BSI 15/30326200 DC:2015 Edition
$13.70
BS EN 16903. Plastics piping systems. Sustainability of construction works. Product Category Rules (PCR) for buried plastics piping systems
| Published By | Publication Date | Number of Pages |
| BSI | 2015 | 29 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | 30326200 |
| 3 | 41_e_stf |
| 4 | Contents Page |
| 8 | 1 Scope |
| 9 | 2 Normative references 3 Terms and definitions 4 Abbreviations 5 General aspects 5.1 Objective of the PCR for buried plastics piping systems |
| 10 | 5.2 Types of EPD with respect to life cycle stages covered 5.3 Comparability of EPD for construction products 5.4 Additional information |
| 11 | 5.5 Ownership, responsibility and liability for the EPD 5.6 Communication formats 6 Product Category Rules for LCA 6.1 Product category 6.2 Life cycle stages and their information modules to be included 6.2.1 General 6.2.2 A1-A3, Product stage, information modules 6.2.3 A4-A5, Construction process stage, information modules 6.2.4 B1-B5, Use stage, information modules related to the buried plastics piping systems 6.2.5 B6-B7, use stage, information modules related to the operation of the buried plastics piping systems 6.2.6 C1-C4 End-of-life stage, information modules 6.2.7 D, Benefits and loads beyond the system boundary, information module |
| 12 | 6.3 Calculation rules for the LCA 6.3.1 Functional unit 6.3.2 Declared unit 6.3.3 Reference service life (RSL) 6.3.4 System boundaries 6.3.4.1 General 6.3.4.2 Product stage |
| 14 | 6.3.4.3 Construction stage |
| 15 | 6.3.4.4 Use stage |
| 16 | 6.3.4.5 End-of-life stage |
| 17 | 6.3.4.6 Benefits and loads beyond the product system boundary in module D 6.3.5 Criteria for the exclusion of inputs and outputs 6.3.6 Selection of data |
| 18 | 6.3.7 Data quality requirements 6.3.8 Developing product level scenarios 6.3.9 Units 6.4 Inventory analysis 6.4.1 Collecting data 6.4.2 Calculation procedures 6.4.3 Allocation of input flows and output emissions 6.4.3.1 General 6.4.3.2 Co-product allocation 6.4.3.3 Allocation procedure of reuse, recycling and recovery 6.5 Impact assessment |
| 19 | 7 Content of the EPD 7.1 Declaration of general information 7.2 As EN 15804.Declaration of environmental parameters derived from LCA 7.2.1 General 7.2.2 Rules for declaring LCA information per module 7.2.3 Parameters describing environmental impacts 7.2.4 Parameters describing resource use 7.2.5 Other environmental information describing different waste categories and output flows 7.3 Scenarios and additional technical information 7.3.1 General 7.3.2 Construction process stage 7.3.2.1 A4, Transport to the construction site 7.3.2.2 A5, Installation in the trench |
| 20 | 7.3.3 B1-B7 use stage 7.3.3.1 B1-B5 use stage related to the buried plastics piping systems’ material 7.3.3.2 Reference service life 7.3.3.3 B6, use of energy and B7, use of water 7.3.4 End-of-life 7.4 Additional information on release of dangerous substances to, soil and ground water during the use stage 7.4.1 Indoor air 7.4.2 Soil and ground water 7.5 Aggregation of information modules 8 Project report 8.1 General 8.2 LCA-related elements of the project report 8.3 Documentation on additional information 8.4 Data availability for verification |
| 21 | 9 Verification and validity of an EPD |
| 22 | Annex A (informative)Waste A.1 End-of-waste A.2 Properties of hazardous waste for Table 5 |
| 23 | Annex B (informative) Formula for calculation of the different modules of the environmental profile for Module D B.1 Introduction B.2 Modules A to C B.3 Module D |
| 26 | Annex C (informative)List of standards |
