ICC IECC Commentary 2nd 2015
$47.13
International Energy Conservation Code and Commentary
| Published By | Publication Date | Number of Pages |
| ICC | 2015 | 357 |
This comprehensive publication provides a convenient reference for regulations in the 2015 International Energy Conservation Code® (IECC®).
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | 2015 IECC® CODE AND COMMENTARY |
| 2 | 2015 IECC® CODE AND COMMENTARY TITLE PAGE |
| 3 | COPYRIGHT |
| 4 | PREFACE |
| 6 | TABLE OF CONTENTS |
| 8 | IECC—COMMERCIAL PROVISIONS TABLE OF CONTENTS |
| 10 | CHAPTER 1 [CE] SCOPE AND ADMINISTRATION GENERAL COMMENTS PURPOSE PART 1—SCOPE AND APPLICATION SECTION C101 SCOPE AND GENERAL REQUIREMENTS |
| 11 | FIGURE C101.4.4 MIXED OCCUPANCY |
| 12 | SECTION C102 ALTERNATE MATERIALS—METHOD OF CONSTRUCTION, DESIGN OR INSULATING SYSTEMS |
| 13 | PART 2—ADMINISTRATION AND ENFORCEMENT SECTION C103 CONSTRUCTION DOCUMENTS |
| 15 | SECTION C104 INSPECTIONS |
| 17 | SECTION C105 VALIDITY SECTION C106 REFERENCED STANDARDS |
| 18 | SECTION C107 FEES SECTION C108 STOP WORK ORDER |
| 19 | SECTION C109 BOARD OF APPEALS BIBLIOGRAPHY |
| 20 | CHAPTER 2 [CE] DEFINITIONS GENERAL COMMENTS PURPOSE SECTION C201 GENERAL SECTION C202 GENERAL DEFINITIONS |
| 38 | CHAPTER 3 [CE] GENERAL REQUIREMENTS GENERAL COMMENTS PURPOSE DISCUSSION AND DEVELOPMENT OF THE CLIMATE ZONE MAP |
| 39 | SECTION C301 CLIMATE ZONES |
| 41 | FIGURE C301.1 CLIMATE ZONES |
| 42 | FIGURE C301.3 CLIMATE ZONE DEFINITIONS |
| 43 | TABLE C301.3(1) INTERNATIONAL CLIMATE ZONE DEFINITIONS TABLE C301.3(2) INTERNATIONAL CLIMATE ZONE DEFINITIONS |
| 44 | TABLE C301.1 CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 45 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 46 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 47 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 48 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 49 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 50 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 51 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 52 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 53 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 54 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 55 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 56 | TABLE C301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 57 | SECTION C302 DESIGN CONDITIONS SECTION C303 MATERIALS, SYSTEMS AND EQUIPMENT |
| 58 | FIGURE C303.1.1 SAMPLE CERTIFICATE OF INSULATION |
