IEEE 1310-2012(Redline)
$60.67
IEEE Recommended Practice for Thermal Cycle Testing of Form-Wound Stator Bars and Coils for Large Rotating Machines (Redline)
| Published By | Publication Date | Number of Pages |
| IEEE | 2012 | 30 |
Revision Standard – Inactive-Reserved. This procedure is intended for form-wound bars/coils for rotating machines rated 10 kV or more at 50 Hz or 60 Hz that are subjected to many transitions from no-load to full-load current during normal operations, and where rapid load variations are typical. Only the thermal cyclic degradation within the groundwall insulation and/or the conductor package and delamination of the groundwall insulation from the conductor are addressed by this test. The procedure is applicable to indirectly-cooled machine types such as: — combustion turbine generators — pumped storage or peaking duty hydrogenerators — synchronous condensers — cyclic duty water pump motors Various pass/fail criteria are presented, and the ones that apply in a specific circumstance must be agreed between user and manufacturer prior to commencement of testing
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | IEEE Std 1310-2012 Front Cover |
| 3 | Title page |
| 6 | Notice to users Laws and regulations Copyrights Updating of IEEE documents Errata Patents |
| 8 | Participants |
| 10 | Introduction |
| 11 | Contents |
| 12 | Important notice 1. Overview |
| 13 | 1.1 Scope |
| 14 | 1.2 Purpose 2. Normative references |
| 16 | 3. Definitions 4. Thermal cycling test description 4.1 Test objects 4.2 Method of heating |
| 17 | 4.3 Method of cooling 4.4 Temperature cycle and schedule |
| 18 | 5. Thermal cycling test setup 5.1 Quantity of bars/coils required for testing |
| 19 | 5.2 Positioning and setting up bars/coils for test |
| 21 | 5.3 Temperature criteria, measurement, and control |
| 22 | 6. Bar/coil preparation 7. Diagnostic tests preceding and during thermal cycling |
| 23 | 7.1 Electrical proof test for the groundwall insulation 7.2 Dissipation factor and tip-up measurements 7.3 Partial discharge measurements 7.4 Physical measurements 7.5 Tap test—mechanical delamination detection |
| 24 | 7.6 Surface resistivity 8. Post-thermal cycle tests 8.1 Proof tests |
| 25 | 8.2 Breakdown or voltage endurance test 8.3 Dissection |
| 26 | 9. Preparation of test report |
| 27 | Annex A (normative) Sample calculation for estimating current rating of test supply A.1 Approximate method for calculation |
| 28 | A.2 Loss of thermal energy, practical tests A.3 Test equipment |
| 29 | Annex B (informative) Decisions required by manufacturer/purchaser/testing facility |
| 30 | Annex C (informative) Bibliography |
Related products
-
IEEE 1785.2 2016
IEEE Standard for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and…
-
IEEE 1210-2004/Cor 1-2014
IEEE Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable – Corrigendum…
-
ASHRAE Guideline 21 2012
IEEE/ASHRAE Guideline 21-2012 Guide for the Ventilation and Thermal Management of Batteries for Stationary Applications…
-
IEEE 1900.4.1 2013
IEEE Standard for Interfaces and Protocols Enabling Distributed Decision Making for Optimized Radio Resource Usage…
-
IEEE 1310-2012(Redline)
IEEE Recommended Practice for Thermal Cycle Testing of Form-Wound Stator Bars and Coils for Large…
-
IEEE 1610 2016:2017 Edition
IEEE Guide for the Application of Faulted Circuit Indicators on Distribution Circuits Published By Publication…
-
IEEE 1310-2012
IEEE Recommended Practice for Thermal Cycle Testing of Form-Wound Stator Bars and Coils for Large…
-
IEEE 1010-2022
IEEE Guide for Control of Hydroelectric Power Plants (Approved Draft) Published By Publication Date Number…
-
IEEE 1785.1-2012
IEEE Standard for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and…
-
IEEE/ISO/IEC 21451 2 2010
ISO/IEC/IEEE International Standard for Information technology — Smart transducer interface for sensors and actuators —…
