Shopping Cart

No products in the cart.

BS EN IEC 60974-10:2021:2022 Edition

$189.07

Arc welding equipment – Electromagnetic compatibility (EMC) requirements

Published By Publication Date Number of Pages
BSI 2022 48
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

IEC 60974-10:2014 specifies a) applicable standards and test methods for radio-frequency (RF) emissions; b) applicable standards and test methods for harmonic current emission, voltage fluctuations and flicker; c) immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. This standard is applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilizing devices. This third edition cancels and replaces the second edition published in 2007 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: – inclusion of optional use of a decoupling network and a load outside the test chamber; – inclusion of an alternative test setup for portable equipment; – inclusion of test conditions for complex controls, liquid cooling systems and arc striking and stabilizing devices; – update of the applicable limits related to the updated reference to CISPR 11; – exclusion of the use of narrow band relaxations for RF emission limits; – update of the applicable limits for harmonics and flicker and inclusion of flow-charts related to the updated reference to IEC 61000-3-11 and IEC 61000-3-12; – update of the requirements for voltage dips related to the updated reference to IEC 61000-4-11 and IEC 61000-4-34; – update of the informative annex for installation and use; – inclusion of symbols to indicate the RF equipment class and restrictions for use.

PDF Catalog

PDF Pages PDF Title
2 undefined
7 Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
11 International standard (Bilingual)
12 English
CONTENTS
15 FOREWORD
17 1 Scope
2 Normative references
19 3 Terms and definitions
20 Figures
Figure 1 ā€“ Examples of ports
21 4 General test requirements
4.1 Test conditions
4.2 Measuring instruments
22 4.3 Artificial mains network
4.4 Voltage probe
4.5 Antennas
4.6 Coupling/decoupling network (CDN)
5 Test set-up for emission and immunity
5.1 General
23 Figure 2 ā€“ Test set-up 1 for arc welding equipment
24 Figure 3 ā€“ Test set-up 2 for portable arc welding equipment
25 5.2 Load
Figure 4 ā€“ Top view of test set-up as shown in Figure 2
26 5.3 Ancillary equipment
5.3.1 General requirements
5.3.2 Wire feeders
5.3.3 Remote controls
5.3.4 Arc striking and stabilizing devices
27 5.3.5 Liquid cooling systems
6 Emission tests
6.1 Classification for RF emission tests
6.1.1 Class A equipment
6.1.2 Class B equipment
6.2 Test conditions
6.2.1 Welding power source
28 6.2.2 Load voltages
29 6.2.3 Wire feeders
6.2.4 Ancillary equipment
6.3 Emission limits
6.3.1 General
6.3.2 Mains terminal disturbance voltage
30 Tables
Table 1 ā€“ Mains terminal disturbance voltage limits, idle state
31 6.3.3 Conducted emissions at signal, control and measurement ports
6.3.4 Output current ripple
Table 2 ā€“ Mains terminal disturbance voltage limits, load conditions
32 6.3.5 Electromagnetic radiation disturbance
Table 3 ā€“ Output current ripple limits for Class B arc welding power sources
Table 4 ā€“ Electromagnetic radiation disturbance ā€“ Idle state
33 6.3.6 Harmonics, voltage fluctuations and flicker
Table 5 ā€“ Electromagnetic radiation disturbance ā€“ Loaded state
34 Figure 5 ā€“ Overview of harmonic requirements for supply current I1max up to 75 A
Figure 6 ā€“ Overview of flicker requirements
35 7 Immunity tests
7.1 Classification for immunity tests
7.1.1 Applicability of tests
7.1.2 Category 1 equipment
7.1.3 Category 2 equipment
7.2 Test conditions
7.3 Immunity performance criteria
7.3.1 Performance criterion A
36 7.3.2 Performance criterion B
7.3.3 Performance criterion C
7.4 Immunity levels
Table 6 ā€“ Immunity levels ā€“ Enclosure
37 Table 7 ā€“ Immunity levels ā€“ AC input power port
38 8 Documentation for the purchaser/user
Table 8 ā€“ Immunity levels ā€“ Ports for process, signalling, measurement and control
40 Annexes
Annex A (informative) Installation and use
A.1 General
A.2 Assessment of area
A.3 Assessment of welding installation
41 A.4 Mitigation measures
42 Annex B (informative) Limits
B.1 General
B.2 Conducted disturbance voltage limits
B.3 Output current ripple limit
B.4 Radiated disturbance limits
B.5 Output current ripple limits
43 Annex C (informative) Symbols
Table C.1 ā€“ Symbols to describe EMC properties
44 Annex D (normative) Battery powered equipment
D.1 General
D.2 Additional emission requirements
D.3 Additional immunity requirements
45 Annex E (normative) Equipment containing radio devices
E.1 General
E.2 Additional emission requirements
E.3 Additional immunity requirements
46 Bibliography
BS EN IEC 60974-10:2021
$189.07