| 60 | FIGURE C303.1.3(1) SAMPLE NATIONAL FENESTRATION RATING COUNCIL (NFRC) LABEL |
| 61 | TABLE C303.1.3(1) DEFAULT GLAZED FENESTRATION U-FACTORS TABLE C303.1.3(2) DEFAULT DOOR U-FACTORS TABLE C303.1.3(3) DEFAULT GLAZED FENESTRATION SHGC AND VT FIGURE C303.1.3(2) VISUALLY VERIFIABLE WINDOW CHARACTERISTICS |
| 63 | BIBLIOGRAPHY |
| 64 | CHAPTER 4 [CE] COMMERCIAL ENERGY EFFICIENCY GENERAL COMMENTS FIGURE 4C(1) EXAMPLES OF BUILDING TYPES COVERED BY CHAPTER 4 (CE) PURPOSE |
| 65 | SECTION C401 GENERAL |
| 66 | SECTION C402 BUILDING ENVELOPE REQUIREMENTS |
| 67 | FIGURE C402.1 GRAPHIC SUMMARY OF ENVELOPE REQUIREMENTS |
| 70 | FIGURE C402.1.3 HOW TO MEASURE SURFACE AREAS [SEE COMMENTARY FIGURE C402.1] |
| 71 | FIGURE C402.1.3(1) R-VALUE REQUIREMENTS FOR BELOW-GRADE WALLS FIGURE C402.1.4 EXAMPLE OF U-FACTOR METHOD |
| 72 | TABLE C402.1.3 OPAQUE THERMAL ENVELOPE INSULATION COMPONENT MINIMUM REQUIREMENTS, R-VALUE METHODa |
| 73 | TABLE C402.1.4 OPAQUE THERMAL ENVELOPE ASSEMBLY MAXIMUM REQUIREMENTS, U-FACTOR METHOD |
| 74 | EQUATION 4-1 TABLE C402.1.4.1 EFFECTIVE R-VALUES FOR STEEL STUD WALL ASSEMBLIES EQUATION 4-2 |
| 76 | FIGURE C402.1.5 COMPONENT PERFORMANCE EXAMPLE |
| 77 | FIGURE C402.2.2 REQUIREMENT FOR ROOFS |
| 78 | FIGURE C402.2.3 REQUIREMENTS FOR EXTERIOR ABOVE-GRADE WALLS |
| 79 | FIGURE C402.2.4 R-VALUE REQUIREMENTS FOR FLOORS |
| 80 | FIGURE C402.2.5 REQUIREMENT FOR INSULATING SLABS-ON-GRADE |
| 81 | EQUATION 4-3 TABLE C402.3 MINIMUM ROOF REFLECTANCE AND EMITTANCE OPTIONS |
| 82 | TABLE C402.4 BUILDING ENVELOPE FENESTRATION MAXIMUM U-FACTOR AND SHGC REQUIREMENTS |
| 83 | EQUATION 4-4 |
| 84 | EQUATION 4-5 |
| 85 | FIGURE C402.4.3 WINDOW PROJECTION FACTOR |
| 88 | FIGURE C402.5.1.1 REQUIREMENTS FOR SEALING THE BUILDING ENVELOPE |
| 89 | TABLE C402.5.2 MAXIMUM AIR LEAKAGE RATE FOR FENESTRATION ASSEMBLIES |
| 91 | FIGURE C402.5.7 VESTIBULES |
| 92 | FIGURE C402.5.8 IC-RATED RECESSED LIGHT SECTION C403 BUILDING MECHANICAL SYSTEMS |
| 97 | TABLE C403.2.3(1) MINIMUM EFFICIENCY REQUIREMENTS: ELECTRICALLY OPERATED UNITARY AIR CONDITIONERS AND CONDENSING UNITS |
| 98 | TABLE C403.2.3(1)—continued MINIMUM EFFICIENCY REQUIREMENTS: ELECTRICALLY OPERATED UNITARY AIR CONDITIONERS AND CONDENSING UNITS |
| 99 | TABLE C403.2.3(2) MINIMUM EFFICIENCY REQUIREMENTS: ELECTRICALLY OPERATED UNITARY AND APPLIED HEAT PUMPS |
| 100 | TABLE C403.2.3(2)—continued MINIMUM EFFICIENCY REQUIREMENTS: ELECTRICALLY OPERATED UNITARY AND APPLIED HEAT PUMPS |
