BSI 14/30243471 DC:2014 Edition
$13.70
BS ISO 15082. Road vehicles. Tests for rigid plastic safety glazing materials
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 47 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | 1 Scope 2 Normative references 3 Terms and definitions |
| 7 | 4 Test conditions 5 Conditioning of test specimens 6 Application of tests 7 Optical properties test 8 Head-form/fragmentation test 8.1 Principle 8.2 Apparatus |
| 8 | 8.3 Test specimens |
| 9 | 8.4 Procedure 8.5 Expression of results |
| 10 | 9 Head-form test with deceleration measurement 9.1 Principle 9.2 Test conditions 9.3 Conditioning of test pieces |
| 12 | 9.4.1 Head-form weight: head-form (as shown in Figure 4 for data transmission via co-axial (BNC) cables) with total mass of 10.0 kg +0.2/-0.0 kg, which allows the simultaneous determination of HIC-values. The components of the head-form according to … 9.4.2 Measuring device – for recording and evaluation of the measured deceleration curves ax(t), ay(t) and az(t), transmitted from the head-form acceleration gauges via cables or wireless: acceleration gauges, measuring and recording instruments accor… |
| 13 | Remarks Material |
| 14 | 9.4.3 Supporting fixture for testing flat test specimens, as shown in Figure 5. The fixture is composed of two steel frames, with machined edges, 50 mm wide, fitting one over the other and faced with rubber gaskets about 3 mm thick, and 50 mm +1/-0 mm… 9.4.4 Supporting fixture for testing complete panes: The support shall consist of a rigid piece corresponding to the shape of the pane so that the head-form weight faces the internal surface. The pane shall be clamped to the supporting structure by me… 9.4.5 Equipment to calibrate the head-form 9.4.5.1 Drop appliance which must allow drop heights between 50 mm and 254 mm to be adjusted exactly to within 1 mm. A guide system is not necessary for these small drop heights. 9.4.5.2 Impact plate made of steel, dimensions 600 mm x 600 mm, minimum thickness 50 mm, flatness tolerance t = 0.05 mm, determined in accordance with ISO 1101. 9.5 Calibration procedure and adjustment of the head-form |
| 15 | 9.6 Test Pieces: Flat test specimens (1170 mm +0/-2 mm x 570 mm +0/-2 mm) or complete panes shall be subjected to testing. 9.7 Test Procedure: In case of flat test specimens, fix the specimen in the supporting frames (Paragraph 9.4.3). In case of tests on complete panes, clamp the pane to a support which has a shape corresponding to the pane (Paragraph 9.4.4). |
| 16 | 9.8 Evaluation 9.9 Expression of results |
| 17 | 10 227g ball test 10.1.1 Principle 10.1.2 Apparatus |
| 18 | 10.1.3 Test specimens 10.1.4 Procedure 10.1.5 Expression of results 10.2 2260 g ball test 10.2.1 Principle 10.2.2 Apparatus 10.2.3 Test specimens 10.2.4 Procedure |
| 19 | 10.2.5 Expression of results 11 Abrasion resistance test 11.1 Principle 11.2 Abrasion resistance under dry conditions 11.2.1 Apparatus |
| 22 | 11.3 Test specimens 11.4 Standardization of Abrading Wheels 11.5 Procedure |
| 29 | 12.1 Principle 12.2. Apparatus |
| 30 | 12.3. Test specimens 12.4. Procedure |
| 31 | 13 Chemical resistance test 13.1 Principle 13.2 Chemical agents to be used 13.3 Test specimens |
| 32 | 13.4 Test procedure |
| 33 | 13.5 Expression of results 14 Resistance to simulated weathering test 14.1 Principle 14.2. Exposure apparatus 14.3 Test specimens |
| 34 | 14.4 Procedure |
| 35 | 14.5 Evaluation 14.6 Expression of results 14.7 Report of test parameters 15 Fire Resistance Test 15.1 Principle 15.2 Apparatus |
| 36 | 15.3 Test specimens 15.4 Test procedure 15.5 Expression of results |
