IEEE 1727 2013
$46.04
IEEE Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage
| Published By | Publication Date | Number of Pages |
| IEEE | 2013 | 57 |
New IEEE Standard – Active. Induced voltage working procedures for underground transmission circuits are established in this guide. A transmission circuit when de-energized will have an induced voltage when in a common duct bank with an energized circuit. The induced voltage may be a possible safety hazard. The induced voltage may be determined by modeling the circuits and by measurement. This guide addresses the working procedures to follow when performing work where induced voltage is present.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | IEEE Std 1727™-2013 front cover |
| 3 | Title page |
| 6 | Notice to users Laws and regulations Copyrights Updating of IEEE documents Errata Patents |
| 8 | Participants |
| 10 | Introduction |
| 11 | Contents |
| 13 | IMPORTANT NOTICE 1. Overview 1.1 Scope 1.2 Purpose |
| 14 | 2. Normative references 3. Definitions, acronyms, and abbreviations 3.1 Definitions |
| 15 | 3.2 Acronyms and abbreviations 4. Safety/Warning 4.1 Safety 4.2 Safe voltage |
| 16 | 4.3 Warnings 4.4 Grounding 4.5 Grounding methods 4.6 Grounding methodologies 4.6.1 Open and Isolate all phases and sheath wires at both ends of the underground section, ground only at the work location (single point) |
| 17 | 4.6.2 Ground all phases and metallic sheath at both ends of the underground section |
| 18 | 4.6.3 Ground all phases and sheath wires at one end only of the underground section |
| 19 | 4.6.4 Fault Current 5. General principles 5.1 Equipotentiality A work zone is Equipotential when all the conducting devices present have the same electrical potential. 5.2 Setting up Equipotentiality |
| 20 | 5.3 Personal protection measures for operators 5.3.1 Basic equipment 5.3.2 Specialized equipment for the operation 5.4 Prior to work 5.4.1 Circuit modeling |
| 21 | 5.4.2 Circuit Measurements 6. Single point grounding work procedures 6.1 Cable pulling 6.1.1 Levels of induced voltages during cable pull |
| 22 | 6.1.2 Removing steel rope and cutting the cable |
| 23 | 6.2 Jointing 6.2.1 Main steps 6.2.2 Preparation |
| 24 | 6.2.3 Slip-on joints |
| 30 | 6.2.4 Plug connector joints |
| 35 | 6.3 Terminating 6.3.1 Installing the first termination 6.3.2 Parking of single piece parts |
| 36 | 6.3.3 Installing the second termination on a completed circuit 6.4 Outdoor termination procedure |
| 44 | 7. Scenarios for multi-point grounding work procedures 7.1 General |
| 45 | 7.2 Different scenarios 7.3 Building a new line close to an existing line 7.3.1 Progress from one end towards the other one |
| 47 | 7.3.2 Progress from two ends towards the middle |
| 50 | 7.3.3 Cutting an existing line close to an existing line 7.4 Adding a length of line and two joints in an existing line close to another existing line Cutting: “C” |
| 51 | 7.4.1 Adding short length of cable Jointing “J” |
| 52 | Annex A (informative) Examples of induction modeling |
| 57 | Annex B (informative) Bibliography |
Related products
-
IEEE IEC 62243 2012
IEC 62243:2012(E) (IEEE Std 1232-2010): Artificial Intelligence Exchange and Service Tie to All Test Environments…
-
IEEE 1722.1-2013
IEEE Standard for Device Discovery, Connection Management, and Control Protocol for IEEE 1722(TM) Based Devices…
-
IEEE 1727-2013
IEEE Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage Published By Publication…
-
IEEE 1725-2011
IEEE Standard for Rechargeable Batteries for Cellular Telephones Published By Publication Date Number of Pages…
-
IEEE 1720 2012
IEEE Recommended Practice for Near-Field Antenna Measurements Published By Publication Date Number of Pages IEEE…
-
IEEE 1720-2012
IEEE Recommended Practice for Near-Field Antenna Measurements Published By Publication Date Number of Pages IEEE…
-
IEEE 1717 2012
IEEE Standard for Testing Circuit Integrity Cables Using a Hydrocarbon Pool Fire Test Protocol Published…