| 101 | TABLE C403.2.3(3) MINIMUM EFFICIENCY REQUIREMENTS: ELECTRICALLY OPERATED PACKAGED TERMINAL AIR CONDITIONERS, PACKAGED TERMINAL HEAT PUMPS, SINGLE-PACKAGE VERTICAL AIR CONDITIONERS, SINGLE VERTICAL HEAT PUMPS, ROOM AIR CONDITIONERS AND ROOM AIR-CONDITIONER HEAT PUMPS |
| 102 | TABLE C403.2.3(3)—continued MINIMUM EFFICIENCY REQUIREMENTS: ELECTRICALLY OPERATED PACKAGED TERMINAL AIR CONDITIONERS, PACKAGED TERMINAL HEAT PUMPS, SINGLE-PACKAGE VERTICAL AIR CONDITIONERS, SINGLE VERTICAL HEAT PUMPS, ROOM AIR CONDITIONERS AND ROOM AIR-CONDITIONER HEAT PUMPS TABLE 403.2.3(4) WARM-AIR FURNACES AND COMBINATION WARM-AIR FURNACES/AIR-CONDITIONING UNITS, WARM-AIR DUCT FURNACES AND UNIT HEATERS, MINIMUM EFFICIENCY REQUIREMENTS |
| 103 | TABLE C403.2.3(5) MINIMUM EFFICIENCY REQUIREMENTS: GAS- AND OIL-FIRED BOILERS TABLE C403.2.3(6) MINIMUM EFFICIENCY REQUIREMENTS: CONDENSING UNITS, ELECTRICALLY OPERATED |
| 104 | TABLE C403.2.3(7) WATER CHILLING PACKAGES – EFFICIENCY REQUIREMENTS |
| 105 | TABLE C403.2.3(8) MINIMUM EFFICIENCY REQUIREMENTS: HEAT REJECTION EQUIPMENT |
| 106 | TABLE C403.2.3(9) MINIMUM EFFICIENCY AIR CONDITIONERS AND CONDENSING UNITS SERVING COMPUTER ROOMS TABLE C403.2.3(10) HEAT TRANSFER EQUIPMENT EQUATION 4-6 EQUATION 4-7 |
| 107 | FIGURE C403.2.4.1 THERMOSTAT TEMPERATURE CONTROL |
| 108 | FIGURE C403.2.4.1(1) SEPARATE COOLING AND HEATING SYSTEMS WITHIN A GROUP OF ZONES |
| 109 | FIGURE C403.2.4.1(2) INDEPENDENT PERIMETER ZONE HEATING SYSTEM |
| 111 | FIGURE C403.2.4.1.2 DEAD BAND THERMOSTAT CONTROL FIGURE C403.2.4.1.2DEAD BAND THERMOSTAT CONTROL |
| 117 | TABLE C403.2.7(1) ENERGY RECOVERY REQUIREMENT (Ventilation systems operating less than 8,000 hours per year) TABLE C403.2.7(2) ENERGY RECOVERY REQUIREMENT (Ventilation systems operating not less than 8,000 hours per year) |
| 118 | TABLE C403.2.8 MAXIMUM NET EXHAUST FLOW RATE, CFM PER LINEAR FOOT OF HOOD LENGTH |
| 120 | FIGURE C403.2.9 DUCT INSULATION |
| 122 | EQUATION 4-8 |
| 124 | TABLE C403.2.10 MINIMUM PIPE INSULATION THICKNESS (in inches)a, c |
| 125 | TABLE C403.2.12.1(1) FAN POWER LIMITATION |
| 126 | TABLE C403.2.12.1(2) FAN POWER LIMITATION PRESSURE DROP ADJUSTMENT |
| 128 | TABLE C403.2.14(1) MINIMUM EFFICIENCY REQUIREMENTS: COMMERCIAL REFRIGERATION TABLE C403.2.14(2) MINIMUM EFFICIENCY REQUIREMENTS: COMMERCIAL REFRIGERATORS AND FREEZERS |
| 129 | TABLE C403.2.14(2)—continued MINIMUM EFFICIENCY REQUIREMENTS: COMMERCIAL REFRIGERATORS AND FREEZERS |
| 131 | TABLE C403.3(1) MINIMUM CHILLED-WATER SYSTEM COOLING CAPACITY FOR DETERMINING ECONOMIZER COOLING REQUIREMENTS |
| 132 | TABLE C403.3(2) EQUIPMENT EFFICIENCY PERFORMANCE EXCEPTION FOR ECONOMIZERS |