-
IEEE 802.3cs-2022
IEEE Standard for Ethernet Amendment 2: Physical Layers and Management Parameters for Increased-Reach Point-to-Multipoint Ethernet…
-
IEEE 1665 2010
IEEE Guide for the Rewind of Synchronous Generators, 50 Hz and 60 Hz, Rated 1…
-
IEEE 1785.2-2016
IEEE Standard for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and…
-
IEEE 1785.3 2016
IEEE Recommended Practice for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz…
-
IEEE 1800-2012
IEEE Standard for SystemVerilog–Unified Hardware Design, Specification, and Verification Language Published By Publication Date Number…
-
IEEE 1010-2022(Redline)
IEEE Guide for Control of Hydroelectric Power Plants (Redline) Published By Publication Date Number of…
-
IEEE 1010-2022
IEEE Guide for Control of Hydroelectric Power Plants (Published) Published By Publication Date Number of…
-
IEEE 1410 2011
IEEE Guide for Improving the Lightning Performance of Electric Power Overhead Distribution Lines Published By…
-
IEEE 1300 2012
IEEE Guide for Cable Connections for Gas-Insulated Substations Published By Publication Date Number of Pages…
-
IEEE 1785.1-2012
IEEE Standard for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and…
-
IEEE 1800-2017
IEEE Standard for SystemVerilog–Unified Hardware Design, Specification, and Verification Language (Superseded) Published By Publication Date…
-
IEEE 8802-1X:2013/Amd. 1:2016 Edition
ISO/IEC/IEEE International Standard – Information technology – Telecommunications and information exchange between systems – Local…
-
IEEE 1003.1 2008/Cor2 2016
IEEE Standard for Information Technology — Portable Operating System Interface (POSIX(TM)) – Base Specifications, Issue…
-
IEEE 1785.1 2013
IEEE Standard for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and…
-
IEEE 1010-2022
IEEE Guide for Control of Hydroelectric Power Plants (Approved Draft) Published By Publication Date Number…
-
IEEE 1010-2022
IEEE Guide for Control of Hydroelectric Power Plants (Published) Published By Publication Date Number of…
-
IEEE P63195-1:2022 Edition
IEEE/IEC International Draft Standard – Measurement procedure for the assessment of power density of human…
-
IEEE 1207 2011
IEEE Guide for the Application of Turbine Governing Systems for Hydroelectric Generating Units Published By…
-
IEEE 24748 3 2012
IEEE Guide:–Adoption of ISO/IEC TR 24748-3:2011, Systems and software engineering-Life cycle management-Part 3: Guide to…
-
IEEE ISO IEC 8802 1X:2013 Amd.1:2016 Edition
ISO/IEC/IEEE International Standard – Information technology – Telecommunications and information exchange between systems – Local…
-
IEEE 1010-2022(Redline)
IEEE Guide for Control of Hydroelectric Power Plants (Redline) Published By Publication Date Number of…
-
IEEE ISO IEC 21451 2 2010
ISO/IEC/IEEE Standard for Information technology — Smart transducer interface for sensors and actuators — Part…
-
IEEE 802.1Qaz 2011
IEEE Standard for Local and metropolitan area networks–Media Access Control (MAC) Bridges and Virtual Bridged…
-
IEEE 1310 2012
IEEE Recommended Practice for Thermal Cycle Testing of Form-Wound Stator Bars and Coils for Large…
-
IEEE 1210 2004 Cor1 2014
IEEE Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable – Corrigendum…
-
IEEE 1810 2017
IEEE Guide for the Installation of Fire-Rated Cables Suitable for Hydrocarbon Pool Fires for Critical…
-
IEEE 1003.1 2008 Cor2 2016
IEEE Standard for Information Technology — Portable Operating System Interface (POSIX(R)) – Base Specifications, Issue…
-
IEEE 1800 2017:2018 Edition
IEEE Standard for SystemVerilog–Unified Hardware Design, Specification, and Verification Language Published By Publication Date Number…
-
IEEE C62.72 2016
IEEE Guide for the Application of Surge-Protective Devices for Use on the Load Side of…
-
IEEE 802.3cr-2021
IEEE Standard for Ethernet Amendment 10: Maintenance #14: Isolation Published By Publication Date Number of…
