🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN IEC 62196-1:2022 – TC:2023 Edition

BS EN IEC 62196-1:2022 – TC:2023 Edition

$280.87

Tracked Changes. Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles – General requirements

Published By Publication Date Number of Pages
BSI 2023 249
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This part of IEC 62196 is applicable to EV plugs, EV socket-outlets, vehicle connectors, vehicle inlets, herein referred to as “accessories”, and to cable assemblies for electric vehicles (EV) intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding: – 690 V AC 50 Hz to 60 Hz, at a rated current not exceeding 250 A; – 1 500 V DC at a rated current not exceeding 800 A. These accessories and cable assemblies are intended to be installed by instructed persons (IEV 195-04-02) or skilled persons (IEV 195-04-01) only. These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851 (all parts), which operate at different voltages and frequencies, and which can include extra-low voltage and communication signals. These accessories and cable assemblies are intended to be used at an ambient temperature between −30 °C and +40 °C. NOTE 1 In some countries, other requirements can apply. NOTE 2 In the following country, −35 °C applies: SE. NOTE 3 The manufacturer can enlarge the temperature range on the condition that the specified range information is provided. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this document are intended for use in electric vehicle supply equipment in accordance with IEC 61851 (all parts). This document does not apply to standard plug and socket-outlets used for mode 1 and mode 2 according to IEC 61851-1:2017, 6.2. NOTE 4 In the following countries, mode 1 is not allowed: UK, US, CA, SG.