| 133 | TABLE C403.3.1 DX COOLING STAGE REQUIREMENTS FOR MODULATING AIRFLOW UNITS FIGURE C403.3.3(1) AIR ECONOMIZER OPERATION |
| 134 | FIGURE C403.3.1(2) “STRAINER-CYCLE” WATER ECONOMIZER FIGURE C403.3.1(3) WATER PRECOOLING ECONOMIZER WITH TWO-WAY VALVES |
| 135 | FIGURE C403.3.1(4) AIR PRECOOLING WATER ECONOMIZER |
| 136 | TABLE C403.3.3.3 HIGH-LIMIT SHUTOFF CONTROL SETTING FOR AIR ECONOMIZERS |
| 139 | TABLE C403.4.1.1 EFFECTIVE DATES FOR FAN CONTROL |
| 142 | TABLE C403.4.2.5 BOILER TURNDOWN |
| 147 | TABLE C403.4.6 MAXIMUM HOT GAS BYPASS CAPACITY |
| 148 | SECTION C404 SERVICE WATER HEATING (MANDATORY) FIGURE C404.1 ELEMENTS COVERED BY SECTION C404 |
| 150 | TABLE C404.2 MINIMUM PERFORMANCE OF WATER-HEATING EQUIPMENT |
| 151 | FIGURE C404.4(1) HEAT TRAP AND INSULATION REQUIREMENTS FOR NONCIRCULATING SYSTEMS |
| 152 | FIGURE C404.4(2) HEAT TRAPS ON A TANK WITH CONNECTIONS ON THE BOTTOM FIGURE C404.4(3) HEAT TRAP THROUGH A FLEXIBLE PIPE LOOP |
| 153 | FIGURE C404.4(4) HEAT TRAPS ON A TANK WITH CONNECTIONS ON SIDES |
| 154 | TABLE C404.5.1 PIPING VOLUME AND MAXIMUM PIPING LENGTHS |
| 157 | SECTION C405 ELECTRICAL POWER AND LIGHTING SYSTEMS |
| 161 | FIGURE C405.2.1 REQUIRED LIGHTING CONTROLS |
| 165 | FIGURE C405.2.2.2 LIGHT-REDUCTION CONTROLS |
| 167 | FIGURE C405.2.3.2(1) DAYLIGHT ZONE ADJACENT TO FENESTRATION IN A WALL |
| 168 | FIGURE C405.2.3.2(2) DAYLIGHT ZONE UNDER A ROOFTOP MONITOR FIGURE C405.2.3.2(3) DAYLIGHT ZONE UNDER A SLOPED ROOFTOP MONITOR |
| 169 | FIGURE C405.2.3.3 DAYLIGHT ZONE UNDER A ROOF FENESTRATION ASSEMBLY |
| 172 | EQUATION 4-9 FIGURE C405.4 APPLYING THE LIGHTING REQUIREMENTS TO A PRIVATE OFFICE |
| 173 | TABLE C405.4.2(1) INTERIOR LIGHTING POWER ALLOWANCES: BUILDING AREA METHOD |
| 174 | TABLE C405.4.2(2) INTERIOR LIGHTING POWER ALLOWANCES: SPACE-BY-SPACE METHOD TABLE C405.4.2(2)—continued INTERIOR LIGHTING POWER ALLOWANCES: SPACE-BY-SPACE METHOD |
| 175 | TABLE C405.4.2(2)—continued INTERIOR LIGHTING POWER ALLOWANCES: SPACE-BY-SPACE METHOD |
| 176 | FIGURE C405.4.2 MULTIUSE FACILITY FIGURE C405.4.2(1) TOTAL LIGHTING POWER ALLOWANCE CALCULATION USING THE BUILDING AREA METHOD FIGURE C405.4.2(2) TOTAL LIGHTING POWER ALLOWANCE CALCULATION USING THE SPACE-BY-SPACE METHOD |
| 177 | EQUATION 4-10 |
| 178 | TABLE C405.5(1) EXTERIOR LIGHTING ZONES |
| 179 | TABLE C405.5(2) INDIVIDUAL LIGHTING POWER ALLOWANCES FOR BUILDING EXTERIORS |
| 180 | FIGURE C405.5.1 ENERGY-EFFICIENT LIGHTING SOURCE TABLE C405.7 MINIMUM NOMINAL EFFICIENCY LEVELS FOR 10 CFR 431 LOW-VOLTAGE DRY-TYPE DISTRIBUTION TRANSFORMERS |
