BS ISO 21111-3:2020
$215.11
Road vehicles. In-vehicle Ethernet – Optical 1-Gbit/s physical entity requirements and conformance test plan
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 198 |
This document provides supplemental specifications to a physical layer capable of transmitting 1 Gbit/s over plastic optical fibre compliant with ISO/IEC/IEEE 8802-3:2017/Amd 9:2018, with specific application to communications inside road vehicles.
Additionally, there is a test plan specified for conformance testing. The test plan includes test cases to assure compliance of an IUT with the functionality specified in this document.
ISO/IEC/IEEE 8802-3:2017/Amd 9:2018 is considered indispensable for the application of this document.
The supplemental specifications include wake-up and synchronised link sleep functionality. The specification includes the sublayers, service interfaces, and state diagrams that support the functionality. The supplemental specifications are collected in protocol implementation conformance statement (PICS).
The requirements specified in ISO/IEC/IEEE 8802-3:2017/Amd 9:2018 and in this document constitute the complete PICS that specifies the GEPOF physical entity functionality.
The optical component requirements and test methods for optical 1-Gbit/s transmission of in-vehicle Ethernet are not within the scope of this document.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 8 | Foreword |
| 9 | Introduction |
| 11 | 1 Scope 2 Normative references |
| 12 | 3 Terms and definitions 4 Abbreviated terms |
| 14 | 5 Wake-up and synchronised link sleep functionality 5.1 General |
| 15 | 5.2 PHY service interface for a GEPOF entity |
| 17 | 5.3 Neighbour PHY service interface for a GEPOF entity |
| 19 | 5.4 Conciliation service interface 5.4.1 General |
| 21 | 5.4.2 CON_WakeUpSleepPacket.request 5.4.3 CON_WakeUpSleepPacket.indication |
| 22 | 5.4.4 CON_WakeUpSleepPacketACK.indication 5.4.5 CON_SignalDetected.indication 5.4.6 CON_OAMActive.indication |
| 23 | 5.5 FFME service interface 5.5.1 General |
| 25 | 5.5.2 FFME_PowerDownStatus.request 5.5.3 FFME_PowerDownStatus.indication 5.5.4 FFME_WakeUp.indication |
| 26 | 5.6 802-3bv service interface 5.6.1 General |
| 28 | 5.6.2 802-3bv_PowerDownStatus.request 5.6.3 802-3bv_RXDETECT.indication 5.7 WUSME Sublayer 5.7.1 General 5.7.2 WUSME wake-up functionality |
| 31 | 5.7.3 WUSME synchronised link sleep functionality |
| 33 | 5.7.4 PHY_SleepStatus.indication generation 5.8 FFME sublayer 5.8.1 General 5.8.2 FFME power state functionality |
| 36 | 5.9 Conciliation sublayer 5.9.1 General 5.9.2 Conciliation sublayer variables 5.9.3 CRC16 computation |
| 37 | 5.9.4 Generating ISO/IEC/IEEE 8802-3:2017/Amd 9:2018, Clause 45 stimuli from CON_WakeUpSleepPacket.request 5.9.5 Generating CON_WakeUpSleepPacket.indication from ISO/IEC/IEEE 8802-3:2017/Amd 9:2018, Clause 45 stimuli |
| 38 | 5.9.6 Generating CON_WakeUpSleepPacketACK.indication from ISO/IEC/IEEE 8802-3:2017/Amd 9:2018, Clause 45 stimuli 5.9.7 Generating CON_SignalDetected.indication from ISO/IEC/IEEE 8802-3:2017/Amd 9:2018, Clause 45 stimuli 5.9.8 Conciliation sublayer constants |
| 39 | 6 PICS proforma 6.1 General 6.2 Major capabilities/options 6.3 Wake-up and synchronised link sleep PICS items |
| 40 | 7 Test plan 7.1 Test plan scope 7.2 Test plan architecture |
| 42 | 7.3 Test plan organization 7.4 Test case sections |
| 43 | 7.5 Test case reference tables 7.5.1 Block 1: test mode and loopback test cases |
| 44 | 7.5.2 Block 2: PCS, PMA, PMD and MDI test cases |
| 47 | 7.5.3 Block 3. EEE, OAM and wake-up and synchronised link sleep test cases |
| 48 | 7.6 Test setups 7.6.1 General |
| 52 | 7.6.2 Test setup 1: TS_BASE |
| 53 | 7.6.3 Test setup 2: TS_EXTEND |
| 54 | 7.6.4 Test setup 3: TS_SIGPOW 7.6.5 Test setup 4: TS_AOPTX 7.6.6 Test setup 5: TS_ER 7.6.7 Test setup 6: TS_CW 7.6.8 Test setup 7: TS_SW 7.6.9 Test setup 8: TS_RT_FT 7.6.10 Test setup 9: TS_OS 7.6.11 Test setup 10: TS_NOD_POD |
| 55 | 7.6.12 Test setup 11: TS_DIST 7.6.13 Test setup 12: TS_RIN 7.6.14 Test setup 13: TS_MPD 7.6.15 Test setup 14: TS_TJ 7.6.16 Test setup 15: TS_2LP 7.6.17 Test setup 16: TS_AOPRX |
| 56 | 7.6.18 Test setup 17: TS_LOOP |
| 57 | 7.7 Block 1 test cases: test modes and loopbacks 7.7.1 General 7.7.2 LBT_1: Loopback control |
