Shopping Cart

No products in the cart.

IEEE 1095 1990

$72.04

IEEE Guide for Installation of Vertical Generators and Generator/Motors for Hydroelectric Applications

Published By Publication Date Number of Pages
IEEE 1990 40
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

New IEEE Standard – Inactive – Superseded. This standard describes installation procedures for synchronous generators and generator/motors rated 5000 kVA and above, to be coupled to hydraulic turbines having vertical shafts.

PDF Catalog

PDF Pages PDF Title
1 Title Page
3 Introduction
Participants
5 CONTENTS
7 1. Introduction and Scope
2. References
8 3. Tools and Facilities
3.1 General
3.2 Erection Contractor-Supplied Tools
3.3 Manufacturer-Supplied Tools
9 3.4 Customer-Supplied Materials, Services, and Facilities
4. Personnel
5. Generator Construction
5.1 General Arrangement
10 5.2 Stator Construction
11 5.3 Rotor Construction
12 5.4 Shaft and Coupling
5.5 Thrust Bearing
14 5.6 Guide Bearings
15 5.7 Brakes and Jacks
5.8 Field Assembly Requirements
16 6. Preparation of Generator and Turbine Shafts in Factory
6.1 Factory Preassembly and Alignment
6.2 Field Alignment
7. Installation Precautions
7.1 Position References
17 7.2 Handling of Generator Parts
7.3 Matching of Parts
7.4 Use of Plumb Lines
7.5 Precautions in Welding
18 7.6 Cleanliness
7.7 Keeping Records
8. Receiving, Storing, and Unpacking
8.1 Receiving
19 8.2 Storing
21 8.3 Unpacking
9. Erection Procedures
9.1 General
22 9.2 Generator Shipped Completely Assembled
9.3 Generator Assembled in the Field, Thrust Bearing Above the Rotor, Spring-Type or Self-Equalizing-type Thrust Bearing
23 9.4 Generator Assembled in the Field, Thrust Bearing Above the Rotor, Adjustable-Shoe-Type Thrust Bearing
25 9.5 Generator Assembled in the Field, Thrust Bearing Below the Rotor, Spring-Type or Self-Equalizing-Type Thrust Bearing
26 9.6 Generator Assembled in the Field, Thrust Bearing Below the Rotor, Adjustable-Shoe-Type Thrust Bearing
27 10. Details of Erection Procedures
10.1 Placing a Foundation Bolts
10.2 Positioning and Grouting of Soleplates
28 10.3 Assembly of Stator
29 10.4 Assembly of Rotor
31 10.5 Assembly of Thrust Bearings
10.6 Assembly of Guide Bearings
32 10.7 Installation of Lubrication System
10.8 Checking Air Gap
10.9 Check of Insulation Against Shaft Currents
10.10 Closing of Generator-Turbine Coupling
33 10.11 Shaft-Plumb and Straightness Check
10.12 Equalizing the Load on Adjustable-Shoe-Type Bearings
10.13 Check of Shaft Runout
10.14 Assembly of Rotating Exciters (If Provided), Collector Rings, and Brush Rigging
34 10.15 Installation of Instruments and Relays
11. Mechanical Run
11.1 General
35 11.2 Preparation for Initial Start
11.3 Initial Start
36 11.4 Check of Shaft Runout
12. Balancing
37 13. Insulation Testing and Drying Out
13.1 Measurement of Winding Insulation Resistance
13.2 Drying Out of Windings
38 13.3 High-Potential Tests
14. Initial Operation
14.1 No-Load Operation and Excitation
14.2 Connection to Power System
14.3 Load Rejection Tests
39 14.4 Operation Check of Shaft Runout
15. Field Tests
15.1 Vertical Hydraulic-Turbine Generator Shaft Runout Tolerances, Installation Check
40 15.2 Electrical Tests
IEEE 1095 1990
$72.04