| 181 | SECTION C406 ADDITIONAL EFFICIENCY PACKAGE OPTIONS |
| 182 | TABLE C405.8(1) MINIMUM NOMINAL FULL-LOAD EFFICIENCY FOR 60 HZ NEMA GENERAL PURPOSE ELECTRIC MOTORS (SUBTYPE I) RATED 600 VOLTS OR LESS |
| 183 | TABLE C405.8(2) MINIMUM NOMINAL FULL-LOAD EFFICIENCY OF GENERAL PURPOSE ELECTRIC MOTORS (SUBTYPE II) AND ALL DESIGN B MOTORS GREATER THAN 200 HORSEPOWER |
| 184 | TABLE C405.8(3) MINIMUM AVERAGE FULL-LOAD EFFICIENCY FOR POLYPHASE SMALL ELECTRIC MOTORS TABLE C405.8(4) MINIMUM AVERAGE FULL LOAD EFFICIENCY FOR CAPACITOR-START CAPACITOR-RUN AND CAPACITOR-START INDUCTION-RUN SMALL ELECTRIC MOTORS |
| 186 | SECTION C407 TOTAL BUILDING PERFORMANCE |
| 190 | TABLE C407.5.1(1) SPECIFICATIONS FOR THE STANDARD REFERENCE AND PROPOSED DESIGNS |
| 191 | TABLE C407.5.1(1)—continued SPECIFICATIONS FOR THE STANDARD REFERENCE AND PROPOSED DESIGNS |
| 192 | TABLE C407.5.1(2) HVAC SYSTEMS MAP |
| 193 | TABLE C407.5.1(3) SPECIFICATIONS FOR THE STANDARD REFERENCE DESIGN HVAC SYSTEM DESCRIPTIONS |
| 194 | TABLE C407.5.1(4) NUMBER OF CHILLERS TABLE C407.5.1(5) WATER CHILLER TYPES |
| 196 | SECTION C408 SYSTEM COMMISSIONING |
| 199 | BIBLIOGRAPHY |
| 202 | CHAPTER 5 [CE] EXISTING BUILDINGS GENERAL COMMENTS PURPOSE SECTION C501 GENERAL |
| 203 | SECTION C502 ADDITIONS |
| 205 | SECTION C503 ALTERATIONS |
| 207 | SECTION C504 REPAIRS SECTION C505 CHANGE OF OCCUPANCY OR USE |
| 208 | CHAPTER 6 [CE] REFERENCED STANDARDS GENERAL COMMENTS PURPOSE |
| 209 | FIGURE 6[CE] REFERENCED STANDARDS |
| 210 | AAMA AHAM AHRI |
| 211 | AMCA ANSI APSP ASHRAE |
| 212 | ASME ASTM CRRC |
| 213 | CSA CTI DASMA DOE |
| 214 | ICC IEEE IES ISO |
| 215 | NEMA NFPA NFRC SMACNA UL |
| 216 | US-FTC WDMA |
| 218 | INDEX |
| 228 | IECC—RESIDENTIAL PROVISIONS TABLE OF CONTENTS |
| 230 | CHAPTER 1 [RE] SCOPE AND ADMINISTRATION GENERAL COMMENTS PURPOSE PART 1—SCOPE AND APPLICATION SECTION R101 SCOPE AND GENERAL REQUIREMENTS |
| 231 | FIGURE R101.2(1) CONDITIONED ENVELOPE FIGURE R101.2(2) BUILDING ENVELOPE |
| 232 | FIGURE R101.4.1 MIXED OCCUPANCY |
| 233 | SECTION R102 ALTERNATIVE MATERIALS, DESIGN AND METHODS OF CONSTRUCTION AND EQUIPMENT |
| 234 | PART 2—ADMINISTRATION AND ENFORCEMENT SECTION R103 CONSTRUCTION DOCUMENTS |
| 236 | SECTION R104 INSPECTIONS |
| 239 | SECTION R105 VALIDITY SECTION R106 REFERENCED STANDARDS |
| 240 | SECTION R107 FEES SECTION R108 STOP WORK ORDER |
| 241 | SECTION R109 BOARD OF APPEALS BIBLIOGRAPHY |