-
IEEE 1707 2015
IEEE Recommended Practice for the Investigation of Events at Nuclear Facilities Published By Publication Date…
-
IEEE 1726-2013
IEEE Guide for the Functional Specification of Fixed-Series Capacitor Banks for Transmission System Applications Published…
-
IEEE 1277 2010
IEEE Standard General Requirements and Test Code for Dry-Type and Oil-Immersed Smoothing Reactors for DC…
-
IEEE 1827 2016:2017 Edition
IEEE Guide for Electrical and Control Design of Hydroelectric Water Conveyance Facilities Published By Publication…
-
IEEE 1722.1-2013:2018 Edition
IEEE Standard for Device Discovery, Connection Management, and Control Protocol for IEEE 1722(TM) Based Devices…
-
IEEE 1277-2010
IEEE Standard General Requirements and Test Code for Dry-Type and Oil-Immersed Smoothing Reactors for DC…
-
IEEE 1717-2012
IEEE Standard for Testing Circuit Integrity Cables Using a Hydrocarbon Pool Fire Test Protocol Published…
-
IEEE 1725-2011(Redline)
IEEE Standard for Rechargeable Batteries for Cellular Telephones (Redline) Published By Publication Date Number of…
-
IEEE 1527 2018
IEEE Recommended Practice for the Design of Buswork Located in Seismically Active Areas Published By…
-
IEEE 1627-2019
IEEE Standard for Transient Overvoltage Protection of DC Electrification Systems by Application of DC Surge…
-
IEEE 1667 2010
IEEE Standard for Authentication in Host Attachments of Transient Storage Devices Published By Publication Date…
-
IEEE 1722.1 2013/Cor1 2018:2019 Edition
IEEE Standard for Device Discovery, Connection Management, and Control Protocol for IEEE 1722(TM) Based Devices…
-
IEEE 1729 2014
IEEE Recommended Practice for Electric Power Distribution System Analysis Published By Publication Date Number of…
-
IEEE 1127-2013(Redline)
IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance…
-
IEEE 1727 2013 Cor1 2015
IEEE Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage — Corrigendum 1…
-
IEEE 1726 2014
IEEE Guide for the Functional Specification of Fixed-Series Capacitor Banks for Transmission System Applications Published…
-
IEEE 1722 2016
IEEE Standard for a Transport Protocol for Time-Sensitive Applications in Bridged Local Area Networks Published…
-
IEEE 1724 2011
IEEE Guide for the Preparation of a Transmission Line Design Criteria Document Published By Publication…
-
IEEE 1127-2023
IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance…
-
IEEE 1722.1 2013
IEEE Standard for Device Discovery, Connection Management, and Control Protocol for IEEE 1722(TM) Based Devices…
-
IEEE 1127-2023
IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance…
-
IEEE 1127-2023
IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance…
-
IEEE 1725 2011
IEEE Standard for Rechargeable Batteries for Cellular Telephones Published By Publication Date Number of Pages…
-
IEEE 1722 2011
IEEE Standard for Layer 2 Transport Protocol for Time Sensitive Applications in a Bridged Local…
-
IEEE 1722-2016
IEEE Standard for a Transport Protocol for Time-Sensitive Applications in Bridged Local Area Networks Published…
-
IEEE 1722-2011
IEEE Standard for Layer 2 Transport Protocol for Time Sensitive Applications in a Bridged Local…
-
IEEE 1127-2013(Redline)
IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance…
-
IEEE 1127 2014
IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance…
-
IEEE IEC 62243 2012
IEC 62243:2012(E) (IEEE Std 1232-2010): Artificial Intelligence Exchange and Service Tie to All Test Environments…
-
IEEE 1725-2011(Redline)
IEEE Standard for Rechargeable Batteries for Cellular Telephones (Redline) Published By Publication Date Number of…
-
IEEE 1722 2016 Cor1 2016
IEEE Approved Draft Standard for a Transport Protocol for Time Sensitive Applications in a Bridged…
-
IEEE 1127-2013
IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance…
-
IEEE 1717-2012
IEEE Standard for Testing Circuit Integrity Cables Using a Hydrocarbon Pool Fire Test Protocol Published…
