🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 747-2:2012+A1:2015

BS EN 747-2:2012+A1:2015

$142.49

Furniture. Bunk beds and high beds – Test methods

Published By Publication Date Number of Pages
BSI 2015 24
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This European Standard specifies test methods for the safety, strength and durability of bunk beds and high beds for domestic and non-domestic use. The loads and forces in the strength and durability tests apply to beds with an internal length greater than 140 cm and a maximum bed base width of 120 cm.

The tests are designed to be applied to a bed that is fully assembled and ready for use. The applicable safety requirements are given in EN 747‑1 .

PDF Catalog

PDF Pages PDF Title
4 Contents Page
5 Foreword
6 Introduction
7 1 Scope
2 Normative references
3 General test conditions
3.1 Preliminary preparation
8 3.2 Application of forces
3.3 Tolerances
4 Test equipment
4.1 General
4.2 Measuring cones
9 Figure 1 — Examples of measuring cones
4.3 Bed base impactor
4.3.1 Bed base impactor (see Figure 2)
4.3.2 Springs
Figure 2 — Bed base impactor
10 4.3.3 Striking surface
4.4 Loading pads
4.4.1 Rigid and circular object, 200 mm in diameter, the face of which has a convex spherical curvature of a 300 mm radius with a 12 mm front edge radius (see Figure 3).
Figure 3 — Loading pad
4.4.2 Rigid and cylindrical object, 100 mm in diameter, having a flat, smooth, hard surface and rounded edge with a radius of 12 mm.
4.5 Test mattress
11 4.6 Test mass
4.7 Stops
4.8 Floor surface
4.9 Tread impactor
Figure 4 — Tread impactor
12 4.10 Template for V-shaped openings
Figure 5 — V and irregular shaped openings template”
5 Test procedures
5.1 Inspection before testing
5.2 Inspection of product
5.3 Measurements
5.3.1 Holes, gaps and openings
13 Table 1 — Cones and forces
5.3.2 V and irregular shaped holes, gaps and openings
Figure 6 — Method of insertion of portion B
14 Figure 7 — Method of insertion of portion B
15 Figure 8 — Method of insertion of portion A”
5.4 Strength tests
5.4.1 Positioning of the bed
5.4.2 Static load on safety barriers
16 5.4.3 Upwards and downwards static load on bed base
5.4.4 Impact test on bed base
17 !Figure 9″ — Bed base impact positions
5.4.5 Durability test on bed base
!Figure 10″ — Durability of bed base loading positions
5.5 Durability test of frame and fastenings
18 !Figure 11″ — Durability of frame — Application of load and forces
5.6 Ladders or other means of access
5.6.1 Vertical static load on treads
5.6.2 Horizontal static loads on treads
19 !Figure 12″ — Vertical and horizontal static loads on treads
5.6.3 Durability of treads
5.6.4 Tread impact test
20 !Figure 13″ — Tread impact test
5.7 Stability test
5.8 Fastening of the upper bed to the lower bed
6 Test report

Related products

BS EN 747-2:2012+A1:2015
$142.49