| 242 | CHAPTER 2 [RE] DEFINITIONS GENERAL COMMENTS PURPOSE SECTION R201 GENERAL SECTION R202 GENERAL DEFINITIONS |
| 244 | FIGURE R202(1) BASEMENT WALLS |
| 256 | CHAPTER 3 [RE] GENERAL REQUIREMENTS GENERAL COMMENTS PURPOSE DISCUSSION AND DEVELOPMENT OF THE CLIMATE ZONE MAP |
| 257 | SECTION R301 CLIMATE ZONES |
| 259 | FIGURE R301.1 CLIMATE ZONES |
| 260 | FIGURE R301.3 CLIMATE ZONE DEFINITIONS |
| 261 | TABLE R301.3(1) INTERNATIONAL CLIMATE ZONE DEFINITIONS TABLE R301.3(2) INTERNATIONAL CLIMATE ZONE DEFINITIONS |
| 262 | TABLE R301.1 CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 263 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 264 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 265 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 266 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 267 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 268 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 269 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 270 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 271 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 272 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 273 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 274 | TABLE R301.1—continued CLIMATE ZONES, MOISTURE REGIMES, AND WARM-HUMID DESIGNATIONS BY STATE, COUNTY AND TERRITORY |
| 275 | SECTION R302 DESIGN CONDITIONS SECTION R303 MATERIALS, SYSTEMS AND EQUIPMENT |
| 276 | FIGURE R303.1.1 SAMPLE CERTIFICATE OF INSULATION |
| 278 | FIGURE R303.1.3(1) SAMPLE NATIONAL FENESTRATION RATING COUNCIL (NFRC) LABEL |
| 279 | TABLE R303.1.3(1) DEFAULT GLAZED FENESTRATION U-FACTORS TABLE R303.1.3(2) DEFAULT DOOR U-FACTORS FIGURE R303.1.3(2) VISUALLY VERIFIABLE WINDOW CHARACTERISTICS TABLE R303.1.3(3) DEFAULT GLAZED FENESTRATION SHGC AND VT |
| 281 | BIBLIOGRAPHY |
| 282 | CHAPTER 4 [RE] RESIDENTIAL ENERGY EFFICIENCY GENERAL COMMENTS PURPOSE SECTION R401 GENERAL |
| 283 | FIGURE R401.1(1) CONDITIONED ENVELOPE FIGURE R401.1(2) BUILDING ENVELOPE |
| 285 | SECTION R402 BUILDING THERMAL ENVELOPE FIGURE R401.3 CERTIFICATE |
| 287 | TABLE R402.1.2 INSULATION AND FENESTRATION REQUIREMENTS BY COMPONENT |
| 288 | FIGURE R402.1.2 EXTERIOR R-VALUES |
| 290 | TABLE R402.1.4 EQUIVALENT U-FACTORS |
| 292 | FIGURE R402.2.1(1) TYPICAL ROOF ASSEMBLY |
| 293 | FIGURE R402.2.1(2) RAISED-HEEL TRUSS |
| 294 | FIGURE R402.2.5(1) EXTERIOR INSULATION |
| 295 | FIGURE R402.2.5(2) INTERIOR INSULATION TABLE R402.2.6 STEEL-FRAME CEILING, WALL AND FLOOR INSULATION (R-VALUE) |
| 296 | FIGURE R402.2.8 SLAB INSULATION METHODS |
