BS EN 62922:2017
$142.49
Organic light emitting diode (OLED) panels for general lighting. Performance requirements
| Published By | Publication Date | Number of Pages |
| BSI | 2017 | 32 |
IEC 62922:2016 specifies the performance requirements of OLED tiles and panels for use on DC supplies up to 120 V or AC supplies up to 50 V at 50 Hz or 60 Hz for indoor and similar general lighting purposes.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | English CONTENTS |
| 8 | FOREWORD |
| 10 | 1 Scope 2 Normative references 3 Terms and definitions |
| 11 | 4 General statement and test conditions 4.1 General statement 4.2 General test conditions |
| 12 | 4.3 Stabilization 4.3.1 General requirements for stabilization 4.3.2 Current-driven stabilization 4.3.3 Voltage-driven stabilization 5 Marking 5.1 Contents and location |
| 13 | 5.2 Information on reliability of electrical connection 6 Input power 7 Initial photometric characteristics 7.1 General Tables Table 1 – Contents and location of marking |
| 14 | 7.2 Luminous flux 7.3 Luminous efficacy 7.4 Chromaticity coordinates 7.5 Correlated colour temperature (CCT) 7.6 Colour rendering index (CRI) |
| 15 | 7.7 Luminance uniformity 7.7.1 Average luminance (Lav) 7.7.1.1 The initial average luminance shall not deviate from the rated average luminance by more than 10 %. 7.7.1.2 If using an imaging luminance measurement devices (ILMD), the measurement of average luminance (Lav) shall be carried out in perpendicular direction to the light output surface of an OLED panel. The average luminance shall be calculated from a… 7.7.1.3 If using a spot luminance meter, the measurement of average luminance (Lav) shall be carried out in perpendicular direction to the light output surface of an OLED panel. The distance from the edge of the light output surface to the closest mea… 7.7.2 Luminance uniformity (U) 7.8 Luminous intensity distribution |
| 16 | 7.9 Surface chromaticity uniformity 7.10 Angular chromaticity uniformity 8 Maintained photometric characteristics |
| 17 | 9 Reliability 9.1 High temperature – high humidity operation 9.2 High temperature – high humidity storage 9.3 Reliability of connection |
| 18 | 10 Information for controlgear design |
| 19 | Annexes Annex A (informative) Use of regional standards |
| 20 | Annex B (informative) Measuring method of angular chromaticity uniformity Table B.1 – Chromaticity coordinates for all viewing angles between 0° and 80° in 5° steps |
| 21 | Table B.2 – Colour difference between all chromaticity coordinate pairs |
| 22 | Annex C (normative) Measuring method for luminous flux C.1 General C.2 Integrating sphere measurements C.2.1 Integrating sphere methods and installation position C.2.2 Size of the integrating sphere Figures Figure C.1 – 4π geometry (left), 2π geometry sphere (centre) and 2π geometry hemisphere (right) |
| 23 | C.3 Goniophotometric measurements |
| 24 | Annex D (informative) Tests of robustness of terminations and connectors D.1 General D.2 Wire terminations and pin type connectors D.2.1 General D.2.2 Tensile test D.2.3 Bending test D.2.4 Torsion test D.3 Flexible flat terminations D.3.1 General |
| 25 | D.3.2 Peel test A D.3.3 Peel test B D.4 Soldering Figure D.1 – Schematic diagram of peel test A |
| 26 | Annex E (informative) Information for controlgear design E.1 General E.2 Operation E.3 Characteristics of the driver output current Figure E.1 – Voltage and luminance behaviour at constant current operation |
| 27 | E.4 Characteristics of the driver output voltage E.5 Dimming E.6 Short-circuit protection |
| 28 | Annex F (informative) Information for luminaire design |
| 29 | Bibliography |
