of lamp potential against earth Figure G.5 – Commutation time, deviating waveform |
| 158 | Annex H (informative) Information for ballast design Figure H.1 – Example 1 to ignition scheme according to option (1)(see Annex G and lamp data sheets) Figure H.2 – Example 2 to ignition scheme according to option (1) (see Annex G and lamp data sheets) |
| 159 | Figure H.3 – Example to ignition scheme according to option (2) (see Annex G and lamp data sheets) |
| 160 | Bibliography |