PDF Catalog

PDF Pages PDF Title
145 undefined
151 Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
154 English
CONTENTS
158 FOREWORD
160 INTRODUCTION
161 1 Scope
2 Normative references
163 3 Terms and definitions
164 Figures
Figure 1 – Diagram showing the use of the accessories
168 Figure 2 – Lug terminals
Figure 3 – Mantle terminals
169 Figure 4 – Pillar terminals
170 Figure 5 – Saddle terminals
171 Figure 6 – Screw-type terminals
172 Figure 7 – Stud terminals
173 4 General
4.1 General requirements
4.2 Components
4.2.1 Ratings
4.2.2 Mechanical assembly
4.2.3 Current-carrying parts of incorporated components
4.2.4 Electrical connections
174 4.3 General notes on tests
175 5 Ratings
5.1 Preferred rated operating voltage ranges
5.2 Preferred rated currents
5.2.1 General
176 5.2.2 Rated current for signal or control purposes
5.2.3 Accessories not suitable for making and breaking an electrical circuit under load
5.2.4 Accessories suitable for, or not suitable for, making and breaking an electrical circuit under load
6 Connection between the power supply and the electric vehicle
6.1 Interfaces
6.2 Basic interface
6.3 DC interface
6.4 Combined interface
177 7 Classification of accessories
7.1 According to purpose
7.2 According to the method of connecting the conductors
7.3 According to serviceability
7.4 According to electrical operation
7.5 According to interface
7.6 According to locking facilities
7.7 According to interlock facilities
7.8 According to the presence of shutter(s)
8 Marking
180 9 Dimensions
Figure 8 – Test piston
181 10 Protection against electric shock
10.1 General
10.2 Accessories with shutters
183 Figure 9 – Gauge “A” for checking shutters
184 10.3 Contact sequencing and order of contact insertion and withdrawal
Figure 10 – Gauge “B” for checking shutters
185 10.4 Misassembly
11 Size and colour of protective earthing and neutral conductors
186 12 Provisions for earthing
Tables
Table 1 – Size for conductors
187 Table 2 – Short-time test currents
188 13 Terminals
13.1 Common requirements
190 13.2 Screw type terminals
191 Figure 11 – Gauges for testing insertability of round unprepared conductor shaving the maximum specified cross-section
192 13.3 Mechanical tests on terminals
193 Figure 12 – Equipment test arrangement
194 Table 3 – Values for flexing under mechanical load test
195 14 Interlocks
14.1 Accessories with interlock
Table 4 – Value for terminal pull test
198 Figure 13 – Apparatus for checking the withdrawal force
199 Figure 14 – Verification of the latching device
Table 5 – Withdrawal force with respect to ratings
200 14.2 Accessories with integral switching device
14.3 Control circuit devices and switching elements
14.4 Pilot contacts and auxiliary circuits
15 Resistance to ageing of rubber and thermoplastic material
201 16 General construction
202 Table 6 – Cable length used to determine pull force on retaining means
205 17 Construction of EV socket-outlets – General
18 Construction of EV plugs and vehicle connectors
206 19 Construction of vehicle inlets
20 Degrees of protection
208 21 Insulation resistance and dielectric strength
209 22 Breaking capacity
Table 7 – Test voltage for dielectric strength test
211 Figure 15 – Circuit diagrams for breaking capacity and normal operation tests
212 23 Normal operation
23.1 Mechanical, electrical, and thermal stresses and contaminants
23.2 Load endurance test
Table 8 – Breaking capacity
213 23.3 No-load endurance test
Table 9 – Normal operation
214 23.4 Lid springs
24 Temperature rise
215 Table 10 – Test current and nominal cross-sectional areas of copper conductors for temperature rise test
216 25 Flexible cables and their connection
25.1 Strain relief
25.2 Requirements for EV plugs and vehicle connectors
25.2.1 Non-rewirable EV plugs and vehicle connectors
25.2.2 Rewirable EV plugs and vehicle connectors
Figure 16 – Points of measurement
217 25.3 EV plugs and vehicle connectors provided with a flexible cable
218 Figure 17 – Apparatus for testing the cable anchorage
219 26 Mechanical strength
26.1 General
Table 11 – Pull force and torque test values for cable anchorage
Table 12 – Summary of mechanical tests
220 26.2 Ball impact
Figure 18 – Ball impact test
221 26.3 Drop test
Table 13 – Impact energy for ball impact test
222 26.4 Flexing test
Figure 19 – Arrangement for mechanical strength testfor EV plugs and vehicle connectors
223 Table 14 – Mechanical load flexing test
224 26.5 Cable gland test
Figure 20 – Apparatus for flexing test
225 26.6 Shutters
26.7 Insulated end caps
26.7.1 General
Table 15 – Torque test values for glands
226 26.7.2 Insulated end caps – Change of temperature test
26.7.3 Insulated end caps – Pull test
27 Screws, current-carrying parts and connections
Table 16 – Pulling force on insulated end caps
227 Table 17 – Tightening torque for verificationof mechanical strength of screw-type terminals
229 28 Creepage distances, clearances and distances through sealing compound
230 29 Resistance to heat and to fire
231 30 Corrosion and resistance to rusting
232 31 Conditional short-circuit current
31.1 General
31.2 Ratings and test conditions
233 31.3 Test circuit
234 Figure 21 – Diagram of the test circuit for the verification of short-circuit current withstand of two-pole equipment on a single-phase AC or DC
235 Figure 22 – Diagram of the test circuit for the verification of short-circuit current withstand of three-pole equipment
236 31.4 Calibration
31.5 Test procedure
Figure 23 – Diagram of the test circuit for the verification ofshort-circuit current withstand of four-pole equipment
237 31.6 Behaviour of the equipment under test
31.7 Acceptance conditions
32 Electromagnetic compatibility
32.1 Immunity
32.2 Emission
33 Vehicle drive over
238 34 Thermal cycling
34.1 General
34.2 Initial temperature rise test
34.3 Thermal cycling test
34.4 Final temperature rise test
239 35 Humidity exposure
35.1 General
35.2 Initial temperature rise test
35.3 Humidity test
35.4 Final temperature rise test
36 Misalignment
36.1 General
240 36.2 Samples
36.3 Misalignment test
241 Figure 24 – Overview of the mechanical load test
Figure 25 – Application of external mechanical load (mounted according to Figure 24)
242 37 Contact endurance test
37.1 Equipment
Figure 26 – Temperature rise criteria under external mechanical load
Figure 27 – Forced-air circulating oven
243 37.2 Test sequence
244 37.3 Compliance
Figure 28 – Thermal cycling
245 Figure 29 – Pass/fail based on temperature rise criteria
246 Bibliography

Related products

BS EN IEC 62196-1:2022 - TC
$280.87