Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
CAN/CSA-O160-16:2016 Edition

CAN/CSA-O160-16:2016 Edition

$22.75

Formaldehyde emissions standard for composite wood products

Published By Publication Date Number of Pages
CSA 2016 25
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Preface

This is the first edition of CAN/CSA-O160, Formaldehyde emissions standard for composite wood products.

Note: For more information on VOCs, refer to Annex B.

This Standard is intended to harmonize with the existing California Air Resources Board’s Airborne Toxic Control Measures (ATCM) 17 CCR (§93120 et seq. on all sections relating to responsibilities of manufacturers and third party certifiers).

Note: California Air Resources Board’s Airborne Toxic Control Measures (ATCM) 17 CCR is referred to as CARB throughout this Standard.

CSA Group acknowledges that the development of this Standard was made possible, in part, by the financial support of Standards Council of Canada, with support from Health Canada. Health Canada provides health-based science and policy advice that supports actions to improve air quality and health of Canadians, in part through the development of health-based residential product emissions Standards.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

Scope

1.1

This Standard applies to newly manufactured, unfinished composite wood panels prior to use in construction, finishing, or installation. The composite wood panel categories covered are

a) hardwood plywood (HWPW) (including composite and veneer core);

b) particleboard (PB);

c) medium density fibreboard (MDF); and

d) thin MDF.

Note: Refer to Clause 3.1 for further clarification.

1.2

This Standard does not apply to the following:

a) cellulosic fiber insulating boards complying with ASTM C208;

b) curved plywood;

c) hardwood plywood with a lumber core or non-composite core material;

d) finger-jointed lumber; and

e) structural wood products made with moisture resistant adhesives complying with the referenced standards:

i) structural Plywood conforming to CSA O121, CSA O151, CSA O153, or NIST PS 1;

ii) oriented strand board (OSB) specified with the Exposure 1 or Exterior bond classification in accordance with CSA O325, NIST PS 2, ICC Acceptance Criteria or Canadian Codes and Materials Centre (CCMC) Evaluation Criteria or ANSI standards for code compliant applications;

iii) structural Composite Lumber, Specification for Structural Composite Lumber Products conforming to ASTM D5456 or CCMC Evaluation Criteria for Structural Composite Lumber;

iv) structural Glued Laminated Timber conforming to CAN/CSA-O122 or ANSI A190.1;

v) wood I-Joists Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists conforming to ASTM D5055 or CCMC Evaluation Criteria for Wood I-joists; and

vi) cross-laminated timber specified to ANSI/APA PRG 320.

1.3

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the Standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Related products

CAN/CSA-O160-16
$22.75