BS ISO 9413:2019
$215.11
Tyre valves. Dimensions and designation
| Published By | Publication Date | Number of Pages |
| BSI | 2019 | 116 |
This document defines the essential dimensions and the designation of tube valves and tubeless valves.
Annex B gives the correspondence between ISO designations and the designations established by:
-
TRA (Tire and Rim Association Inc.);
-
ETRTO (European Tyre and Rim Technical Organisation);
-
JATMA (The Japan Automotive Tyre Manufacturer’s Association, Inc.).
In the remainder of this document, all the dimensions are given at their nominal value except in cases where the tolerances are indicated.
The threaded length of valve stems for which no thread length is specified is the maximum possible length.
NOTE
The drawings for valves are not all at the same scale.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 7 | Foreword |
| 9 | 1 Scope 2 Normative references 3 Terms and definitions 4 Valves and valve componente for tyres ― Identification system |
| 10 | 5 Tubeless valves only 5.1 Snap-in valves 5.1.1 Valve hole  |
| 11 | 5.1.2 Valve hole  |
| 12 | 5.2 Clamp-in valves 5.2.1 Clamp-in valves with O-ring |
| 25 | 5.2.2 Clamp-in valves with grommet |
| 38 | 6 Valves for tubes only 6.1 Rubber‑covered valves 6.1.1 Valve hole  |
| 39 | 6.1.2 Valve hole  |
| 40 | 6.1.3 Valve hole  |
| 46 | 6.2 Rubber‑base valves 6.2.1 Valve hole 6,2 |
| 48 | 6.2.2 Valve hole  |
| 50 | 6.2.3 Rim slot  and  |
| 53 | 6.2.4 Valve hole  |
| 54 | 6.2.5 Valve hole  |
| 55 | 6.3 Rubber semi‑covered‑base valve — Valve hole  or  |
| 56 | 6.4 Screw-on universal valves — Rim slots  and  |
| 62 | 6.5 Large‑bore valves — Rim slot  |
| 65 | 6.6 Metal‑base valve 6.6.1 Valve hole 6,2 |
| 66 | 6.6.2 Valve hole 8,3 |
| 68 | 7 Spuds, valve bodies and adaptors 7.1 Rubber spuds 7.1.1 Spuds for screw-on universal valves — Rim slots  and  |
| 69 | 7.1.2 Rubber‑covered air/liquid spuds — Valve hole  |
| 70 | 7.1.3 Screw-on large‑bore spuds — Valve hole  and rim slot  mm 7.2 Clamp-in spuds 7.2.1 Air/liquid large‑bore spud — Valve hole  |
| 72 | 7.2.2 Valve hole  |
| 74 | 7.3 Valve body and core housing 7.3.1 Tubeless and tube‑type core housing for spuds with valve hole  |
| 75 | 7.3.2 Large and super‑large‑bore valve body for spuds with valve hole  |
| 81 | 7.4 Adaptors 7.4.1 Straight adaptor |
| 82 | 7.4.2 Bent adaptor |
| 83 | 8 Valve components 8.1 O-rings 8.2 Ring washers |
| 84 | 8.3 Hex nuts |
| 86 | 8.4 Knurled nuts, hex nuts, screw |
| 89 | 8.5 Rubber grommets |
| 91 | 8.6 Valve caps |
| 96 | 8.7 Valve core 8.7.1 For ISO core chamber No. 1, No. 3 (short core only) and No. 4 (short core only) |
| 97 | 8.7.2 For ISO core chamber No. 2 |
| 98 | Annex A (normative) Valves and valve components for tyres — Identification system |
| 102 | Annex B (informative) Correspondence between ISO designations and other designations |
| 113 | Bibliography |
