BS EN IEC 61784-5-6:2018:2019 Edition
$198.66
Industrial communication networks. Profiles – Installation of fieldbuses. Installation profiles for CPF 6
| Published By | Publication Date | Number of Pages |
| BSI | 2019 | 58 |
This part of IEC 61784-5 specifies the installation profiles for CPF 6 (INTERBUS)1.
The installation profiles are specified in the annexes. These annexes are read in conjunction with IEC 61918:2018.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 5 | Annex ZA(normative)Normative references to international publicationswith their corresponding European publications |
| 7 | CONTENTS |
| 12 | FOREWORD |
| 14 | INTRODUCTION Figures Figure 1 – Standards relationships |
| 15 | 1 Scope 2 Normative references 3 Terms, definitions and abbreviated terms 4 CPF 6: Overview of installation profiles |
| 16 | 5 Installation profile conventions 6 Conformance to installation profiles |
| 18 | Annex A (normative)CPF 6 Type 8 network specific installation profile A.1 Installation profile scope A.2 Normative references |
| 19 | A.3 Installation profile terms, definitions, and abbreviated terms A.3.1 Terms and definitions A.3.2 Abbreviated terms |
| 20 | A.3.3 Conventions for installation profiles A.4 Installation planning A.4.1 General A.4.2 Planning requirements |
| 21 | A.4.3 Network capabilities |
| 22 | Figure A.1 – Type 8 network structure example |
| 23 | Figure A.2 – Example of a Type 8 network configuration |
| 24 | Tables Table A.1 – Basic network characteristics for balanced cabling not based on Ethernet |
| 25 | Table A.2 – Network characteristics for optical fibre cabling |
| 26 | A.4.4 Selection and use of cabling components Table A.3 – Information relevant to balanced cable: fixed cables |
| 27 | Table A.4 – Information relevant to balanced cable: cords |
| 29 | Table A.5 – Remote bus fibre optic cable length |
| 30 | Table A.6 – Connectors for copper cabling CPs not based on Ethernet Table A.7 – Optical fibre connecting hardware |
| 31 | Table A.8 – Relationship between FOC and fibre types (Type 8 networks) |
| 32 | Table A.9 – Colour code for balanced cables used by Type 8 networks |
| 34 | A.4.5 Cabling planning documentation A.4.6 Verification of cabling planning specification A.5 Installation implementation A.5.1 General requirements A.5.2 Cable installation |
| 35 | Table A.10 – Parameters for balanced cables Table A.11 – Parameters for silica optical fibre cables Table A.12 – Parameters for POF optical fibre cables |
| 36 | Table A.13 – Parameters for hard clad silica optical fibre cables |
| 37 | A.5.3 Connector installation Figure A.3 – SubD connector pin assignment Figure A.4 – M23 circular connector pin assignment |
| 38 | A.5.4 Terminator installation A.5.5 Device installation A.5.6 Coding and labelling A.5.7 Earthing and bonding of equipment and devices and shield cabling Figure A.5 – M12 circular connector pin assignment Figure A.6 – Terminal connector at the device Table A.14 – Pin assignment of the terminal connector |
| 39 | A.5.8 As-implemented cabling documentation A.6 Installation verification and installation acceptance test A.6.1 General A.6.2 Installation verification |
| 40 | A.6.3 Installation acceptance test A.7 Installation administration A.8 Installation maintenance and installation troubleshooting |
| 42 | Annex B (normative)CPF 6 Ethernet network specific installation profile B.1 Installation profile scope B.2 Normative references |
| 43 | B.3 Installation profile terms, definitions, and abbreviated terms B.3.1 Terms and definitions B.3.2 Abbreviated terms B.3.3 Conventions for installation profiles B.4 Installation planning B.4.1 General B.4.2 Planning requirements |
| 44 | B.4.3 Network capabilities |
| 45 | Table B.1 – Network characteristics for balanced cabling based on Ethernet |
| 46 | Table B.2 – Network characteristics for optical fibre cabling |
| 47 | B.4.4 Selection and use of cabling components Table B.3 – Information relevant to copper cable: fixed cables |
| 48 | Table B.4 – Information relevant to copper cable: cords |
| 49 | Table B.5 – Information relevant to optical fibre cables |
| 50 | Table B.6 – Connectors for balanced cabling CPs based on Ethernet Table B.7 – Connectors for copper cabling CPs not based on Ethernet |
| 51 | Table B.8 – Optical fibre connecting hardware Table B.9 – Relationship between FOC and fibre types (CP 6/2 Ethernet network) |
| 53 | B.4.5 Cabling planning documentation B.4.6 Verification of cabling planning specification B.5 Installation implementation B.5.1 General requirements B.5.2 Cable installation Table B.10 – Parameters for balanced cables |
| 54 | Table B.11 – Parameters for silica optical fibre cables Table B.12 – Parameters for POF optical fibre cables Table B.13 – Parameters for hard clad silica optical fibre cables |
| 55 | B.5.3 Connector installation B.5.4 Terminator installation B.5.5 Device installation B.5.6 Coding and labelling B.5.7 Earthing and bonding of equipment and devices and shield cabling Figure B.1 – Terminal connector at the device |
| 56 | B.5.8 As-implemented cabling documentation B.6 Installation verification and installation acceptance test B.6.1 General B.6.2 Installation verification B.6.3 Installation acceptance test B.7 Installation administration B.8 Installation maintenance and installation troubleshooting |
| 57 | Bibliography |
Related products
-
BS EN IEC 61784-5-6:2018 – TC:2020 Edition
Tracked Changes. Industrial communication networks. Profiles – Installation of fieldbuses. Installation profiles for CPF 6…
-
BS EN IEC 61784-5-6:2018:2019 Edition
Industrial communication networks. Profiles – Installation of fieldbuses. Installation profiles for CPF 6 Published By…