| 297 | FIGURE R402.2.9(1) WALKOUT BASEMENT FIGURE R402.2.9(2) EXTERIOR BASEMENT INSULATION |
| 298 | FIGURE R402.2.10 SLAB INSULATION METHODS |
| 299 | FIGURE R402.2.11 CRAWL SPACE WALL INSULATION |
| 303 | FIGURE R402.4 TYPICAL SOURCES OF AIR LEAKAGE IN THE HOME |
| 304 | TABLE R402.4.1.1 AIR BARRIER AND INSULATION INSTALLATION |
| 306 | FIGURE R402.4.5 IC-RATED RECESSED LIGHT |
| 307 | SECTION R403 SYSTEMS |
| 309 | TABLE R403.6.1 MECHANICAL VENTILATION SYSTEM FAN EFFICACY |
| 312 | SECTION R404 ELECTRICAL POWER AND LIGHTING SYSTEMS SECTION R405 SIMULATED PERFORMANCE ALTERNATIVE (PERFORMANCE) |
| 322 | TABLE R405.5.2(1) SPECIFICATIONS FOR THE STANDARD REFERENCE AND PROPOSED DESIGNS |
| 323 | TABLE R405.5.2(1)—continued SPECIFICATIONS FOR THE STANDARD REFERENCE AND PROPOSED DESIGNS |
| 324 | TABLE R405.5.2(1)—continued SPECIFICATIONS FOR THE STANDARD REFERENCE AND PROPOSED DESIGNS TABLE R405.5.2(2) DEFAULT DISTRIBUTION SYSTEM EFFICIENCIES FOR PROPOSED DESIGNS |
| 325 | SECTION R406 ENERGY RATING INDEX COMPLIANCE ALTERNATIVE |
| 326 | TABLE R406.4 MAXIMUM ENERGY RATING INDEX |
| 328 | CHAPTER 5 [RE] EXISTING BUILDINGS GENERAL COMMENTS PURPOSE SECTION R501 GENERAL |
| 329 | SECTION R502 ADDITIONS |
| 331 | SECTION R503 ALTERATIONS |
| 333 | SECTION R504 REPAIRS SECTION R505 CHANGE OF OCCUPANCY OR USE |
| 336 | CHAPTER 6 [RE] REFERENCED STANDARDS GENERAL COMMENTS PURPOSE |
| 337 | FIGURE 6 [RE] REFERENCED STANDARDS |
| 338 | AAMA ACCA APSP ASHRAE ASTM |
| 339 | CSA DASMA ICC IIEEE |
| 340 | NFPA NFRC UL US-FTC WDMA |
| 342 | APPENDIX RA: RECOMMENDED PROCEDURE FOR WORST-CASE TESTING OF ATMOSPHERIC VENTING SYSTEMS UNDER R402.4 OR R405 CONDITIONS ≤ 5ACH50 GENERAL COMMENTS PURPOSE SECTION RA101 SCOPE SECTION RA201 GENERAL DEFINITIONS SECTION RA301 TESTING PROCEDURE |
| 343 | TABLE RA301.1(1) CAZ DEPRESSURIZATION LIMITS TABLE RA301.1(2) ACCEPTABLE DRAFT TEST CORRECTION |
| 344 | TABLE RA301.1(3) ACCEPTABLE DRAFT TEST CORRECTION |
| 346 | APPENDIX RB: SOLAR-READY PROVISIONS-DETACHED ONE AND TWO FAMILY DWELLINGS, MULTIPLE SINGLE FAMILY DWELLINGS (TOWNHOUSES) GENERAL COMMENTS PURPOSE SECTION RB101 SCOPE SECTION RB102 GENERAL DEFINITION SECTION RB103 SOLAR-READY ZONE |
| 348 | INDEX |
| 354 | ICC TRAINING AND EDUCATION DEPARTMENT |
| 355 | GET IMMEDIATE DOWNLOADS OF THE STANDARDS YOU NEED |
| 356 | ICC EVALUATION SERVICE |
| 357 | 2015 I-CODE ESSENTIALS |
Related products
-
ICC IBC Commentary Vol 1 2nd 2015
International Building Code and Commentary Volume 1 Published By Publication Date Number of Pages ICC…
