🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BSI 23/30456788 DC 2023

BSI 23/30456788 DC 2023

$13.70

BS ENISO 19085-12 Woodworking machines. Safety – Part 12. Tenoning/profiling machines

Published By Publication Date Number of Pages
BSI 2023 66
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

PDF Catalog

PDF Pages PDF Title
8 Foreword
9 Introduction
11 1 Scope
12 2 Normative references
13 3 Terms and definitions
22 4 Safety requirements and measures for controls
4.1 Safety and reliability of control systems
4.2 Control devices
4.2.1 General
4.2.2 Single end tenoning machines with manual feed sliding table
4.2.3 Single end tenoning machines with mechanical feed sliding table
4.2.4 Single end tenoning and/or profiling machines with mechanical feed
4.2.5 Double end tenoning and/or profiling machines with mechanical feed
23 4.2.6 Angular systems for tenoning and profiling with mechanical feed
4.3 Start
4.3.1 Direct start
4.3.2 Start via control power-on
24 4.3.3 Laser marking unit
4.4 Safe stops
4.4.1 General
4.4.2 Normal stop
4.4.3 Operational stop
4.4.4 Emergency stop
4.5 Braking function of tool spindles
4.6 Mode selection
25 4.7 Tool speed changing
4.7.1 Speed changing by shifting the belts on the pulleys
4.7.2 Speed changing by incremental speed change motor
4.7.3 Infinitely variable speed by frequency inverter
4.8 Failure of any power supply
4.9 Manual reset control
4.10 Standstill detection and monitoring
4.11 Machine moving parts speed monitoring
26 4.12 Time delay
4.13 Teleservice
5 Safety requirements and measures for protection against mechanical hazards
5.1 Stability
5.2 Risk of break-up during operation
5.3 Tool and tool fixing design
5.3.1 General
27 5.3.2 Spindle locking
5.3.3 Circular saw blade fixing device
5.3.4 Flange dimensions for circular saw blades
5.3.5 Spindle rings
5.4 Braking
5.4.1 Braking of tools
5.4.2 Maximum run-down time
5.4.3 Brake release
28 5.5 Safeguards
5.5.1 Fixed guards
5.5.2 Interlocking moveable guards
5.5.3 Hold-to-run control
5.5.4 Two hand control
5.5.5 Electro-sensitive protective equipment (ESPE)
5.5.6 Pressure sensitive protective equipment (PSPE)
5.5.7 Enabling control
5.6 Prevention of access to hazardous moving parts
5.6.1 Single end tenoning machines with manual feed sliding table
29 5.6.2 Single end tenoning machines with mechanical feed sliding table
30 5.6.3 Single end tenoning and/or profiling machines with mechanical feed
31 5.6.4 Double end tenoning and/or profiling machines with mechanical feed
35 5.6.5 Angular systems for tenoning and profiling with mechanical feed
36 5.6.6 Guarding of drives
37 5.6.7 Guarding of the chain or feed mechanisms
38 5.7 Impact hazard
5.8 Clamping devices
5.8.1 Single end tenoning machines with sliding table
39 5.8.2 Machines other than single end tenoning machines with sliding table
5.9 Measures against ejection
5.9.1 General
5.9.2 Guards materials and characteristics
40 5.9.3 Devices to minimize the possibility or effect of ejection or kickback
42 5.10 Workpiece support and guides
5.10.1 Single end tenoning machines with sliding table
5.10.2 Single end tenoning and/or profiling machines with mechanical feed
5.10.3 Double end tenoning and/or profiling machines with mechanical feed
43 5.10.4 Angular systems for tenoning and profiling with mechanical feed
5.10.5 Workpiece returner
6 Safety requirements and measures for protection against other hazards
6.1 Fire
44 6.2 Noise
6.2.1 Noise reduction at the design stage
6.2.2 Noise emission measurement
6.3 Emission of chips and dust
6.4 Electricity
6.5 Ergonomics and handling
6.6 Lighting
6.7 Pneumatics
6.8 Hydraulics
45 6.9 Electromagnetic compatibility
6.10 Laser
6.11 Static electricity
6.12 Errors of fitting
6.13 Isolation
6.14 Maintenance
6.15 Relevant but not significant hazards
6.16 Extreme temperatures
6.17 Substances
46 7 Information for use
7.1 Warning devices
7.2 Marking
7.2.1 General
7.2.2 Additional markings
7.3 Instruction handbook
7.3.1 General
7.3.2 Additional information
49 Annex€A (informative) List of significant hazards
51 Annex€B (informative) Performance levels required
53 Annex€C Stability test
54 Annex€D (normative) Test for braking function
55 Annex€E (normative) Impact test for guards
56 Annex€F (normative) Noise test code
64 Annex€ZA (informative) Relationship between this European Standard and the essential requirements of Directive 2006/42/EC aimed to be covered
66 Bibliography

Related products

BSI 23/30456788 DC 2023
$13.70