Shopping Cart

No products in the cart.

IEEE 422 1986

$21.67

IEEE Guide for the Design and Installation of Cable Systems in Power Generating Stations

Published By Publication Date Number of Pages
IEEE 1986 34
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

New IEEE Standard – Inactive – Withdrawn. This guide applies to both nuclear and non-nuclear electric power generating stations — except for the special requirements of wire and cable installations in Class 1E systems of nuclear stations — for which the user should refer to ANSI/IEEE Std 690-1984.

PDF Catalog

PDF Pages PDF Title
11 1 General
1.1 Scope and Purpose
1.2 References
12 2 Cable Performance
2.1 Definitions
2.2 Service Conditions
2.3 Cable Performance
2.3.1 Service Life
2.3.2 Thermal Stability
2.3.3 Moisture Resistance
2.3.4 Chemical Resistance
2.3.5 Flame Propagation Resistance
2.3.6 Radiation Resistance
Conductor Sizing and Voltage Rating of Power Cables
3.1 Design Considerations
13 3.1.1 Ambient Temperature
3.1.2 Current Loading
System Fault Level
3.1.4 Voltage Drop
System Nominal Voltage and Grounding
Electrical Segregation of Cable Systems
4.1 Cable Classifications
4.2 Segregation
Medium-voltage Power Cables
14 4.2.2 Low-voltage Power and Control Cables
4.2.3 Instrumentation Cables
5 Separation of Redundant Cable Systems
Redundant Cable Systems
5.2 Design Considerations
5.2.1 Potential Hazard Areas
Cable Spreading Area
15 6 Shielding and Shield Grounding
Medium-voltage Power Cable
6.1.1 Definition
6.1.2 Shielding Practices
6.1.3 Shield Termination Practices
6.1.4 Grounding Practices
16 6.1.5 Shield Losses That Affect Ampacity
Induced Shield Voltages
17 Cables
18 6.2 Instrumentation Cable
6.2.1 Definitions
6.2.2 Methods for Noise Reduction
Voltage to
20 6.2.3 Shielding Practices
6.2.4 Grounding Practices
Cable Penetration Fire Stops Fire Breaks System Enclosures and Coatings
7.1 Definitions
21 7.2 Cable Penetration Fire Stops
7.2.1 Design Considerations
7.2.2 Sleeve and Tray Penetrations
7.3 Cable Fire Breaks
7.4 Cable System Enclosure
7.5 Cable Coatings
Fire Detection Systems
22 Fig 1 Determination of Potential High Cable Concentration
23 8.1 Heat Detectors
8.1.1 Fixed-Temperature Detectors
Combination Fixed-Temperature and Rate-of-Rise Temperature Detectors
8.2 Smoke Detectors
8.2.1 Photoelectric Detectors
8.2.2 Combustion Products Detectors
24 8.3 Flame Detectors
8.4 Design Considerations
Fire Extinguishing Systems
9.1 Extinguishing Systems
Water in Fixed Extinguishing Installations
Carbon Dioxide in Fixed Extinguishing Installations
Dry Chemicals and Carbon Dioxide in Portable Extinguishers
9.1.4 Halogen Extinguishing Systems
9.1.5 Foam Extinguishing Systems
Fixed Fire Extinguishing System Application and Design
25 Installation and Handling
10.1 Storage
10.2 Installation
10.2.1 Protection of Cable
Table 3 Low Temperature Limits for Cable Handling
26 10.2.2 Supporting Cables in Vertical Runs
10.2.3 Dressing Cables in Vertical Runs
Cable Pulling Lengths in Conduit and Duct Systems
10.3.1 Maximum Distance for Cable Pulled in Conduits
10.3.2 Maximum Cable Pulling Length
27 10.3.3 Maximum Allowable Pulling Tension
10.3.4 Maximum Allowable Sidewall Pressure
10.3.5 Expected Pulling Tension
28 Runs
29 10.3.6 Critical Jamming Ratio
Weight Correction Factor W. )
30 10.3.7 Expected Sidewall Pressure
Acceptance Testing of Installed Cables
11.1 Purpose
11.2 Tests
Raceways
31 12.1 Definitions
12.2 Conduit
12.2.1 Conduit Application
12.2.2 Conduit System Design
32 12.2.3 Conduit Installation
12.3 Cable Tray
12.3.1 Tray Design
33 12.3.2 Tray System Design
12.3.3 Tray Application
12.3.4 Tray Load Capacity
12.4 Cable Tray Installation
12.4.1 Dropouts
12.4.2 Covers
34 12.4.3 Grounding
12.4.4 Identification
12.4.5 Supports
12.4.6 Location
12.5 Wireways
IEEE 422 1986
$21.67