| 58 | 7.7.3 LBT_2: GMII loopback |
| 60 | 7.7.4 LBT_3: PMD loopback |
| 62 | 7.7.5 TMT_1: Test mode configuration general |
| 63 | 7.7.6 TMT_2: Test mode 1 transmission |
| 65 | 7.7.7 TMT_4: Test mode 2 transmission |
| 66 | 7.7.8 TMT_5: Test mode 3 transmission |
| 67 | 7.7.9 TMT_6: Test mode 4 transmission |
| 68 | 7.7.10 TMT_7: Test mode 5 transmission |
| 69 | 7.7.11 TMT_8: Test mode 6 transmission |
| 70 | 7.7.12 TMT_3: Test mode 1 reception |
| 72 | 7.7.13 LBT_4: Line loopback |
| 74 | 7.8 Block 2 test cases: Mandatory functionality 7.8.1 General 7.8.2 PCST_1: PCS transmission signalling |
| 75 | 7.8.3 PCST_2: PCS transmission PHD |
| 79 | 7.8.4 PCST_3: Transmission PCS payload data |
| 82 | 7.8.5 PCST_4: PCS reception header and payload data |
| 83 | 7.8.6 PCST_5: PCS transmission alignment |
| 85 | 7.8.7 PCST_6: PCS reception alignment |
| 87 | 7.8.8 PMAT_1: Transmission PMA power scaling test |
| 90 | 7.8.9 PMAT_2: THP transmission |
| 92 | 7.8.10 PMAT_3: State diagrams ‒ Transmit PHD commit point |
| 94 | 7.8.11 PMAT_4: State diagrams ‒ Receive PHD commit point |
| 96 | 7.8.12 PMAT_5: State diagrams ‒ TX control |
| 98 | 7.8.13 PMAT_6: State diagrams ‒ RX control |
| 102 | 7.8.14 PMAT_7: State diagrams ‒ Link monitor |
| 106 | 7.8.15 PMAT_8: State diagrams ‒ PHD monitor |
| 110 | 7.8.16 PMAT_9: State diagrams ‒ Adaptive THP TX |
| 113 | 7.8.17 PMAT_10: State diagrams ‒ Adaptive THP request |
| 116 | 7.8.18 PMAT_11: State diagrams ‒ Quality monitor state diagram |
| 120 | 7.8.19 PMAT_12: Synchronisation |
| 122 | 7.8.20 PMAT_13: Equalization and BER measurement |
| 124 | 7.8.21 PMDT_1: PMD transmit function ‒ Electrical to optical |
| 126 | 7.8.22 PMDT_2: PMD transmit function ‒ Power control |
| 127 | 7.8.23 PMDT_3: PMD receive function ‒ Optical to electrical |
| 129 | 7.8.24 PMDT_4: PMD signal detect function |
| 130 | 7.8.25 PMD_MDIT_1: Transmitter optical specifications ‒ AOP |
| 131 | 7.8.26 PMD_MDIT_2: Transmitter optical specifications ‒ ER |
| 132 | 7.8.27 PMD_MDIT_3: Transmitter optical specifications ‒ Centre wavelength |
| 133 | 7.8.28 PMD_MDIT_4: Transmitter optical specifications ‒ Spectral width 7.8.29 PMD_MDIT_5: Transmitter optical specifications ‒ Rise time |
| 134 | 7.8.30 PMD_MDIT_6: Transmitter optical specifications ‒ Fall time |
| 135 | 7.8.31 PMD_MDIT_7: Transmitter optical specifications ‒ Signal overshoot |
| 136 | 7.8.32 PMD_MDIT_8: Transmitter optical specifications ‒ Positive output droop |
| 137 | 7.8.33 PMD_MDIT_9: Transmitter optical specifications ‒ Negative output droop 7.8.34 PMD_MDIT_10: Transmitter optical specifications ‒ Signal distortion |
| 138 | 7.8.35 PMD_MDIT_11: Transmitter optical specifications ‒ Relative intensity noise |
| 139 | 7.8.36 PMD_MDIT_12: Transmitter optical specifications ‒ Transmitter off transition time |
| 142 | 7.8.37 PMD_MDIT_13: Transmitter optical specifications ‒ Transmitter on transition time |
| 144 | 7.8.38 PMD_MDIT_14: Transmitter optical specifications ‒ Modal power distribution |
| 145 | 7.8.39 PMD_MDIT_15: Transmitter optical specifications ‒ Timing jitter |
| 146 | 7.8.40 PMD_MDIT_16: Receiver optical specifications ‒ AOP for a minimum BER |
| 147 | 7.8.41 PMD_MDIT_17: Receiver optical specifications ‒ Damage threshold power |
| 148 | 7.8.42 DLYT_1: Transmission plus reception delay |
| 149 | 7.9 Block 3 test cases: Optional functionality 7.9.1 General |
| 150 | 7.9.2 EEET_1: Enter to LPI mode transmit operation |
| 153 | 7.9.3 EEET_2: EEE capability exchange |
| 155 | 7.9.4 EEET_3: Loop test for LPI mode |
| 158 | 7.9.5 EEET_4: Resume from LPI mode transmit operation |
| 160 | 7.9.6 OAMT_1: State diagrams ‒ OAM transmit control |
| 165 | 7.9.7 OAMT_2: State diagrams ‒ OAM receive control |
| 169 | 7.9.8 OAMT_3: Loop test for OAMPDU transmission and reception |
| 175 | 7.9.9 WUST_1: WUSME synchronised link sleep state diagram ‒ Synchronised link sleep ACK |
| 179 | 7.9.10 WUST_2: WUSME synchronised link sleep state diagram ‒ SLEEP_ACK packet reception |
| 183 | 7.9.11 WUST_3: WUSME synchronised link sleep state diagram ‒ SLEEP packet reception |
| 186 | 7.9.12 WUST_4: WUSME synchronised link sleep state diagram ‒ Sleep rejection |
| 192 | 7.9.13 WUST_5: WUSME wake-up state diagram |
| 196 | Bibliography |
